Python 'smith?

bk40 · October 30, 2000, 05:39 PM

Can anybody point me towards a smith who is known for top quality work (particularly action jobs) with the Colt Python?

Dave Clements, well known for his big bore revolvers, lives only an hour from me. Unfortunately, he don't do Colts

The gang over at 1911forum highly recommended Reeves Jungkind... a top 100 smith per Am Handgunner

his contact is:
REEVES C. JUNGKIND
5001 Buckskin Pass
Austin, TX 78745
(512) 442-1094

I personally have never heard of him, so can anyone shed any light on Mr Jungkind's work or can recommend any other pistolsmiths?

TIA

JoeHatley · October 30, 2000, 09:09 PM

Bill Laughridge at www.cylinder-slide.com does world class work on Colts.

Good Luck...

Joe

------------------
Go NRA

Al Thompson · October 30, 2000, 09:38 PM

Not sure if Reeves is still accepting work. Ayoob had an article about him several years ago and mentioned that he only works on new (NIB) guns. Worth a call..

Another one is George Wessinger in Chapin SC. He does good work, still a one man shop though. (not fast) He is also an AH 100 member. Number is (803) 345-5677.

Giz

**4V50 Gary** · October 31, 2000, 12:45 AM

Bob Dunlap who is somewhere in Oregon. He was my instructor at LE Armourers' School (Susanville, CA). He made those AGI tapes.

Check out this old thread on Pythons. I think you will enjoy it:
http://www.thefiringline.com/NonCGI/...ML/000425.html

[This message has been edited by 4V50 Gary (edited October 30, 2000).]

bk40 · October 31, 2000, 03:49 AM

Thanks for the responses everyone! Got some good tips also over at John Taffin's site. Those mentioned were Fred Sadowski (deceased), Jerry Moran (unavail now), Reeves Jungkind, Walt Sherman and Jim Rose. Consesus seems that Reeves is the best IF you can obtain his services.

Thanks again / bk

October 30, 2000, 05:39 PM	#1
bk40 Senior Member Join Date: January 12, 1999 Location: Mississippi Posts: 1,004	Can anybody point me towards a smith who is known for top quality work (particularly action jobs) with the Colt Python? Dave Clements, well known for his big bore revolvers, lives only an hour from me. Unfortunately, he don't do Colts The gang over at 1911forum highly recommended Reeves Jungkind... a top 100 smith per Am Handgunner his contact is: REEVES C. JUNGKIND 5001 Buckskin Pass Austin, TX 78745 (512) 442-1094 I personally have never heard of him, so can anyone shed any light on Mr Jungkind's work or can recommend any other pistolsmiths? TIA

October 30, 2000, 09:09 PM	#2
JoeHatley Senior Member Join Date: July 2, 1999 Location: Iowa Posts: 2,135	Bill Laughridge at www.cylinder-slide.com does world class work on Colts. Good Luck... Joe ------------------ Go NRA

October 30, 2000, 09:38 PM	#3
Al Thompson Staff Alumnus Join Date: May 2, 1999 Location: South Carolina Posts: 3,611	Not sure if Reeves is still accepting work. Ayoob had an article about him several years ago and mentioned that he only works on new (NIB) guns. Worth a call.. Another one is George Wessinger in Chapin SC. He does good work, still a one man shop though. (not fast) He is also an AH 100 member. Number is (803) 345-5677. Giz

October 31, 2000, 12:45 AM	#4
4V50 Gary Staff Join Date: November 2, 1998 Location: Colorado Posts: 22,287	Bob Dunlap who is somewhere in Oregon. He was my instructor at LE Armourers' School (Susanville, CA). He made those AGI tapes. Check out this old thread on Pythons. I think you will enjoy it: http://www.thefiringline.com/NonCGI/...ML/000425.html [This message has been edited by 4V50 Gary (edited October 30, 2000).]

October 31, 2000, 03:49 AM	#5
bk40 Senior Member Join Date: January 12, 1999 Location: Mississippi Posts: 1,004	Thanks for the responses everyone! Got some good tips also over at John Taffin's site. Those mentioned were Fred Sadowski (deceased), Jerry Moran (unavail now), Reeves Jungkind, Walt Sherman and Jim Rose. Consesus seems that Reeves is the best IF you can obtain his services. Thanks again / bk