|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
January 11, 2013, 03:56 PM | #1 |
Senior Member
Join Date: April 20, 2009
Location: High Desert Mountains CA.
Posts: 410
|
.36 Caliber Paper Cartidges???
Back in the 1980's I knew a guy who made theses little tamale looking things that he just dropped in the hole and fired them. It was charge and ball in a combustible paper.
Are they available??? |
January 11, 2013, 04:25 PM | #2 |
Junior member
Join Date: January 26, 2012
Posts: 1,066
|
Sure!
Gather powder, bullet, cigarette rolling papers, glue, and some saltpeter. Roll 'em up. There are plenty of places on the net to see how to do it. AFAIK they are not sold commercially. Willie . |
January 11, 2013, 05:33 PM | #3 |
Senior Member
Join Date: November 25, 2012
Location: Eaton Rapids, MI
Posts: 445
|
Tried this... LOVED the idea! spent a ton of time doing it... didn't work out all that well. Turned out to be a waste of time for me. Not saying it won't work, they didn't ignite very well. Took several caps sometimes to finally get them to fire.
Birch
__________________
Black Powder: Not because it is easy, but because it is hard, because that goal will serve to organize and measure the best of our energies and skills, because that challenge is one that we are willing to accept, one we are unwilling to postpone, and one which we intend to win... |
January 11, 2013, 05:55 PM | #4 |
Senior Member
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,177
|
I used tea bags. They worked every time but are a PITA to make. At least for me.
|
January 11, 2013, 06:43 PM | #5 |
Senior Member
Join Date: September 28, 2008
Posts: 10,442
|
For pistol and revolver, it's easier to just put the pre-measured powder and ball in small containers and then dump the contents down the barrel or in the chambers.
The containers can be ordinary paper tubes, since they're not going in the gun.
__________________
Walt Kelly, alias Pogo, sez: “Don't take life so serious, son, it ain't nohow permanent.” |
January 11, 2013, 06:54 PM | #6 |
Senior Member
Join Date: April 3, 2011
Location: to close to other houses
Posts: 1,176
|
Ah but that wouldn't be historical fun
Potassium Nitrate...hot water, correct size dowel rod and cigarette papers. You need to be extra careful if you've never done this. These have a chance of leaving smoldering traces of the papers in the chamber which could ignite the next cartridge you load. Causing obviously hand/finger damage or removal. I make them up un-nitrated for ease of caring a cartridge box full...bite (or rip off ) the powder end, the place the bullet over the chamber for ramming... ripping off the remaining paper of as you seat the ball. Last edited by BerdanSS; January 11, 2013 at 07:00 PM. |
January 11, 2013, 06:59 PM | #7 |
Senior Member
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,177
|
With tea bags you don't need the nitrate. They're porous enough for the cap to blow through and they burn clean
|
January 11, 2013, 07:02 PM | #8 |
Senior Member
Join Date: April 3, 2011
Location: to close to other houses
Posts: 1,176
|
can you buy empty bags hawg....or you empty a bunch while watching Gettysburg (that would be my preferred method)
|
January 11, 2013, 07:19 PM | #9 |
Senior Member
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,177
|
I just bought cheap tea and dumped it. I disremember how many 44 cartridges you get out of a box but its a lot of them. I think I got four cartridges from each flo thru bag but I didn't try to optimize.
|
January 11, 2013, 07:28 PM | #10 |
Senior Member
Join Date: February 15, 2011
Posts: 277
|
I was thinking about these also, have not done much work on it, You can tell as you hear this question, But what do you mean by Nitrating and un-nitrated.. ???? And how does one Nitrate these??? And what does it mean it I am carrying them around either way..???
Last edited by indy1919; January 11, 2013 at 07:35 PM. |
January 11, 2013, 07:49 PM | #11 |
Senior Member
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,177
|
Dissolve potassium nitrate(KNO3) in water. Soak your paper and hang it up to dry. It helps it burn easier.
|
January 11, 2013, 09:11 PM | #12 |
Senior Member
Join Date: April 3, 2011
Location: to close to other houses
Posts: 1,176
|
And the un nitrated would be just regular papers with the powder on one end, a lead ball or conical bullet on the other with a thread tide between them. I do them like this as an alternative to using the plastic tubes. It keeps a ball and powder charge ready and neatly in the cartridge box...just rip the paper on the powder end and dump it in. Then rip off the rest of the paper from the ball and seat it. While it does the same thing as the plastic "speed tubes", it looks more "historical" than the plastic ones and honestly.....I like making them while I watch movies
like so... I do apologize as these are really rifle cartridges...but you get the idea. |
January 11, 2013, 09:17 PM | #13 |
Senior Member
Join Date: April 3, 2011
Location: to close to other houses
Posts: 1,176
|
duelist1954 did a really cool video (as are all of Mike's moving pictures) shooting an 1860 Army with pre made combustible paper cartridges he got some place. Wish I knew where he got them and if I could buy them...they are really cool. They were even in a period style paper carton.
|
January 11, 2013, 10:15 PM | #14 |
Senior Member
Join Date: February 15, 2011
Posts: 277
|
Thank you Brendanss.. I was trying to remember where I had seen those packs of paper shells from . Now those were a true work of art..
|
January 12, 2013, 01:57 AM | #15 |
Senior Member
Join Date: January 19, 2007
Posts: 2,663
|
I made them for my .45 single-shot muzzle loader, and they worked fine. First time, every time.
I made them with Zig Zags, formed over a mandrel to make them consistent sized. Lick them, roll, twist off the med, pur in 40 grains of Pyrodex, twist the end. Tiny dabs of white glue to keep the ends together. |
January 12, 2013, 02:23 AM | #16 |
Senior Member
Join Date: July 11, 2012
Location: Central Texas
Posts: 140
|
I used zigzags for my Walker. Used an old bolt I had in the garage.
First, rolled the paper with just the ball at one end then inserted bolt and continued as if rolling a cig. Did make sure bolt diameter was less than ball. Added 30gr pyrodex, twisted the hell out of powder end. Bit the tail before placing into cylinder. rammed the HELL out of the ball and I got what I believe was a faster ignition. It's very time consuming but fun when time permits.
__________________
"Why Johnny Ringo, you look like somebody just walked over your grave." |
January 12, 2013, 11:09 AM | #17 |
Senior Member
Join Date: November 18, 2010
Location: Orygun
Posts: 868
|
Here's just one of many sources from googling "empty tea bags"
http://www.herbco.com/p-1090-press-n...-x-275-in.aspx When I was using my cig paper cartridges I always kept a pair of tweezers handy to dig out unburnt paper and visually inspected each chamber before reloading.
__________________
With over 15 perCUSSIN' revolvers, I've been called the Imelda Marcos of cap & ball. SASS#3302 (Life), SASS Regulator, NRA (Life), Dirty Gamey Bastards #129 Wolverton Mtn. Peacekeepers (WA), former Orygun Cowboy (Ranger, Posse from Hell) |
January 12, 2013, 05:57 PM | #18 |
Senior Member
Join Date: January 21, 2000
Posts: 1,345
|
Have not had a .36 for years but all I shoot in my .44s is paper loads. Bugler paper seems to work pretty well for me. The trick is to get a taper to the things and clip the tail off as short as you can after twisting it. With a good taper they split at the rear when seated and go off every time. Tried folding the rear like some do and had ignition issues.
|
January 12, 2013, 11:33 PM | #19 |
Member In Memoriam
Join Date: March 17, 1999
Posts: 24,383
|
BerdanSS's idea will work fine, but the original revolver cartridges didn't involve tearing anything. You just dropped the cartridge (shaped roughly like an ice-cream cone) into the chamber and rammed it. Ramming broke the paper, foil or skin (cartridges were made of all three materials) to expose the powder. Cap the nipples and away we go!
Jim |
January 13, 2013, 04:11 AM | #20 |
Senior Member
Join Date: October 1, 2004
Location: Remote Utah desert
Posts: 224
|
Sam Colt created the idea of combustible cartridges in his revolvers, back in the 1850s. He first used tin foil, instead of paper, for its waterproofness and durability.
However, it hindered ignition more than nitrated paper. Also, Colt had a problem finding quality tin foil in this country. Too much of it produced here had tiny holes that let powder leak. He ended up ordering tin foil from Germany, one of the more technologically advanced countries in the world at that time. This raised the cost of his cartridges, forcing him to use paper, or animal skin or gut. At one point, he mixed a thick liquid -- a colloidin -- with black powder and formed cones of propellant, to which the conical bullet was attached. A lot of different things have been tried. I used to make my own combustible cartridges, soaking onion skin paper in a solution of Saltpetre (potassium nitrate), then hanging the paper up to dry. This was also done by bookies, who kept notes on bets on such paper. When the coppers busted through the door, they only had to apply a cigar or cigarette to the piles of notes on their desk and the evidence went up in seconds. The combustible cartridges I made worked fine, but I decided long ago that it was more trouble than it was worth. I dispense from a flask into a smaller container, then pour from that into each chamber. Still, making your own combustible cartridges is a link to history, and there's always pride in making something yourself. Have fun with making your own. Just don't smoke or do it by candleight!
__________________
"And lo, did I see an ugly cat. Smoke. Brimstone. Holes in parchment. And this ugly cat was much amused." --- The Prophesies of Gatodamus (1503 - 1566) |
January 14, 2013, 12:38 PM | #21 |
Senior Member
Join Date: April 20, 2009
Location: High Desert Mountains CA.
Posts: 410
|
Thinking about the silky-style teabags to make charges for a .58 Zouave.....Think that would work?????
|
January 14, 2013, 06:23 PM | #22 |
Senior Member
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,177
|
I'm thinking those are made out of nylon. Not a good idea.
|
January 14, 2013, 07:13 PM | #23 |
Senior Member
Join Date: April 20, 2009
Location: High Desert Mountains CA.
Posts: 410
|
You may be right. But the paper tea bags would be great for .58 caliber rifle charges....
|
January 14, 2013, 07:19 PM | #24 |
Senior Member
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,177
|
Yeah, I've used them in mine.
|
January 29, 2013, 01:01 PM | #25 |
Senior Member
Join Date: August 30, 2010
Posts: 1,635
|
There are some videos on YouTube that show people making and shooting these. Most use cigarette rolling paper.
You may be interested in Dean Thomas' Round Ball to Rimfire Part 3. It details pistol ammunition. Early on, it was packaged in cartridges just like muskets - a small paper tube with a ball in it and powder, and you had to tear the tail off, pour the powder, extract the ball, and ram it home. There were numerous complaints, namely that it was hard to hit the desired cylinder bore with the powder pouring out of the torn-open paper. Later there were many variants of so-called combustible cartridges, made from a variety of materials and often varnished to give some level of waterproofness. In period testing it was often noted that the so-called combustible cartridges were not really combustible and the ash and residue was left in the chambers. If you are going to use "combustible" paper cartridges have a care when loading to make sure there are no burning embers left in your cylinder bores. Steve |
Thread Tools | Search this Thread |
|
|