May 20, 2023, 05:12 PM | #1 |
Senior Member
Join Date: August 12, 2009
Location: Athens, Georgia
Posts: 2,526
|
Squib
Had a squib today. This is the second time for me but the first time that the bullet went far enough into the barrel for the cylinder to turn. The first time was years ago and was a reload. Today's squib was factory ammo. You can see the base of the bullet lodged in the barrel:
|
May 20, 2023, 05:41 PM | #2 |
Senior Member
Join Date: March 3, 2010
Posts: 124
|
Yikes. Mind sharing what the brand of ammo is?
_______________ *I'd give right arm to be ambidextrous* |
May 20, 2023, 06:07 PM | #3 |
Senior Member
Join Date: August 12, 2009
Location: Athens, Georgia
Posts: 2,526
|
Ammo Incorporated 125 grain TMJ in .38 Special.
|
May 20, 2023, 07:03 PM | #4 |
Senior Member
Join Date: March 3, 2010
Posts: 124
|
You might consider sending this pic to them along with the lot number. I (personally) wouldn't shoot any more of this batch.
You're fortunate you didn't shoot another round after that. That's one thing that concerns me when I shoot rapid fire - not stopping in time. _______________ *I'd give right arm to be ambidextrous* |
May 20, 2023, 08:11 PM | #5 |
Senior Member
Join Date: November 13, 2022
Posts: 342
|
Wow that's scary I am glad you did not fire the gun again into the barrel obstruction and hurt yourself!
|
May 21, 2023, 12:11 AM | #6 |
Staff
Join Date: March 11, 2006
Location: Upper US
Posts: 28,871
|
Absolutely inform the manufacturer, ASAP!
Don't just consider it, DO IT! They NEED to know something went wrong, before they can begin to figure out a fix. If there was no powder in your squib round, where did the powder go? Into another case, perhaps? is there a double charge waiting out there in the as yet unfired rounds of that production batch?? OR was it some mechanical flaw that prevented charging that round but all the others are ok??? If the factory doesn't even know there is a problem, it can't be fixed. Tell them what happened, where you got the ammo, lot# and any other information they ask for. I have no personal experience with Ammo Incorporated, so can't say how they will respond. I know what I'd expect them to do. Tell them what happened and then please tell us what they did about it.
__________________
All else being equal (and it almost never is) bigger bullets tend to work better. |
May 21, 2023, 07:01 AM | #7 |
Senior Member
Join Date: August 12, 2009
Location: Athens, Georgia
Posts: 2,526
|
I sent them a message yesterday using their contact us link on their website.
I'll let you know when I get a response. |
May 23, 2023, 06:06 PM | #8 |
Senior Member
Join Date: August 12, 2009
Location: Athens, Georgia
Posts: 2,526
|
I got an Email from Rick at Ammo Inc asking apologizing for the squib and asking for the lot number and some other information. It looks like Ammo Inc is trying to do right.
|
June 11, 2023, 08:05 AM | #9 |
Senior Member
Join Date: August 12, 2009
Location: Athens, Georgia
Posts: 2,526
|
Just a quick update: Ammo Inc sent me a UPS return label via Email and I returned the unused cartridges, along with the empty cases to them. They refunded what I had spent on the ammunition.
|
December 5, 2023, 02:48 PM | #10 |
Junior Member
Join Date: August 24, 2012
Posts: 3
|
I know this is an older thread, but had my first squib today with the same ammo - Ammo Incorporated 125 grain TMJ in .38 Special.
Did not think to take a picture, but wondering if I should go ahead and contact Ammo Incorporated. |
December 5, 2023, 03:14 PM | #11 |
Senior Member
Join Date: March 8, 2001
Location: Deep South Texas
Posts: 1,670
|
Absolutely contact them. They will want the lot number from the box as well.
__________________
To be vintage it's gotta be older than me! |
December 5, 2023, 04:48 PM | #12 |
Staff
Join Date: March 11, 2006
Location: Upper US
Posts: 28,871
|
welcome to TFL
Welcome Marine Dad!
Absolutely contact the ammo maker, and absolutely provide them with the lot # of the ammo. This is the second squib reported on this forum from the same maker and the same ammo. The lot# of the ammo you used is very important to the trouble shooting process. It will tell the factory if the problem exists in more than one batch. If your lot# is the same as the other lot# that had a squib, whatever caused the problem in the loading process might be confined to just that one batch of ammo. But if the lot#s are different, then the problem is something systemic, and EVERY lot of that ammo is now suspect, and by extension, until the exact cause is found, every thing they produce is under suspicion.
__________________
All else being equal (and it almost never is) bigger bullets tend to work better. |
December 5, 2023, 06:54 PM | #13 |
Junior Member
Join Date: August 24, 2012
Posts: 3
|
I have already contacted them and had a very fast response from Rick requesting the lot#.
|
December 25, 2023, 10:48 PM | #14 |
Member
Join Date: November 30, 2012
Posts: 66
|
They owe way more than a refund.
You are helping them with a potential liability issue down the road...they should have, at least, sent you a couple boxes of their best ammo for your caliber and thanked you. |
December 25, 2023, 11:55 PM | #15 |
Senior Member
Join Date: June 26, 2002
Location: Michigan
Posts: 253
|
i agree with Blue1. 5 years ago I loaded up some "powderpuff rounds to practice with in my 642. They shot very nice like a 22lr. I decided to shoot some in my .357 Taurus 6.5"bbl. Before I knew what happened I stuck the first round halfway down the bbl and the second shot stuck between the cylinder and bbl. Needless to say I was very pissed at myself and nervous with what to do next. after an expensive removal my gun smith showed me the bbl and said it was slightly bulging but not enough to affect use of the Taurus, only that it may affect the value of my .357. if you removed the bullet yourself you should take your .38 to a smith for exam, and if it did bulge the bbl., that ammo company owes you a new bbl. JMHO
__________________
Livin in the woods...feelin mighty good. |
December 26, 2023, 01:01 PM | #16 |
Staff
Join Date: March 11, 2006
Location: Upper US
Posts: 28,871
|
Generally speaking, a squib does not bulge the barrel. The barrel is rarely harmed at all from a squib.
It is the firing of another round with the squib still stuck in the barrel that damages / destroys the barrel. It is the responsibility of the shooter to see that doesn't happen.
__________________
All else being equal (and it almost never is) bigger bullets tend to work better. |
December 26, 2023, 01:03 PM | #17 |
Senior Member
Join Date: November 13, 2022
Posts: 342
|
Hey 44AMP is it possible to bulge a barrel by pounding out a squib?
|
December 26, 2023, 09:52 PM | #18 | |
Staff
Join Date: March 11, 2006
Location: Upper US
Posts: 28,871
|
Quote:
It is possible you can drive the slug tighter against the barrel as you try to drive it out. It would depend on the bullet nose, construction and the size and construction of what you are using to drive it out. Wood is not usually a good choice. Nor are soft metal rods, especially if considerably smaller than the bore. (regular cleaning rod, = not the best idea) Never actually had to do it, personally, and have used a worm to pull soft lead from muzzle loaders. Different ballgame with copper slugs. Factory ammo? I'd hit up the maker for the gunsmith's charges to repair the gun that THEIR AMMO rendered inoperable. I would only do it myself as a last resort. Have had a couple over the years where the bullet just barely entered the barrel and stuck, those I have popped out without any trouble. If it is a full bullet length or more into the barrel, take it to a smith, let him earn his keep.
__________________
All else being equal (and it almost never is) bigger bullets tend to work better. |
|
December 27, 2023, 12:33 AM | #19 |
Senior Member
Join Date: June 26, 2002
Location: Michigan
Posts: 253
|
44 amp said: "Generally speaking, a squib does not bulge the barrel. The barrel is rarely harmed at all from a squib."
With plated bullets it's a totally different situation. 44 amp said: "It is the firing of another round with the squib still stuck in the barrel that damages / destroys the barrel. It is the responsibility of the shooter to see that doesn't happen." Thanks for the cheap shot Mr. 44 Amp. The rounds shot fine out of my snub i had no reason to believe they wouldn't shoot well out of my 6.5 bbl.
__________________
Livin in the woods...feelin mighty good. |
December 27, 2023, 08:38 AM | #20 |
Staff
Join Date: February 12, 2001
Location: DFW Area
Posts: 25,005
|
I doubt any offense was intended. The point is that it's not really the squib that does the damage, it's firing another round into the lodged bullet. And further that the only sure way to prevent that from happening is for the shooter to detect the fired squib and stop shooting.
__________________
Do you know about the TEXAS State Rifle Association?
|
December 27, 2023, 03:10 PM | #21 | |
Staff
Join Date: March 11, 2006
Location: Upper US
Posts: 28,871
|
No offense or cheap shot was intended, and it never occurred to me that you might think so.
It doesn't matter what gun it is, if you get a squib, it is always on the shooter to recognize that and stop shooting before firing another round. Quote:
I don't see it.
__________________
All else being equal (and it almost never is) bigger bullets tend to work better. |
|
December 28, 2023, 02:16 PM | #22 |
Junior Member
Join Date: August 24, 2012
Posts: 3
|
Just saw on another forum where the shooter had a squib using the same Ammo Inc 125 gr. 38 special load. After some research, this company is well known for it's squib loads in 9mm also.
|
December 28, 2023, 05:36 PM | #23 |
Staff
Join Date: March 11, 2006
Location: Upper US
Posts: 28,871
|
Sounds like an excellent reason to not purchase their ammo.
__________________
All else being equal (and it almost never is) bigger bullets tend to work better. |
December 28, 2023, 05:59 PM | #24 |
Senior Member
Join Date: November 13, 2022
Posts: 342
|
Squibs are real dangerous and they scare the heck out of me. A man in an adjacent lane fired multiple squibs into the same revolver, it is an easy mistake to make at a Loud Indoor Shooting Range. Is that even recoverable from? Does a gunsmith drill that out with a fixture? Can you heat up the barrel and melt them out or would that destroy the steel in the guns barrel and frame?
|
December 28, 2023, 07:00 PM | #25 |
Staff
Join Date: February 12, 2001
Location: DFW Area
Posts: 25,005
|
Getting even one squib round out of a barrel can be quite a difficult process. See this thread:
https://thefiringline.com/forums/sho...d.php?t=617166 If the barrel is damaged, it might be easier to just replace the barrel. If not, it might be possible to remove the bullets, but I imagine that the 'smith would charge quite a lot for the operation and might caveat the whole deal by saying he wouldn't guarantee that the barrel would survive intact.
__________________
Do you know about the TEXAS State Rifle Association?
|
|
|