The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Thread Tools Search this Thread
Old March 31, 2013, 12:31 PM   #1
Junior Member
Join Date: March 29, 2013
Posts: 2
Will Uberti parts work on my Euroarms Remington new model army

I baught a Euroarms Remington New Model army revolver and am having a difficult time finding extra cylinders. some one sayed parts from Euroarms and Uberti part will interchange. does any one know if there is any truth to this
blkpdrkid is offline  
Old March 31, 2013, 02:15 PM   #2
Doc Hoy
Senior Member
Join Date: October 24, 2008
Location: Chesapeake, VA
Posts: 5,105
Euroarms is Armi San Paolo.

You are best advised to call a parts house to verify compatability.

VTI, Dixie Gunworks, Winchester Sutler, or Deer Creek (Waldron Indiana)

I would talk to them on the phone. You may want to be prepared to tell them precisely how long your cylinder is.

My reading of history convinces me that most bad government results from too much government. Thomas Jefferson
Doc Hoy is offline  
Old March 31, 2013, 04:56 PM   #3
Senior Member
Join Date: March 26, 2010
Location: North Georgia
Posts: 128
Pietta BP cylinder was too long for my Euroarms. When I sent gun to Taylor's for a conversion cylinder they used a R&D made for a Pietta. Go figure.

Doc's advice should be heeded. Find a parts house, give precise dimensions, and ask their help.
"Peace is that brief glorious moment in history when everybody stands around reloading" - Thomas Jefferson
jlb43 is offline  
Old March 31, 2013, 05:08 PM   #4
Senior Member
Join Date: September 8, 2007
Location: Mississippi
Posts: 14,495
Nobody's parts are going to be drop in. You may find some that can be fitted with a little work.
Hawg is offline  
Old March 31, 2013, 05:39 PM   #5
4V50 Gary
Join Date: November 2, 1998
Location: Colorado
Posts: 19,531
Agree with Hawg. Plan to do some fitting and be grateful if it needs it. That way you can make sure it works right the first time.
Vigilantibus et non dormientibus jura subveniunt. Molon Labe!
4V50 Gary is offline  
Old April 1, 2013, 12:19 PM   #6
Senior Member
Join Date: November 18, 2010
Location: Orygun
Posts: 743
I had a Euroarms Remmie that had a horribly machined cylinder that locked up the gun after two shots due to extreme shaving of lead from poor allignment of the chambers with the barrel. A spare Uberti cylinder dropped right in and functioned well. The only difference was the gap was about .009" rather than my desired .003-.007".
With over 15 perCUSSIN' revolvers, I've been called the Imelda Marcos of cap & ball.
SASS#3302 (Life), SASS Regulator, NRA (Life), DGB#129
Wolverton Mtn. Peacekeepers (WA), former Orygun Cowboy (Ranger, Posse from Hell)
Hellgate is offline  
Old April 1, 2013, 08:17 PM   #7
Senior Member
Join Date: August 19, 2004
Posts: 6,481
Call VTI & discuss.
DPris is online now  
Old April 6, 2013, 03:56 PM   #8
Junior Member
Join Date: March 29, 2013
Posts: 2
ok thank you all your advice has been very helpful
blkpdrkid is offline  

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -5. The time now is 02:41 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent:
Contact Us
Page generated in 0.05938 seconds with 7 queries