The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Thread Tools Search this Thread
Old June 22, 2010, 09:57 PM   #1
Join Date: January 11, 2005
Posts: 26
Uberti parts

I have a 1967 uberti 1851 round barrel. The hammer notches are worn out, and the hand and main spring broken. Will the parts kits that Cabela's offer fit, or must I order from VTI. VTI wants $46 just for the hammer. This gun belonged to my grandfather, and is quite special to me, but I just want to get it back to functioning properly. The wife has stopped my spending until the economy eases a little, so I must keep the price down.
drftrman is offline  
Old June 22, 2010, 10:06 PM   #2
Join Date: April 27, 2010
Posts: 93
The mainspring should fit fine, might need to be filed down at the tip a slight bit if it hangs up, should be easy to see by cocking back with the handle off.

The hammer *should* fit, my mid 70's Uberti hammer interchanges with my new peitta navy just fine.

The hand will need fitting, but that will probably be the case with any hand you buy
Kadmos is offline  
Old June 23, 2010, 06:50 AM   #3
Senior Member
Join Date: November 2, 2007
Location: Northern Orygun
Posts: 4,923
I would check Dixie Gun works. There prices are a lot lower than VTI. I would also order Uberti parts and expect to hand fit them.
madcratebuilder is offline  
Old June 23, 2010, 07:40 AM   #4
Junior member
Join Date: November 2, 2006
Posts: 908
Check Taylor's for parts too.
Also cheaper than VTI in some cases.

It's been my experience that parts for these pistols are never "drop-in" and amost always need to be fitted.

Fortunately, there are sites like this with alot of knowledgable folks who are willing to help you out should you have any questions.
Dino. is offline  
Old June 23, 2010, 09:31 AM   #5
Rebel Dave
Join Date: March 1, 2008
Location: Burlington Wis.
Posts: 41
Also About Cabelas as far as I know.. Theyre repair kits are for Piettas. That means a lot of fitting, if at all.

Rebel Dave
Rebel Dave is offline  
Old June 23, 2010, 09:44 AM   #6
Senior Member
Join Date: June 21, 2010
Posts: 190
You may want to contact Uberti directly for advice about the most suitable replacements.

It's true that I live in Italy and it's easier, but when I got a second hand Remington 1858 by Uberti that had the hammer and trigger bubba-ed (just shaking the gun was enough to fire it), a phone call was all I needed to know the codes of the parts needed for a refurbishment.

their contact is

kadima is offline  
Old June 23, 2010, 03:06 PM   #7
Fingers McGee
Senior Member
Join Date: March 19, 2008
Location: High & Dry in Missouri Ozarks
Posts: 2,083
Pietta parts generally do not fit on Uberti guns - and vice versa. You would be better served to buy Uberti parts for it & save yourself the aggravation of fitting them. Don't ask me how I know that.

Fingers (Show Me MO smoke) McGee - AKA Man of Many Colts - Alter ego of Diabolical Ken; SASS Regulator 28564-L-TG; Rangemaster and stage writer extraordinaire; Frontiersman, Pistoleer, NRA Endowment Life, NMLRA, SAF, CCRKBA, STORM 327, SV115; Charter member, Central Ozarks Western Shooters
Cynic: A blackguard whose faulty vision see things as they are, not as they should be. Ambrose Bierce
Fingers McGee is offline  
Old June 23, 2010, 05:26 PM   #8
Senior Member
Join Date: February 25, 2010
Location: Coyote Creak, SW Texas
Posts: 597

call or email Cimarron Firearms here

They may be able to help. They finish out many Uberti's and may have the parts you need or can direct you somewhere else.
Strive to live up to the opinion that your dog has of you.
twobit is offline  
Old June 24, 2010, 05:41 AM   #9
Join Date: January 11, 2005
Posts: 26
Thanks for all the suggestions, I will be calling dixie this morning. Might even email Uberti. I think I have the date correct, could someone look at the attached photo, and confirm please? It does not read Black Powder only any where on it. Only Cal. 36 and the proofs. Top of barrel reads Navy Arms Ridgefield NJ - Italy.

The hammer was really soft metal and the full cock notch wore out. Should I replace the trigger also? It doesn't seem to have any damage, but I do not want to ruin the new hammer or have an unsafe weapon.

(If these are too big or violate posting rules please advise)

As you can see my grandfather used this gun alot. He was a CW confederate reenactor back in the 70's.
drftrman is offline  
Old June 24, 2010, 05:56 AM   #10
Senior Member
Join Date: October 8, 2006
Location: Northern Michigan
Posts: 2,772
Yep. 1967.

mykeal is offline  
Old June 24, 2010, 05:59 AM   #11
Senior Member
Join Date: June 21, 2010
Posts: 190
Furthermore the "PN" stamp means "Polvere Nera" i.e. that the pistol was tested with Black Powder only.

Considering the low price of the trigger I'd change both hammer and trigger.

kadima is offline  

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -5. The time now is 09:14 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2017 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent:
Contact Us
Page generated in 0.07062 seconds with 7 queries