The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Thread Tools Search this Thread
Old June 9, 1999, 02:23 PM   #1
Join Date: October 27, 1998
Location: Bellevue, WA. USA
Posts: 31
I have a John Inglis High Power that isn't acting properly. With the hammer back, safety on, I press the trigger and the hammer falls to what looks like halfcock. Is the "safety" the problem? And if so will a Browning or FN safety work, or do I need a specific safety made for the Inglis High Power?
Thanks for the help,
Rodmann is offline  
Old June 9, 1999, 05:40 PM   #2
James K
Join Date: March 17, 1999
Posts: 24,160
Without examining the gun, I couldn't tell if the safety is defective or some other part is. Any HP safety should work, but for collectibility a genuine Inglis safety should be used. Check and go to the Other British Military Weapons forum. There is a discussion of the same point (by you?) and a fellow selling Inglis parts.

Any new safety will have to be fitted.


[This message has been edited by Jim Keenan (edited June 09, 1999).]
James K is offline  
Old June 10, 1999, 08:54 AM   #3
Senior Member
Join Date: January 29, 1999
Location: Texas
Posts: 1,796
As usual Jim is right on target, both as to interchangeability and the use of historically correct parts. I might add the following, in case it would be of interest, from R. Blake Stevens' book on the BHP.

In 1966 FN issued a "List of Assemblies and Parts of F.N. Origin Which Can Be Considered as Interchangeable with the Same of Canadian [i.e., Inglis] Manufacture." According to FN's list, the safety is interchangeable as an assembly, although "minor adjustment may be required." The safety assembly consists of the safety, safety stud, safety pin, and safety spring.

FN's list covers interchangeability only up to 1966. At that time, FN noted that "subsequent modifications may entail certain alterations." However, subsequent modifications, if any, must have made little or no difference, since Jim advises that any HP safety should work.
jimmy is offline  
Old June 10, 1999, 11:58 AM   #4
Join Date: October 27, 1998
Location: Bellevue, WA. USA
Posts: 31
Thanks for everyone's help on this matter. Since my Inglis in an import, I don't believe that installing a "old style" FN part will lower the pistol's value, though I believe that I have located an original Inglis safety. I recently purchased the pistol because it came with an original 1944 stock in excellent cond. The Inglis is very nice as well, all numbers match and the only import mark is stamped on the barrel. I will locate a new HP safety and have a qualified gunsmith install.
Thanks again.
Rodmann is offline  
Old June 10, 1999, 02:43 PM   #5
Rosco Benson
Senior Member
Join Date: October 20, 1998
Posts: 374
It sounds as if the current safety is no longer making good contact with the sear (pivoting it firmly into the hammer's full cock notch). It could be that the safety or sear are worn, it could be that the sear pin or the hole for it in the sear or the frame are worn. If the the sear and sear pin (and the holes) are okay and the sear is pivoting without excessive "wobble" or slop, then the problem might be able to be fixed by peening the stud on the thumb safety which engages the sear so as to displace some additional metal toward the sear so as to tighten up this fit.


P.S. - If you find yourself in need of a replacement safety, I have a mid-1970's blued Belgian one in the parts box you can have for $20 shipped (stud, pin, and spring installed)
Rosco Benson is offline  

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -5. The time now is 08:16 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2017 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent:
Contact Us
Page generated in 0.05587 seconds with 7 queries