November 5, 2017, 03:39 AM | #1 |
Senior Member
Join Date: November 26, 2012
Location: Concord NH
Posts: 1,002
|
270 reloads
My friend is having trouble with some of his reloads. These have all been full length resized and overall length is within sammi specs. Sometime probably 50%. After firing a round it gets stuck in the chamber and is a real bear to get the bolt back and eject the round. Any ideas what could be causing this?
|
November 5, 2017, 06:13 AM | #2 |
Senior Member
Join Date: December 29, 2006
Posts: 155
|
If you are not trolling us, there is just one word -----STOP!!!!!!!
All signs point to over-pressure and if all you say is true pull the rounds apart now, confirm powder and throw weight. Re-weigh bullets --is the recipe correct for the weight? If the rifle shoots factory ammo OK then it is all his reloads and you need to help him before he destroys his gun and injures either himself or others. |
November 5, 2017, 09:01 AM | #3 |
Senior Member
Join Date: October 1, 2013
Posts: 689
|
STOP STOP STOP what is the load recipe? Rule #1 Start low and work up
|
November 5, 2017, 09:52 AM | #4 |
Senior Member
Join Date: June 23, 2013
Location: Central Taxylvania..
Posts: 3,609
|
Exactly what they said!!!
STOP!!! Recheck your bullet and powder weights!! |
November 5, 2017, 10:40 AM | #5 |
Senior Member
Join Date: November 26, 2012
Location: Concord NH
Posts: 1,002
|
He has stopped and will not use those reloads again, I am going to pull the bullets and weigh the powder charge and try to figure out what went wrong.
|
November 5, 2017, 10:46 AM | #6 |
Senior Member
Join Date: October 1, 2014
Posts: 315
|
why doesn't HE pull the loads
|
November 5, 2017, 10:48 AM | #7 |
Senior Member
Join Date: November 26, 2012
Location: Concord NH
Posts: 1,002
|
No bullet puller
|
November 5, 2017, 01:53 PM | #8 |
Senior Member
Join Date: February 13, 2002
Location: Canada
Posts: 12,453
|
He not able to tell you what load he used?
|
November 5, 2017, 04:24 PM | #9 |
Senior Member
Join Date: April 10, 2008
Location: Alaska
Posts: 7,014
|
NHShOOTER an tell that when he pulls the bullet.
By the way, I just go the Hornady Lever Version Collet type, I like it a lot. Vastly better than the hammers (which are ok for a single, but 5+ are really no fun) I wasn't sure how well the press would do as its an up motion, but I get tight, give it a bit of a pop and out they come.
__________________
Science and Facts are True whether you believe it or not |
November 5, 2017, 09:00 PM | #10 |
Senior Member
Join Date: June 23, 2013
Location: Central Taxylvania..
Posts: 3,609
|
RC20
I got an RCBS collet puller at an auction. Love the thing! |
November 6, 2017, 09:07 PM | #11 |
Senior Member
Join Date: October 9, 2004
Location: Kennewick, WA
Posts: 294
|
What was his load? Powder, bullet, primer, case? If everything is per a loading manual, then he might need to check his scale, or have a gunsmith check out his rifle. More information would be helpful.
__________________
NRA Endowment Member |
|
|