fixed sight single action revolver

bobn · July 21, 2007, 09:45 PM

hey guys, shot some cowboy action today with my awa revolver. it shoots four inches to the left and six inches low. could you guys guide me which way to file the rear sight notch and the front post? distance is 7 yards, caliper is 45 colt, barrel is 4 5/8s, thanks bobn

Tom2 · July 21, 2007, 10:32 PM

I thought the procedure on a single action like that is to file down the front sight a bit to raise the group and have a gunsmith rotate the barrel slightly to cant the front sight right or left to move the groups. If it shoots that far off at 7 yards though, you got a problem, I think. That is way out of the ballpark and I might send it back to the mfr. or something. If it was that far off at 25 yards, I could see making adjustments, but that close, something must be out of whack in my opinion. I would think you could shoot it closer than that without sights at 7 yards.

**44 AMP** · July 22, 2007, 06:08 PM

try some different ammo. Try a bunch of different loads. You may just find one that hits close to point of aim for your gun.

I don't like to file sights, it is a permanent solution to what is usually a temporary problem. try a different brand of ammo. A different bullet weight, a different velocity. Somewhere out there is a combination that will cure your problem.

Or, it also could be you,....low and left could be a problem with your grip and trigger squeeze, not your gun and ammo. Have someone else shoot your gun and ammo, and see how they do. if they don't go low and left, the gun doesn't need work, you do.

bobn · July 22, 2007, 08:47 PM

thanks for reply. i shoot a berretta stampede in the right holster, awa in left. cannot miss with stampede, might need another one. bobn

Harry Bonar · July 23, 2007, 03:52 PM

Sir:
44AMP just may have the answer!
If you're a right handed dude you will have the tendency to pull low and to the left but I don't think you're doing that since the other gun shoots great.
If, the bbl is in the frame straight (I've found lots that aren"t) and the notch is centered in the frame and the front sight is centered I would not turn the bbl. I think 44AMP has that answer. If something is not out of line I've found the factory bbl. crown off alot. It is normal with a fixed sight colt to hit low - and most, with your load will need to be filed down.
It has been my experience that the Italian colt replicas have several of these things off - in which case I'd return the revolver to the dealer and get another one - they do vary!
Harry B.

bobn · July 23, 2007, 08:13 PM

Thanks Harry, bobn.

July 21, 2007, 09:45 PM	#1
bobn Senior Member Join Date: December 30, 2006 Location: midwest Posts: 1,120	fixed sight single action revolver hey guys, shot some cowboy action today with my awa revolver. it shoots four inches to the left and six inches low. could you guys guide me which way to file the rear sight notch and the front post? distance is 7 yards, caliper is 45 colt, barrel is 4 5/8s, thanks bobn

July 22, 2007, 06:08 PM	#3
44 AMP Staff Join Date: March 11, 2006 Location: Upper US Posts: 30,465	Before you file anything try some different ammo. Try a bunch of different loads. You may just find one that hits close to point of aim for your gun. I don't like to file sights, it is a permanent solution to what is usually a temporary problem. try a different brand of ammo. A different bullet weight, a different velocity. Somewhere out there is a combination that will cure your problem. Or, it also could be you,....low and left could be a problem with your grip and trigger squeeze, not your gun and ammo. Have someone else shoot your gun and ammo, and see how they do. if they don't go low and left, the gun doesn't need work, you do. __________________ All else being equal (and it almost never is) bigger bullets tend to work better.

July 23, 2007, 03:52 PM	#5
Harry Bonar Senior Member Join Date: December 5, 2004 Location: In the Vincent, Ohio general area. Posts: 1,804	45 Colt Sir: 44AMP just may have the answer! If you're a right handed dude you will have the tendency to pull low and to the left but I don't think you're doing that since the other gun shoots great. If, the bbl is in the frame straight (I've found lots that aren"t) and the notch is centered in the frame and the front sight is centered I would not turn the bbl. I think 44AMP has that answer. If something is not out of line I've found the factory bbl. crown off alot. It is normal with a fixed sight colt to hit low - and most, with your load will need to be filed down. It has been my experience that the Italian colt replicas have several of these things off - in which case I'd return the revolver to the dealer and get another one - they do vary! Harry B.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

July 21, 2007, 10:32 PM	#2
Tom2 Senior Member Join Date: June 23, 2004 Location: Ohio Posts: 5,676	I thought the procedure on a single action like that is to file down the front sight a bit to raise the group and have a gunsmith rotate the barrel slightly to cant the front sight right or left to move the groups. If it shoots that far off at 7 yards though, you got a problem, I think. That is way out of the ballpark and I might send it back to the mfr. or something. If it was that far off at 25 yards, I could see making adjustments, but that close, something must be out of whack in my opinion. I would think you could shoot it closer than that without sights at 7 yards.

July 22, 2007, 08:47 PM	#4
bobn Senior Member Join Date: December 30, 2006 Location: midwest Posts: 1,120	thanks for reply. i shoot a berretta stampede in the right holster, awa in left. cannot miss with stampede, might need another one. bobn

July 23, 2007, 08:13 PM	#6
bobn Senior Member Join Date: December 30, 2006 Location: midwest Posts: 1,120	Thanks Harry, bobn.