|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
April 1, 2012, 10:57 AM | #1 |
Senior Member
Join Date: April 28, 2009
Posts: 162
|
Dial Vs. Digital Caliper & Micrometer
I have spoken to a few gunsmiths regarding digital Vs. dial calipers & micrometers. They are all from a "older manual machinist" generation. Being younger and from a CNC generation I am wondering why they would all recommend dial instead of digital.
|
April 1, 2012, 11:20 AM | #2 |
Senior Member
Join Date: January 27, 2010
Location: Norfolk, VA
Posts: 2,905
|
Although they're easier to read, digital readouts don't do anything critical that the dial readouts won't do, unless you're getting into fancy stuff like averaging multiple measurements and calculating standard deviation, or being able to temporarily re-zero the tool at some position other than "jaws closed" in order to directly measure the difference between two length.
You're also at the mercy of battery life, temperature drift in the electronics, and just a higher level of complexity in general. That being said, I'd be comfortable using a good-quality example of either type. |
April 1, 2012, 12:20 PM | #3 |
Member In Memoriam
Join Date: March 17, 1999
Posts: 24,383
|
I have used all of the above, and also vernier calipers, and now use digital for the simple reason that it is easier for these old eyes to read. There might be slight problems, but gun work does not require very high precision, and the digital caliper is plenty good enough.
As to batteries, there are two holes in the case for spares; I keep them filled. Jim |
April 1, 2012, 12:51 PM | #4 |
Senior Member
Join Date: January 20, 2009
Location: Amity Oregon
Posts: 791
|
I've tried them all at one time or another.
Micrometers---I like plain old mikes, with a tenths vernier on the barrel. Had digital and ones with analog "counters" on them, they are OK but they don't do anything a old school micrometer won't. Calipers: My 24" and 12" are vernier. I've also got a couple of 6" verniers, but they don't get used much. A good set of 6" Mitutoyo digitals gets the most use. Dial calipers: If you are in a CLEAN environment, go for it. Dials work off of a microscopic gear rack and a itty bitty spur gear. Sooner or later, if there is any dust/dirt/chips etc within 10 feet of the thing, a piece will get in the rack and when the spur hits it it will jump a tooth. You won't even know it did it until you try to fit two parts together and one part is off by .015" or so. I currently own ZERO dial calipers. |
April 1, 2012, 01:48 PM | #5 |
Senior Member
Join Date: January 5, 2007
Location: Smack Dab in the Middle of Nowhere.
Posts: 505
|
I prefer the "old fashioned" way in most things, including this.
__________________
"We will do this: we will hang together, we will keep our organization, our arms, our discipline, our hatred of oppression, until one universal shout goes up from an admiring age that this Missouri Cavalry Division preferred exile to submission, death to dishonor". General Joseph O. Shelby, CSA (1830-1897) The only Confederate General who refused to surrender himself or his 1,000+ "Iron Brigade". |
April 1, 2012, 08:59 PM | #6 |
Senior Member
Join Date: February 13, 2006
Location: Washington state
Posts: 15,248
|
40 years ago, a good set of dial calipers could easily cost you $100 or more. Nowadays you can get pretty good oned for about $30, OK ones for about $20, and cheap ones for about $12. Digital calipers are getting pretty cheap now too. That said, I use dial calipers and vernier calipers for most of my work.
__________________
Never try to educate someone who resists knowledge at all costs. But what do I know? Summit Arms Services |
April 1, 2012, 09:11 PM | #7 |
Senior Member
Join Date: December 26, 2004
Location: Louisville KY
Posts: 13,806
|
I used a cheap digital for a while but finally got tired of having to re-zero all the time. The dial I bought is much more 'repeatable' and reads a lot faster.
|
April 1, 2012, 11:58 PM | #8 |
Senior Member
Join Date: February 1, 2010
Posts: 363
|
"Dial calipers: If you are in a CLEAN environment, go for it."
Totally wrong. having worked in NDT in a shipyard envoriment, dial calipers are tougher that he thinks. The important thing is keep them clean and keep them in the box when not in use. |
April 2, 2012, 07:24 AM | #9 |
Senior Member
Join Date: March 11, 2010
Location: South East Pa.
Posts: 3,364
|
I hear you. I probably used a solid mic as much as a dial calipers. The calipers is for ruff-out stuff.
|
April 9, 2012, 12:36 PM | #10 |
Member
Join Date: September 29, 2008
Location: Buda, Texas
Posts: 22
|
When I was working in the oil industry, we had a few Russian engineers start work for the company, and they each had one-meter-long vernier calipers. Huge things, hefty and substantial, and measured only in millimeters, centimeters and decimeters. Those things spoiled me for any fancy-schmancy dial or digital calipers, and I came to really love working with them.
That said, none of these guys would part with their toys for any price, so I'm back to dial calipers, 12" or 24", which work just fine. |
April 9, 2012, 12:41 PM | #11 |
Senior Member
Join Date: December 20, 2007
Location: S.E. Minnesota
Posts: 4,720
|
I like dial calipers, but I currently don't have any, and the cheap digital that I bought at HF works shockingly well. My eyes aren't good enough for verniers anymore.
__________________
"Everything they do is so dramatic and flamboyant. It just makes me want to set myself on fire!" —Lucille Bluth |
April 9, 2012, 12:55 PM | #12 |
Senior Member
Join Date: September 6, 2007
Posts: 1,204
|
Digital!
|
April 10, 2012, 10:38 AM | #13 |
Senior Member
Join Date: February 9, 2008
Location: Puget Sound Washington
Posts: 1,553
|
I use a Frankford el cheapo digital at home. My big complaint is that the battery life just plain sucks. After using much higher quality tools at work for many years, I'm just about ready to buy a really nice set for home use.
When I do, it'll be digital.
__________________
"If someone has a gun and is trying to kill you, it would be reasonable to shoot back with your own gun." The Dalai Llama (5/15/01, The Seattle Times) "That rifle on the wall of the labourer's cottage or working class flat is the symbol of democracy. It is our job to see that it stays there." George Orwell |
April 18, 2012, 06:12 AM | #14 |
Senior Member
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,324
|
measured response
If I'm measuring 'stuff' I use an inexpensive dial caliper.
When I'm measuring 'important stuff' I use a quality ten-thou mike. None of my tools require batteries.
__________________
. "all my ammo is mostly retired factory ammo" |
April 18, 2012, 07:53 AM | #15 |
Senior Member
Join Date: November 11, 2006
Posts: 2,519
|
Use both mics & dial,..
an prefer either.
Electronic when first out were definitely "squirrelly". Last company supplied dials were "Fowler" and a 10-incher, to boot. Got tired of trying to stretch a 6" to 6"+. |
April 18, 2012, 08:21 AM | #16 |
Senior Member
Join Date: April 25, 2010
Location: Arkansas
Posts: 3,309
|
I have all three. The batteries on the digital keep going bad. The old-fashioned micrometer is OK but hard to handle and read. The dial is the one I reach for. Accurate, easy to read, no batteries.
|
April 18, 2012, 07:52 PM | #17 |
Senior Member
Join Date: February 27, 2011
Location: Michigan
Posts: 257
|
I personally like dial calipers over digital just for the sake of not having to rezero them. If I need to set a zero that is different than closed jaw, I just turn the dial and lock it. I have left my calipers just laying on the bridgeport table while hacking away and have not had any problems. the more expensive digital calipers are pretty good though and don't eat through the batteries.
The Micrometers I use are standard mics but I also use some with a number counter in them at work and like them too. The digital mics seem to bulky to hold them right, at least the ones I have used anyway. Like anything the more you pay the better the item, this is more true for digital then anything. You can get a cheap set and they will work fine but you will have to rezero more and burn through batteries more. |
April 20, 2012, 09:48 PM | #18 |
Senior Member
Join Date: December 4, 1999
Location: WA, the ever blue state
Posts: 4,678
|
Pin gauges come in .0010" increments in sets.
But you can buy pin gauges individually in between. I have some of these for using as a spud to dial in barrels. Identifying these without reading the engraved value, if you can beat machinists with micrometers, when all you have is dial calipers, you are good. What does is all mean? You may think that micrometers are more accurate than calipers, while that is usually true, there still is the advice, " Never bet on another man's game."
__________________
The word 'forum" does not mean "not criticizing books." "Ad hominem fallacy" is not the same as point by point criticism of books. If you bought the book, and believe it all, it may FEEL like an ad hominem attack, but you might strive to accept other points of view may exist. Are we a nation of competing ideas, or a nation of forced conformity of thought? |
April 21, 2012, 03:35 AM | #19 |
Senior Member
Join Date: April 28, 2000
Location: Mississippi
Posts: 705
|
At one time I wouldn’t even entertain the thought of using digital. Still don’t like ‘em but I broke down and bought a 6" set…. Only ‘cause I lose my reading glasses too much and can’t read the dial. Tools stay where they’re supposed to… friggin glasses sprout legs. The more I use digital, the more I hate ‘em … ‘cause they remind me that I need glasses and can’t find ’em. Getting old sucks and I’m not THAT old !
How’s this for a confession: I have a slide rule in the tool box that I still use. It don’t need no stinkin batteries either, but I still need my glasses with it.
__________________
Keep smiling ... it'll just make 'em wonder what you're up to... |
April 21, 2012, 12:25 PM | #20 |
Junior member
Join Date: November 12, 2000
Location: Colorado Springs, Colorado
Posts: 9,494
|
Digital isn't any more accurate than analog until you've spent thousands on your tool. I always use analog.
|
April 21, 2012, 02:26 PM | #21 |
Senior Member
Join Date: July 9, 2007
Location: Fort Pierce, Florida
Posts: 381
|
have used both-
digital is easier to read (fewer mistakes) but too many bad readings bad batteries, cheaply made, worn out way too soon causing inconsistant readings too many *** is going on heres I went back to dial, even the cheaper ones give a consitant reading I load for accuracy and when a bullet shoots best between 10 and 15 thou. off lands that is where I want it, with a case trimed to where I wanted it to be trimed |
April 21, 2012, 02:49 PM | #22 |
Senior Member
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,190
|
I went digital because I can't read a dial anymore. Have a hard enough time reading digital with glasses.
|
April 24, 2012, 08:33 AM | #23 |
Staff
Join Date: November 2, 1998
Location: Colorado
Posts: 21,841
|
I used vernier calipers until my eyes changed. I thought about dial but went digital. Big is easy to see.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe! |
April 24, 2012, 10:22 AM | #24 |
Senior Member
Join Date: April 4, 2012
Location: South Jersey
Posts: 2,217
|
I use calipers and mics daily. I prefer dial for checking a lot of work. I can read them faster. The digital has a slight delay and ofetn makes people second guess over a .0005 when in reality it is a matter of feel. If you buy either Fowler makes a reasonable priced product thats pretty good. I use Starret but be careful as they now have a plant in China and a lot of there price minded stuff is coming from that plant. Brown and Sharpe makes a great price minded 6" dial caliper. In a micrometer they are all good out of the box. I just started switching my personal stuff over to the Starret digitals and I am very impressed.
|
April 28, 2012, 04:51 AM | #25 |
Staff
Join Date: November 2, 1998
Location: Colorado
Posts: 21,841
|
Some Starrets are made in the Workers' Paradise now? Oh, the humanity!
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe! |
|
|