The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Dave McCracken Memorial Shotgun Forum

Thread Tools Search this Thread
Old December 30, 2011, 08:36 PM   #1
Join Date: August 11, 2010
Location: Hoquiam, WA
Posts: 36
Help on this REMINGTON semi auto please.

Hello All,

I need disassembly instructions for removing the barrel of a Remington
Model 11 SPORTSMAN. (S203xxx)

Can anyone point me in the right direction ??

Someone 'Bubba'd" the barrel. the new owner asked me to "fix it and clean it up". My idea is to replace the 'boogered" barrel, and do a good reblue, no buffing, no refinish... !!

My internet search has been fruitless.

Razor740 is offline  
Old December 30, 2011, 11:38 PM   #2
Junior member
Join Date: June 23, 2009
Location: Orange County, CA
Posts: 2,149
Did you try Remington If that doesn't work you can mail this form to Remington
TheKlawMan is offline  
Old December 31, 2011, 04:37 AM   #3
Senior Member
Join Date: April 16, 2009
Location: Fort Worth, Texas
Posts: 194
This will get you close, you may have to use the cartridge shell stop to remove the breech block pin, it will make sense once you start the tear down. Also if the buttstock screw is hard to remove, try removing the 2 trigger guard screws first to relieve any tension on the buttstock screw. Goodluck and make sure you have the right screw drivers.

Browning Field Service Manual
Orphanedcowboy is offline  
Old December 31, 2011, 06:53 AM   #4
Senior Member
Join Date: July 1, 2011
Location: Good Ol' Wisconsin
Posts: 327

There ya go mac.
When I die better bury me deep, two .45s layin' at my feet,
An M16 across my chest, tell Chesty Puller I did my best
meatgrinder42 is offline  
Old January 4, 2012, 01:10 AM   #5
Join Date: August 11, 2010
Location: Hoquiam, WA
Posts: 36
Thanks Fellas,
My internet has been down for 3 or 4 days...
This info looks to be just what I need.
PS...I gots me a good set of hollow ground screwdrivers I keep hid from the wife.
Razor740 is offline  
Old January 4, 2012, 09:10 AM   #6
Senior Member
Join Date: December 31, 2011
Location: Vermont
Posts: 1,957
If the info is not what you need, all Browning A5's, Remington Model 11's of all flavors, and Savage 720's, 745's, 755's and 775's are the same as far as barrel removal goes...

Unscrew the magazine cap, remove the forearm forward, and simply slide off the barrel...

Take note of friction ring and spring placement for reassembly...

Magazine tube/friction ring interface should be run dry without oil...Friction rings are adjusted for light/heavy loads...

BTW...The Remington Model 11 'Sportsman' is simply a 3 shot version of the regular Model 11...No plug needed for waterfowling...
Salmoneye is offline  
Old January 4, 2012, 05:41 PM   #7
Senior Member
Join Date: October 27, 2005
Location: Crescent Iowa
Posts: 2,971

click on model 11 and download the PDF
markj is offline  
Old January 6, 2012, 01:04 AM   #8
Join Date: August 11, 2010
Location: Hoquiam, WA
Posts: 36
All of you were a great help.. Thanks..
Salmoneye: your directions were exactly what I was hoping for..
Razor740 is offline  

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -5. The time now is 07:12 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2016 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent:
Contact Us
Page generated in 0.06280 seconds with 7 queries