The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Thread Tools Search this Thread
Old November 20, 1998, 01:56 AM   #1
Junior Member
Join Date: November 20, 1998
Posts: 5
I just purchased an 870 Express Magnum w/parkerized finish and fiberglass stocks. Also, got a TacStar mag extension (which came w/spring)when I bought the gun. Instructions state that the two small detents inside the tube must be filed down to function. Well, I ground them down w/the handy Dremel. The factory follower still seems to hang up sometimes near the front of the tube when the mag is full and causing a failure to feed. I ground the detents off and I don`t dare take any more metal off from inside the tube. I plan on getting a new high vis follower - are these any smaller in diameter. Anybody have similar problem - any suggestions would be greatly appreciated.
Chris is offline  
Old November 20, 1998, 04:21 AM   #2
Mac Scott
Join Date: October 6, 1998
Location: Cotati, CA USA
Posts: 37
I would guess that you've still got some "unremoved" metal within the end of the mag tube that is restricting movement of inserted rounds. The most normal problem here, when removing those damnable indentations that Remington insisted on adding, is failure to completely (and uniformly) remove all evidence of restriction.

More people get in trouble with Dremel tools and guns than any other combination of working tools I can think of. What you need to do is assure concentricity of the inside of the mag tube, something difficult, but not impossible, to do with a hand-held grinder. An adjustable reamer, set for the proper I.D. of the tube, would set up and maintain concentricity. Lacking such a device, a simple brake hone might also be used for the purpose, albeit with a major judiciousness in its application: Wouldn't take much with a hone to screw up and go through the thin walls of the tube.

Bottom line is that this really is something that can be done by the average home 'smith with the average shop tools, but it takes going low and slow for a while, trying and fitting until your shells are free within the tube. You can actually do it properly with your Dremel, just so long as you manually feel for high spots, relieve those as encountered, and proceed slowly and carefully. Best of luck.

Mac Scott is offline  
Old November 20, 1998, 05:04 PM   #3
Senior Member
Join Date: October 29, 1998
Location: mid-coast Maine
Posts: 545
I recently went through the same process on an 1100 - used a Dremel, fit the follower, grind, fit the follower, etc. Finally got it to work. The next week, I mentioned this whole process to my gunsmith- he said all you need to do is drill the detents out with a 1/4" drill and smooth up the burrs with the Dremel. He loves guys with Dremel tools.
motorep is offline  
Old November 20, 1998, 05:26 PM   #4
Junior Member
Join Date: November 20, 1998
Posts: 5
Thanks guys. I think I`ll use a combination of your suggestions - drill out the detents and use the brake hone to smoth out the inside. Mac, I used the brake hone earlier with fine stones-just used it on slow and only a little but worked nice. Yeah, believe me I GO SLOW WITH DREMELS - couldn`t take it if I screwed up a gun!
Chris is offline  
Old November 21, 1998, 05:13 PM   #5
Junior Member
Join Date: November 20, 1998
Posts: 5
As I said earlier, I took both of your suggestions - I drilled out the indentations w/ 1/4" drill then used the brake hone with fine (400 grit stones) on the inside of the tube. Smooooth! The spring was still binding when using the factory follower w/ 6 rounds in the tube and I couldn`t find an extended follower locally - but I did have a metal follower from an old shotgun that fit fine - used that for now and works w/100% reliability. I`m still going to order a Scattergun Technologies extended mag tube with kit(spring and high viz follower). To replace the TacStar one.

Thanks again guys - this is a great place; need advice, just ask and ye shall receive; get info or just be social.
Chris is offline  

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -5. The time now is 12:27 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent:
Contact Us
Page generated in 0.05207 seconds with 7 queries