![]() |
![]() |
#1 |
Senior Member
Join Date: December 10, 2012
Posts: 6,187
|
Remington v3
Can anyone give me experiences with the reliability of the v3?
|
![]() |
![]() |
#2 |
Junior Member
Join Date: September 7, 2018
Posts: 12
|
I have several thousands rounds through both a walnut and synthetic model with no FTF or FTE, they are good guns and can run long and dirty between cleanings if that's your thing.
|
![]() |
![]() |
#3 |
Senior Member
Join Date: February 11, 2007
Location: S. Florida
Posts: 280
|
I have a synthetic, and it has been extremely reliable with both 1 oz and 1 1/8 oz target loads.
|
![]() |
![]() |
#4 |
Senior Member
Join Date: August 19, 2008
Posts: 104
|
I literally came here to do some more research on this model myself. Planning on ordering one in just a few minutes based on everything I have read.
|
![]() |
![]() |
#5 |
Senior Member
Join Date: February 11, 2012
Location: Williamsburg, Va.
Posts: 1,528
|
I do not have one but if I were going to buy a new semi auto that or the Fabarm is the one I would get. I have not witnessed any issues with quite a few of these, and with any 'new to the owner' semi auto shotguns issues are fairly common.
__________________
What could have happened... did. |
![]() |
![]() |
#6 |
Senior Member
Join Date: December 10, 2012
Posts: 6,187
|
I am leaning heavily toward v3. It's narrowed down to V3 or Franchi Affinity.
|
![]() |
![]() |
#7 |
Senior Member
Join Date: February 11, 2012
Location: Williamsburg, Va.
Posts: 1,528
|
An inertia action versus a gas action. I would go gas, every time.
__________________
What could have happened... did. |
![]() |
![]() |
#8 |
Senior Member
Join Date: December 10, 2012
Posts: 6,187
|
Both inertia and gas have their merits. In terms of absolute reliability, inertia is the clear winner. Gas usually wins the shootability category.
|
![]() |
![]() |
#9 |
Senior Member
Join Date: February 11, 2012
Location: Williamsburg, Va.
Posts: 1,528
|
Based on issues with inertia guns I have personally observed I disagree with your absolute reliability assessment.
__________________
What could have happened... did. |
![]() |
![]() |
#10 |
Senior Member
Join Date: December 10, 2012
Posts: 6,187
|
The only inertia guns I have seen are Benelli and Franchi. I have never seen a non shooter caused issue with either.
When you get into low end inertia guns, I have no idea what problems might arise. |
![]() |
![]() |
#11 |
Senior Member
Join Date: February 11, 2012
Location: Williamsburg, Va.
Posts: 1,528
|
I have not seen an issue with a Franchi. Have seen several with Benellis.
__________________
What could have happened... did. |
![]() |
![]() |
#12 |
Senior Member
Join Date: December 10, 2012
Posts: 6,187
|
I broke down and bought the Walnut v3. Couldn't pass it up at $550.
|
![]() |
![]() |
#13 |
Senior Member
Join Date: December 10, 2012
Posts: 6,187
|
V3 is awesome. Fast, no recoil. My 8 year old shot half box handicap trap shells and kept saying it does not kick as much as his 20 ga.
|
![]() |
![]() |
#14 |
Junior member
Join Date: August 7, 2019
Posts: 19
|
$550 for the V3 strikes me as a good deal! Congrats. Range report as soon as.possible please.
|
![]() |
![]() |
#15 |
Senior Member
Join Date: December 10, 2012
Posts: 6,187
|
Range report. It runs anything you feed it. It is as good an automatic sporting clays gun as any I have shot. It is fast. You can easily put all 4 spent shells in the air at the same time. Recoil is almost non existent.
|
![]() |
![]() |
#16 |
Senior Member
Join Date: August 19, 2008
Posts: 104
|
I agree with your findings. I just tried mine out yesterday and did a side by side with a Mossberg 930. They both fed any loads I shot but the recoil was noticeably less with the Remington. I used loads from 1145 fps to 1300 fps, 1oz, 1-1/8oz, and 1-1/4oz loads.
|
![]() |
![]() |
|
|