|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
March 28, 2020, 04:28 PM | #1 |
Senior Member
Join Date: October 22, 2016
Posts: 3,889
|
Pins getting stuck during tumbling solutions
Currently I'm only having this problem when tumbling .32 revolver brass. I have two different lengths of pins, one is .355" in length and the other is the standard .25" length.
I have run the .355" in the .32's before and didn't have too many with stuck pins, but the last time I did .32 tumbling I used the .25" and near every one got stuck. Thankfully I decap before tumbling, so I can push the pins out with a rod thru the flash hole, but I'm getting tired of the stuck pins So, I'm wondering if anyone here has ever used ball bearings or very small steel shot for tumbling? This is the only solution I can think of to completely eliminate the issues of stuck pins for the smaller calibers.
__________________
"We always think there's gonna be more time... then it runs out."
|
March 28, 2020, 05:17 PM | #2 |
Senior Member
Join Date: September 6, 2013
Location: JAX, FL
Posts: 377
|
pretty sure you are saying they are hanging up in the primer cavity and not the flash hole. I gotta say, I do not recall ever having pins hang up in the cavity in 10 years. I have rarely had three pins wedge themselves in the flash hole together though.
have you had these .25" pins long and have you actually measured them because that's an odd size. the standard length is .255" and probably that length to specifically avoid the problem you are having. I can understand the rare and occasional short pin getting through the manufacturing process though. as to your question about other media, a while back I recall someone selling little diamond/triangle shaped media but can't find them right know. edit: I found these but have no experience with any of these. I'd measure my flash holes and cavities large and small then select the size you hope will work. Sorry I am unable to provide any real help. https://www.kramerindustriesonline.c...umbling-media/
__________________
“Some people spend an entire lifetime wondering if they made a difference in the world. But, the Marines don't have that problem.” ― Ronald Reagan Last edited by oley55; March 28, 2020 at 05:30 PM. |
March 28, 2020, 06:37 PM | #3 |
Senior Member
Join Date: October 22, 2016
Posts: 3,889
|
No, it's not the flash hole or primer pocket, it's the neck of the cases themselves.
$70 for a pound of media is not an option.
__________________
"We always think there's gonna be more time... then it runs out."
|
March 28, 2020, 07:31 PM | #4 |
Staff
Join Date: March 4, 2005
Location: Ohio
Posts: 21,063
|
You are saying the collect as a sort of block in the case mouths? That's a new one on me. It sounds like the case diameter is just the wrong size for the pin diameters. Are the 0.25's a different diameter than the .355's?
__________________
Gunsite Orange Hat Family Member CMP Certified GSM Master Instructor NRA Certified Rifle Instructor NRA Benefactor Member and Golden Eagle |
March 28, 2020, 08:59 PM | #5 |
Senior Member
Join Date: October 22, 2016
Posts: 3,889
|
The .25" and .355" figures are the lengths of the pins. The diameters are a bit different, but they have no effect on them getting stuck.
__________________
"We always think there's gonna be more time... then it runs out."
Last edited by TruthTellers; March 28, 2020 at 09:13 PM. |
March 29, 2020, 06:24 AM | #6 |
Senior Member
Join Date: April 15, 2018
Location: Baton Rouge - Louisiana
Posts: 407
|
In my quest for the perfect tumbling media, one of my less disastrous departures from SS media were small porcelain polishing beads which come in every size and shape you can imagine. Spring manufacturers use them. I came across them as a few would come in bulk deliveries of stain less steel rings I use to make chainmail armor. -
Here's a link / example - https://cmtopline.com/products/angle...iABEgJio_D_BwE Find a size too large to get stuck in a flash hole for your brass. |
March 29, 2020, 07:33 AM | #7 |
Senior Member
Join Date: July 26, 2015
Posts: 526
|
maybe this might work? Stainless jewelers mix. It's not real clear what the lengths are but there is a video which might give some reference.
__________________
He may look dumb, but that's just a disguise. -Charlie Daniels |
March 29, 2020, 09:27 AM | #8 |
Senior Member
Join Date: February 19, 2018
Location: Centerville, OH
Posts: 347
|
Yep...this sure looks familiar. I just wet tumbled about 500 .300 AAC Blackout cases with SS pins. More than half were just cut down from .223 Rem, so I was tumbling to remove the burrs prior to resizing/forming, and the rest were once fired that required cleaning.
Anyway, I had 4 or 5 pins get stuck just like that across the flash hole. It was pretty easy to dislodge them with a push pin through the primer cup. Given that it was less than a handful out of a large quantity of cases, I wouldn’t bother changing anything. Anyway, if you were looking for a different SS media, check this out: https://www.ammobrass.com/product-pa...r-wet-tumblers Last edited by markr6754; March 29, 2020 at 09:33 AM. |
March 29, 2020, 03:14 PM | #9 |
Staff
Join Date: March 4, 2005
Location: Ohio
Posts: 21,063
|
OK. They are stuck diametrically down where the brass thickens near the head. Yes, you just need some too long or too short to do that. I would guess any pin long enough so it tilts at least 30° crossing from one side of the case to the other would avoid that. So, anything over 0.357". I think you proved that to yourself with your 0.355's, which were right on the edge of that number. If you can find some that are 3/16" (0.1875") it doesn't look like they will get stuck, either.
I did a search on stainless media, and the 6mm×1mm (0.24"×0.039") and 6.5mm×1.2mm (0.256"×0.047") seem to be most common. They are just too short. I would call STM and ask what size theirs is. It's $40, but you get 5 lb. If it is the same stuff, obviously, don't bother. This stainless pin process was actually invented by board member Hummer70 about 30 years ago and shared among some top competitors. He got his pins from this company, which is a manufacturer. He found a diameter of 0.041" works best, which is closer to 1 mm, rather than the 1.2 mm 0.047" pins commonly sold. The pin maker will cut them any length your request, but the catch is you have to order 50 lbs minimum to order direct, so you would want to line up a number of friends to share the cost with. One other thing that might make a difference is using more soap. Hummer70 says he likes Ivory dishwashing detergent best with Dawn second. He uses a full ounce in a Thumbler B. That much detergent will provide more slipperiness than the usual teaspoon, and that may help with preventing things from getting stuck. Liquid soap (dissolved soap flakes) might be even better. I forgot to ask: Did you tumble the pins by themselves for a time before first use to dull the wire's cut edges? That, too, should make them less prone to sticking.
__________________
Gunsite Orange Hat Family Member CMP Certified GSM Master Instructor NRA Certified Rifle Instructor NRA Benefactor Member and Golden Eagle |
March 29, 2020, 06:17 PM | #10 | |
Senior Member
Join Date: October 22, 2016
Posts: 3,889
|
Quote:
The shorter pins I'll use with .38 and larger.
__________________
"We always think there's gonna be more time... then it runs out."
|
|
|
|