The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools Search this Thread
Old February 5, 2011, 10:59 AM   #26
dlb435
Senior Member
 
Join Date: January 26, 2009
Posts: 654
My reloading area takes up 25 square feet. (5'X5') That is enough space for two presses, shells, bullets, primers, powder, scales, press parts and loaded rounds. That also includes the space for me to work in. The reloading bench is 2'X4' and is just big enough to get the job done.
dlb435 is offline  
Old February 5, 2011, 11:16 AM   #27
duck911
Senior Member
 
Join Date: December 21, 2005
Posts: 256
My "bench" is a super-portable home made job that can be set up ANYWHERE.

I usually use it on the kitchen table:

__________________
--Duck911
duck911 is offline  
Old February 5, 2011, 02:11 PM   #28
COSteve
Senior Member
 
Join Date: September 6, 2009
Posts: 1,190
As far as a reloading bench is concerned, my 1½" thick, 6' x 2' top I added to this old desk is about as small as I'd consider efficient. I've found that I need to keep things neat to efficiently use the small space but after 135,000rds of 8 calibers, I'm happy with the layout. The other issue you'll need to address is where do you store all the other things you use like components, finished ammo, tumbler media, etc.?

__________________
Steve

“Remember, no matter where you go, there you are.” - Confucius
"When you find a find a big kettle of crazy, it's best not to stir it." - Dilbert
COSteve is offline  
Old February 5, 2011, 02:26 PM   #29
chris in va
Senior Member
 
Join Date: December 26, 2004
Location: Louisville KY
Posts: 13,629
I do it in my easy chair.
chris in va is offline  
Old February 6, 2011, 04:18 PM   #30
BigJakeJ1s
Senior Member
 
Join Date: August 8, 2005
Location: Arlington TX
Posts: 663
For a bench located up against two walls in the corner of a room, you need more bench area than one that is only up against one wall, and still more than a bench that is located in the middle of the room, away from any wall. Think about bench space in terms of accessible "frontage" space. I reload very easily on a bench that is only about 22" by 28", but I have access to all four sides (including the shelves below). Mine is on heavy duty casters, so it rolls out when I need it, and back into its corner when I don't.

Andy
BigJakeJ1s is offline  
Old February 6, 2011, 04:29 PM   #31
Zildjian
Member
 
Join Date: October 2, 2009
Location: Ballinger, Tx.
Posts: 47
Portable table

Heres mine built out of plate 5/16 steel and 2" pipe. It swivels back to front
or whichever station I need to work on. Pretty stable and works for me in my bedroom. Right now its handy because the weather outside is cold wet and nasty. Moved from my storage building inside.
Attachment 67120
__________________
I Dont know you....but I have met you 1,000 times before.

Last edited by Zildjian; February 17, 2017 at 03:31 PM.
Zildjian is offline  
Old February 6, 2011, 05:19 PM   #32
700cdl
Senior Member
 
Join Date: December 6, 2010
Posts: 216
After many years of having to keep my loading mobile and portable, I finally have a whole room dedicated to my hobby. I never realized just how much space it consumes until having the luxury to unpack it all, mount it all, and provide shelving to stock supplies and brass on. It's so nice to have everything ready to use and easily at hand.
700cdl is offline  
Old February 6, 2011, 06:19 PM   #33
sc928porsche
Senior Member
 
Join Date: May 29, 2008
Location: now living in alabama
Posts: 2,433
All the money I save on reloading 30-378, 300WM, 260 Rem, etc. is spent on 44mag, 9mm, and 45acp!!! Its not uncomon for me to go through a thousand rounds or so on a range day. Reloading just make your shooting hobby more enjoyable. Not only are you spending more time at the range, you get to spend a lot of time making up the ammunition. I find the reloading and shooting is much more enjoyable than bar hopping.
__________________
No such thing as a stupid question. What is stupid is not asking it.
sc928porsche is offline  
Old February 6, 2011, 07:09 PM   #34
JayCee
Senior Member
 
Join Date: March 20, 2001
Posts: 487
I've never liked the idea of a bench fully devoted to reloading. It takes up too much space that I've got other uses for and it looks untidy. I also don't like all my reloading gear bolted down, since I like to reload at the range:



Occasionally, I'll find myself at the cabin or someplace else where I want to be able to put together and test a few loads. For those times, I take along a portable kit consisting of a Lee hand press, Lee scale, Lee dippers, and an RCBS hand priming device.



This kit contains everything I need for first class reloads and packs into a Doskocil pistol case.
__________________
“You may all go to hell and I will go to Texas.” – David Crockett

“If I owned Texas and hell, I'd rent out Texas and live in hell.” - General Phillip H. Sheridan
JayCee is offline  
Old February 6, 2011, 07:25 PM   #35
WANT A LCR 22LR
Senior Member
 
Join Date: September 5, 2010
Posts: 389
My Lee 1000 is bolted to a short piece of 3" angle then clamped into the bench vise. This way it can be put away when not in use. In any event, be sure to have a surdy mounting with a progressive press as the operator must have good feedback. If mounted on a springy surface the operator will things like a flipped primer or other issue.
WANT A LCR 22LR is offline  
Old February 21, 2011, 08:22 PM   #36
sserdlihc
Senior Member
 
Join Date: December 10, 2008
Location: S.C.
Posts: 1,454
Shootin Chef I use a spare bedroom for my reloading. A friend gave me an old kitchen island with storage and drawers that I use for my work station. It worked out great and saved me alot of time constructing something from scratch. I have my Lee single stage mounted on it along with my powder measure.

One thing that I have learned is to save all the plastic jars you can, Jiff peanut butter jars, Dukes mayonaise jars and the like, make great containers to store tumbled brass.
__________________
Familiarity breeds contempt, while rarity wins admiration. Aupleius
If someone doesn't like you, that's their problem! Milton Childress
sserdlihc is offline  
Old February 22, 2011, 01:05 AM   #37
700sage
Member
 
Join Date: November 28, 2010
Location: Rio Rancho
Posts: 90
While it doesn't have to take up that much space I've found it's nice to have a dedicated space and some privacy when reloading. That's why I have a shed in the backyard that is dedicated to reloading. It's insulated and has a heater for the winter. I believe it's 14'X10' and I have a bench along both lengths. One is set up for reloading the other is set up for casting bullets. I also have many items that I just attach temporarily with a C-clamp. I can spend days in the shed just goofing off.
700sage is offline  
Old February 22, 2011, 08:20 PM   #38
Dave R
Senior Member
 
Join Date: January 7, 2000
Location: Idaho
Posts: 6,073
For the first several years I reloaded, I kept all my gear in a Rubbermaid tub, and just clamped the press to the picnic table outside, or the kitchen table inside, as weather permitted. So maybe 4 sq. ft.

Now I've graduated to a dedicated desk. Just a plain ol' used office desk, with the press clamped on it, and my gear in the drawers. So now, maybe 10 sq. ft.
__________________
I am Pro-Rights (on gun issues).
Dave R is offline  
Old February 22, 2011, 08:33 PM   #39
silvercorvette
Senior Member
 
Join Date: October 26, 2010
Location: Anderson SC
Posts: 466
This is as small as it gets, before I got this sears tool table I bought a Frankford arsenal table that cost a lot more than this but when it arrived from Midway it turned out to be a flimsy piece of plastic junk. I got this a long time ago but if I remember correctly it is rated to hold 300 pounds, I weigh about 250 and stood on it to test it, it is rock solid and I am pretty sure it cost less than half of the Midway bench

__________________
I am broke, I spent my money on fast cars, guns, reloading equipment and ammo, the rest my money was wasted on nonessential stuff
silvercorvette is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:14 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07323 seconds with 11 queries