March 15, 2018, 03:26 PM | #1 |
Senior Member
Join Date: February 23, 2017
Location: Colorado
Posts: 424
|
Stag Arms Blemishes
So with the current political climate (not a discussion starter, not the point of the post), and the urging of a good friend of mine, I am in process of possibly picking up a Stag Arms blemished upper + lower. No barrel, gas, stock.
My question is, have any of you bought any of these blemished parts before? What were your thoughts/opinions? |
March 16, 2018, 05:34 AM | #2 |
Senior Member
Join Date: January 4, 2016
Posts: 757
|
I've never bought stags blemishes parts but I do have a stag rifle. They are fantastic quality and as long as the stag warranty still applies (not cosmetic obviously) I wouldn't hesitate to buy one.
|
March 16, 2018, 07:07 AM | #3 |
Junior member
Join Date: February 2, 2010
Posts: 6,846
|
I don't know about Stag blems specifically, but most of the "blems" I've acquired seem to be finish variances. Too light or dark or slightly mottled. Since all the machining is done before the cosmetic finishing, shouldn't be any real functional issues. I doubt ANY maker is going to release gun parts that might have structural or fitment flaws.
As far as internals: internal parts are relatively cheap so even looking at "blems" would be counter productive. |
March 16, 2018, 10:01 AM | #4 |
Junior Member
Join Date: March 16, 2018
Posts: 2
|
We put a disclaimer in each blem product to cover any possible finish defect, but each product will function like new and maintain Mil-Spec standards if applicable. As Mobuck stated, most of the time these products are available it's because the dye might have been low when the anodize was applied. This would cause the color to be slightly off. While we've found a little oil will bring it right back to life, we don't want to risk selling it as 'new' and receive a return for a minor finish issue. Also, there are times where we find a small scratch somewhere on the receiver and don't want to sell it as 'new' for the same reasons.
|
March 16, 2018, 02:08 PM | #5 |
Senior Member
Join Date: February 26, 2012
Location: Kansas City, MO
Posts: 296
|
Welcome @StagArms, and thanks for the info!
__________________
-- Lee Bad decisions make good stories. |
March 16, 2018, 02:54 PM | #6 |
Senior Member
Join Date: March 2, 2014
Posts: 11,773
|
Don't know about stag--But I've bought several PSA blem receivers and even a complete blem firearm--I've never been able to decisively figure out what/where the blem was.
__________________
"Everyone speaks gun."--Robert O'Neill I am NOT an expert--I do not have any formal experience or certification in firearms use or testing; use any information I post at your own risk! |
March 16, 2018, 07:32 PM | #7 |
Senior Member
Join Date: January 4, 2016
Posts: 757
|
...I think I am star struck. Stag arms is in the building!
|
March 16, 2018, 08:25 PM | #8 |
Junior member
Join Date: February 2, 2010
Posts: 6,846
|
".I think I am star struck. Stag arms is in the building!"
I'm always pleased to see manufacturer input on the forums. Mostly, they're just guys like us but can offer some insight we may not have access to. |
March 16, 2018, 08:53 PM | #9 |
Staff
Join Date: November 2, 1998
Location: Colorado
Posts: 21,832
|
Nothing a can of paint can't hide.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe! |
March 16, 2018, 10:08 PM | #10 |
Senior Member
Join Date: August 26, 2016
Location: North Dakota
Posts: 1,636
|
Do a nice cerakote or Duracoat finish on it and not only is the "blemish" gone, but you have a nice custom finish.
As for the rifle, I used to have a stag model 2 I sold to my brother on the cheap as he wanted an AR but is on a tight budget. It ran just as flawlessly as my Daniel Defense or Noveski. I would rate them very highly. |
March 17, 2018, 07:04 AM | #11 |
Junior member
Join Date: February 2, 2010
Posts: 6,846
|
An AR is a TOOL for me. Tools don't have to be "pretty" or have evenly matched finishes IMHO. Even if it starts that way, it won't stay that way long if actually USED.
|
March 17, 2018, 09:01 AM | #12 | |
Senior Member
Join Date: March 2, 2014
Posts: 11,773
|
Quote:
__________________
"Everyone speaks gun."--Robert O'Neill I am NOT an expert--I do not have any formal experience or certification in firearms use or testing; use any information I post at your own risk! |
|
March 17, 2018, 11:03 AM | #13 |
Senior Member
Join Date: January 21, 2016
Posts: 629
|
I bought a blem stag 15 recently - was kinda an impulse buy while I was buying other stuff, "OK let's put that in the pile too" .. plastic on the hand guard has a little gap I think is what it is but maybe the finish is off a bit, don't know don't care price was great shoots fine.
|
March 17, 2018, 10:58 PM | #14 |
Junior member
Join Date: February 27, 2015
Posts: 1,768
|
Just a tip from someone that has suffered through AR-10 builds...
I recommend buying your BCG from the upper manufacturer, and most manufacturers don't play well with other makers on Upper/Lower fitment. Since there isn't a 'Standard' for AR-10 (like military set standards for AR-15s for years, and still pretty much does) AR-10 parts are rarely, if ever, Mix-&-Match. This isn't just Stag, it's every maker... |
March 19, 2018, 08:52 AM | #15 |
Senior Member
Join Date: February 23, 2017
Location: Colorado
Posts: 424
|
Thank you all. And HUGE thank you to Stag for the personal response!!! I'm excited to get it in.
Mobuck, I'm a little confused what you meant by "looking at 'blems' would be counter productive'"? |
March 19, 2018, 09:38 AM | #16 |
Junior Member
Join Date: March 16, 2018
Posts: 2
|
Appreciate the warm welcome!
|
March 19, 2018, 09:39 AM | #17 | |
Senior Member
Join Date: March 2, 2014
Posts: 11,773
|
Quote:
__________________
"Everyone speaks gun."--Robert O'Neill I am NOT an expert--I do not have any formal experience or certification in firearms use or testing; use any information I post at your own risk! |
|
|
|