The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Thread Tools Search this Thread
Old March 19, 2012, 05:07 PM   #1
Senior Member
Join Date: April 28, 2009
Posts: 162
Top 10 Gunsmithing tasks

What would the top 10 gunsmithing tasks be? As a gunsmith what tasks/projects are you asked to do the most?
4T4MAG is offline  
Old March 19, 2012, 05:26 PM   #2
Senior Member
Join Date: November 22, 2006
Posts: 2,770
Scope mounting
Trigger job
Barrel threading

At the top followed by everything else.
jmorris is offline  
Old March 19, 2012, 06:12 PM   #3
Senior Member
Join Date: February 13, 2006
Location: Washington state
Posts: 12,997
Repairs/parts replacement
Operating issues (FTF/FTE/misfires, etc)
Scope mounting/boresighting
Trigger installation/trigger jobs
Recoil pad installation
Wood refinishing
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Taylor Machine
Scorch is offline  
Old March 19, 2012, 06:37 PM   #4
Jammer Six
Senior Member
Join Date: April 3, 2005
Location: Seattle
Posts: 827
Brakin' out the Dremel an' havin' at that feed ramp!

Actually, anything that starts with the statement "my buddy did some work on this for me and..."
"Huh?" --Jammer Six, 1998
Jammer Six is offline  
Old March 19, 2012, 09:51 PM   #5
Senior Member
Join Date: January 19, 2007
Posts: 2,647
For me?

DCI (disassemble, clean, inspect)
Recoil pad/LOP
new bead/replace broken off bead
Drill and tap for scope mount (bolt action rifles, Savage 99's, etc)
cut and crown (rifles)
cut to 18.5" and install high vis bead (shotguns)
lengthen forcing cone/alter choke
trigger job (rifles, DA revolvers, 1911s)
beavertail on a 1911
silver solder front sight and reblue (1911s)
Wichita rear sight install (1911s)
Slopemeno is offline  
Old March 27, 2012, 11:32 AM   #6
Join Date: April 6, 2005
Posts: 27
Recoil pad installation and scope mounting are the bread and butter around here. Still a bit of rebluing, but not as much as previously.
wildfowl4444 is offline  
Old March 27, 2012, 12:16 PM   #7
Senior Member
Join Date: March 11, 2010
Location: South East Pa.
Posts: 3,364
I am pretty much out of it now, but over the years it changed a lot for me. You can see variation in the answers on this thread. A lot of things affect the type of work you do. Sometimes it is just the area you are in. A guy a few miles south of me is deep in a shotgun only area and does not do much rifle work at all. Changes in Game Laws, changes in gun laws, movies, a large influx of cheap rifles/ammo, and probably the most influential is magazine articles. I would say the #1 consistent job for me overall was checking out inherited, auction bought, or"The guy owed me money" guns. This covered handguns, rifles and shotguns. Other than that the job type frequency really changed a lot for me.
Gunplummer is offline  
Old March 27, 2012, 06:02 PM   #8
Senior Member
Join Date: September 16, 2009
Location: I live in the foot of the Green Mountains of Vermont
Posts: 1,599
Refinishing (Wood & Metal)
Recoil Pad Installation
Drill & Tap
Scope Mounting
Trigger adjustment & installation
Sighting In
oneoldsap is offline  
Old March 28, 2012, 12:35 AM   #9
Superhouse 15
Senior Member
Join Date: September 13, 2007
Location: Sunny Florida
Posts: 844
Revolver trigger work
Scope install/boresight/bases/mounts
Semi auto trigger/action work
"I took this apart and cant get it back together, all the parts I could find are in this bag"
Change/zero sights (non-scope or red dot) including inserts
Touch up blue/rust removal
Glass bed and/or free float barrels
Butt pads and stock work
Shorten barrels on shotguns
Aftermarket parts builds (AR,10-22, AK, Siagas)
Superhouse 15 is offline  
Old March 30, 2012, 07:08 PM   #10
James K
Join Date: March 17, 1999
Posts: 24,279
At one time it was drilling and tapping for scopes. But today, almost all factory rifles come drilled and tapped, and ex-military rifles are collectors items, so that job is not called for as much. Same with shotgun recoil pads; once a staple of the gunsmith's work, lighter recoiling guns and factory pads have cut out a lot of that. Scope mounting and bore sighting are still common, but even those jobs are now usually of the DIY variety.

For the general gunsmith today, I think more exotic jobs, like machining muzzle brakes, glass bedding and free-floating, and trigger/safety installation and alteration are common.

Due to various pollution laws and OSHA regulations, few small gunsmith shops will do rebluing any more, so that is another bread and butter job that the nanny state has taken away from the average gunsmith.

Of course there is always the brown bag full of parts of the revolver "my kid took apart", but taking on those jobs can be tricky. The customer not only wants you to put the gun together, he wants you to make or find any necessary parts, like the hammer, trigger, and cylinder, and put them in for free as a goodwill gesture. And when you give back the gun with a bill for $75 - a third what the labor cost - he tells you that the "old POS" isn't worth that (you told him that at the beginning) and to put it in a dark place.

Jim K
James K is offline  
Old April 1, 2012, 05:28 PM   #11
Senior Member
Join Date: March 11, 2010
Location: South East Pa.
Posts: 3,364
Yeah, you are right on that one. "Nobody took this old double apart, something must have broken inside". Fresh scarring on the screws and bent springs inside.
Gunplummer is offline  
Old April 1, 2012, 05:33 PM   #12
Senior Member
Join Date: July 18, 2010
Location: Independence Missouri
Posts: 4,206
Which one of you fellas are interested in "truing" an old Mauser action, and rebarreling it?
Thanks for coming!
hooligan1 is offline  
Old April 2, 2012, 08:22 AM   #13
Senior Member
Join Date: April 25, 2010
Location: Arkansas
Posts: 3,309
"Hunting season starts tomorrow. I want this fixed by yesterday."
Rifleman1776 is offline  
Old April 2, 2012, 11:46 AM   #14
Double Naught Spy
Senior Member
Join Date: January 8, 2001
Location: Forestburg, Montague Cnty, TX
Posts: 11,649
One of my shooting buddies is a retired gunsmith. A lot of what has been listed so far are what he described his job being 90-95% of the time. It is what he calls "Gunsmithing Lite."

IIRC, his most numerous tasts were scope mounting, buttstock pads, cleanings (field and total take down), and trigger jobs. The number one complaint of his smithing concerned scopes. He would mount and bore sight the scopes and explain that the owner would need to refine the sighting at the range before hunting. The hunter would have a bad outing and return the gun complaining that it wasn't sighted properly...and it wasn't, but not because of the gunsmith's work. Either the hunter didn't finish properly sighting in the scope to the rifle or did so with one type/load/weight of ammo and hunted with something completely different.

Beyond these were often minor repairs and cosmetic enhancements.

He said that every now and then he would get in some challenging gunsmithing task, but by and large, the majority of what he did didn't utilize much of his training - hence the moniker of "Gunsmithing Lite."
"If you look through your scope and see your shoe, aim higher." -- said to me by my 11 year old daughter before going out for hogs 8/13/2011
My Hunting Videos
Double Naught Spy is offline  

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -5. The time now is 10:23 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent:
Contact Us
Page generated in 0.07340 seconds with 7 queries