The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Thread Tools Search this Thread
Old January 19, 2013, 08:06 PM   #1
Senior Member
Join Date: April 23, 2006
Location: South Texas
Posts: 1,907
Reloading with Berdan primers

I've noticed that PV carries and still has Berdan primers for sale. Have any of you tried depriming Berdan brass and reusing it? Is there a special tool that can deal with the tiny double holes? Can you drill them out from the primer side? Can one use Berdan primers in place of a standard, one hole primer?Thanks.
hodaka is offline  
Old January 19, 2013, 08:15 PM   #2
Senior Member
Join Date: January 8, 2005
Location: Missouri
Posts: 831
Never done it, but I've researched it when I was contemplating doing so for some European calibers.

You decap by piercing the primer from the back and prying it out with a dedicated berdan decapping tool. Or hydraulically. Fill with water, insert snugly fitting rod, whack with hammer, pressure pops the primer out the back. Messy. No way to do it with a decap pin as there is no way to precisely locate the 2 flash holes.

Primers are NOT interchangeable. Boxers have the anvil as an integral part of the primer, berdan have the anvil on the brass.
Mike40-11 is offline  
Old January 19, 2013, 08:16 PM   #3
Senior Member
Join Date: February 10, 2010
Posts: 720
Here is a short article that details decaping berdan type brass. Hope it helps.

Ive only played with it a little, and never really found a great way to deprime them myself.
Fishing_Cabin is offline  
Old January 20, 2013, 06:32 AM   #4
Senior Member
Join Date: April 23, 2006
Location: South Texas
Posts: 1,907
Thanks guys. Looks like a task that would need to be driven by desperation. I appreciate the quick info.
hodaka is offline  
Old January 20, 2013, 07:09 AM   #5
Senior Member
Join Date: February 20, 2000
Location: Colombia, SC
Posts: 608
Not really, the RCBS berdan decapping tool makes it easy. Just size without the decapping pin. My Lee hand primer primes berdan fine.
I don't have time for busy people
hagar is offline  
Old January 20, 2013, 09:22 AM   #6
Senior Member
Join Date: January 22, 2005
Location: Kentucky
Posts: 2,430
Geez... I tried de-capping Berdan primers probably 30 years ago, when a friend gave me about 500 foreign .30-06 cases, as I recall. It was a royal PITA to say the least. I did 100 or so, reprimed them then sold off the entire bunch for the scrap price of the brass. Hagar, points out that RCBS now has a decapping tool that works well so that may indicate that things have changed over the intervening years...or (LOL), Hagar has a higher tolerance for mind-numbing piece work than I offense is meant BTW...Rod
Cherish our flag, honor it, defend what it stands for or get the hell out. Our Freedoms are not free, they've been paid for many times over by heros in uniform. Far better men than I, died that we could be FREE.

USAF FAC, 5th Spl Forces, An Loc, lll Corps, RVN, 69-70, Vietnam Vet '69-'73
rodfac is offline  
Old January 20, 2013, 09:41 AM   #7
Senior Member
Join Date: September 15, 2007
Posts: 666
Easy way to deprimer berdan primed cases,works with berdan or boxer.
res45 is offline  
Old January 20, 2013, 10:32 AM   #8
Jim Watson
Senior Member
Join Date: October 25, 2001
Location: Alabama
Posts: 14,155
The only Berdan primers I ever fooled with were in some Kynoch .450 Express belonging to a friend. We clamped the sizing die in a vise, mouth up, and dropped a case into it. Then drove a common awl through the indent at a sharp angle so as to miss the integral anvil and just levered the primer out of the pocket. The same principle as the RCBS device, just with ordinary tools.

You can do it with hydraulics like Mike40 describes, you can even do it on the press with an expander plug. It is possible to bulge the brass beyond use if the primer is crimped or corroded really tight in the pocket.

res45s video does not emphasize it, but uses a balanced hydraulic surge that won't hurt the brass. There was an old Gun Digest or Handloader's Digest that showed a fancier set of tooling for the same job.

Getting into trivia and history, once upon a time, British shooters could support a domestic reloading tool industry. There were three Berdan decappers operating on completely different principles.

The Prime Hydro Punch had a water reservoir with plunger and a long nozzle that reached down into the case and set over the flashholes. A whack on the plunger forced the primer out with hydraulic pressure but with only a couple of drops of water released. Lots less messy.

The Prime Power Punch looked similar but the long nozzle set a fresh primer down against the flashhole from the inside. The exposed plunger was the head of a firing pin and a hit on it blew the Berdan primer right out into a shielded base. It cost you two primers per shot, one to shoot, one to decap, but was quick and dry. You could use a more common Boxer primer in the decapping operation. Noisy, though.

Prime or maybe Wamadet made a decapping spindle that went in the sizing die like a regular Boxer decapping assembly. For Berdans it had an offset decapping pin made of fine but strong piano wire. You left it loose in the threads and as you raised the press ram, mainipulated the head of the spindle to feel the pin into one of the flashholes. Then pull the press handle to decap like Boxer. Said not to work with crimped primers, the fine tip would just punch through.

But all that was in a bygone day and the old British tools largely forgotten.
I looked and the Wamadet seems to be back in production, but Prime is apparently long gone.
Jim Watson is online now  

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -5. The time now is 03:33 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2017 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent:
Contact Us
Page generated in 0.06431 seconds with 9 queries