The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Thread Tools Search this Thread
Old April 30, 2000, 08:45 AM   #1
Dave T
Senior Member
Join Date: April 16, 2000
Location: Mesa, Arizona
Posts: 1,241
I started to post this question in the handgun section but thought I might get more experienced and specific infor here.

Which is the best of the SAA copies in terms of apperance (fit & finish), reliability, durability, accuracy (like shooting where the sights point)? I know there only a couple (maybe 3) companies in Italy making these but I'm not sure who does the best job.
Dave T is offline  
Old April 30, 2000, 09:38 PM   #2
Ned Roundtree
Senior Member
Join Date: December 8, 1999
Location: Lexington, KY,USA
Posts: 738
I have owned and currently own some very nice guns manufactured by Uberti. Sometimes the quality, fit and finish required by the importing company may vary. But the overall gun is still manufactured by the same folks. Case in point, my wife's two Cimarron Lightnings. Imported by Cimarron from Uberti, beautiful guns very smooth, shooting point of aim. Then I have two Taylor & Co revolvers, also by Uberti, nickel plated but you can see a lot of the sanding marks under the nickel.The guns also shoot very nicely. Bottom line-I recommend Uberti made guns.
Ned Roundtree is offline  
Old May 1, 2000, 03:13 PM   #3
Bill Mitchell
Staff Alumnus
Join Date: October 15, 1998
Location: Roswell,GA
Posts: 433
Howdy Dave,

Uberti and ASM are the two companies that make SAA clones. It's my opinion that Ubertis are the better of the two. As far as the best of the lot,Cimmaron Model Ps are very highly regarded as fas as fit and finish.

Bellicose Bill
Bill Mitchell is offline  
Old May 23, 2000, 05:42 AM   #4
Senior Member
Join Date: March 8, 2000
Location: MA
Posts: 177
IMHO, the Ruger Vaquero is unrivaled for the things you list (reliability, durability and accuracy). As far as appearance, it's dimensions are slightly larger than the original Colt.
Malpaso is offline  
Old May 23, 2000, 09:15 AM   #5
Junior member
Join Date: January 5, 1999
Location: Springfield, Missouri
Posts: 2,105
Ditto, ditto and ditto. The clones vary in price and perhaps quality from the low of the Liberty imported by KBI up to the high of US Patent Firearms. The Liberties have a dealer cost of only $209 (with brass backstrap and trigger guard) and don't look half bad. The USPA's are three times that amount. The best overall compromise is probably the Cimmaron, Navy Arms or EMF Dakota or Hartford.
The Vaquero is superior in terms of strength and servicability. They are less expesive than some of the copies but higher than the cheapies. However they lack the "feel" of the Colt/clone.
If you have the time to before your purchase your best bet would probably be to attend shows and look in shops until you find the one that "speaks" to you.


TFL End of Summer Meet, August 12th & 13th, 2000
Gunslinger is offline  
Old May 26, 2000, 07:35 AM   #6
Rusty S
Senior Member
Join Date: March 8, 1999
Location: Walker Lake, NV: Flyway of the Loons
Posts: 611
Hey "slinger"! Used to be you could get and fit some aftermarket grip frames ( it's confused in my mind, but XR3/ XR3RED ring a bell ) that i think were intended for the smaller 3 screw old frame but could be mated to the larger 2 pin new model one size fits all frame. Was I smokin' wacky terbacky or does that sound right to you? Can you still get and swap the old small XR3 frame with the new model eVACQUERator bulloney guns? They made a small frame Bisquit 32 H&R mag, then dropped it. Can they still be assembled fro rimfire guns? Rechambered to 32-20? 25-20? 5mm velo doggie? Must be time to craxh ...
Rusty S is offline  

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -5. The time now is 06:22 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2017 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent:
Contact Us
Page generated in 0.07232 seconds with 7 queries