The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools Search this Thread
Old January 19, 2011, 06:20 AM   #1
mametlynch
Junior Member
 
Join Date: January 19, 2011
Posts: 2
Strange magazine problem...

I have a gun some of you might be familiar with, and some not. It's a Yugoslavian TT-33 variant, called the Zastava M57. There's not much difference between it and the regular Tokarev pistol, except that it holds 9 rds of ammunition instead of 8.

The thing is, these magazines are really hard to find, and I don't want to risk breaking the only one I have.

The trouble is that when I shoot it, the magazine for some reason expands with tiny bubbles in front, right where each bullet goes. A tiny bubble outside for where each bullet is, and actually causes the magazine to get stuck inside the well. With a lot of pulling, I can painfully scrape the magazine out of the well, and hammer the bubbles down so that it will smoothly fit back in.

If anybody could help me figure out what the problem is, I'd really appreciate it.

I used 7.62x25 Romanian surplus ammo the last time I shot it. I clean it with Hoppes #9.
mametlynch is offline  
Old January 19, 2011, 08:33 AM   #2
Crapulence
Senior Member
 
Join Date: November 12, 2008
Location: Manly Flower Mound Texas
Posts: 126
That magazine issue seems really strange to me. Are the rounds dimpling the magazine metal from the inside? I haven't had my coffee yet but it would seem that altering a similar magazine would be the cheapest route to go. Here is a link for one conversion that seems straight forward.

Yugo-M57-tokarev-alternate-magazine-option
Crapulence is offline  
Old January 19, 2011, 05:48 PM   #3
James K
Member In Memoriam
 
Join Date: March 17, 1999
Posts: 24,383
Yes, bullet noses can dimple a magazine from inside. When the gun is fired, it recoils, but the cartridges in the magazine (obeying Mister Newton) try to stay where they are and slam into the front of the magazine.

Normally, pistol designers take this into consideration and either make the magazine thick enough, or harden the metal, to keep this from happening. But some magazine makers, especially after market makers, don't really care and their mags will dimple even, as the OP points out, to the extent of keeping the magazine from being inserted/removed. The problem can be exacerbated by use of hotter ammunition than the pistol was designed for.

The only solutions are to either find some lower power ammo or find a better magazine, if that is the factory original.

Jim
James K is offline  
Old January 19, 2011, 11:55 PM   #4
mametlynch
Junior Member
 
Join Date: January 19, 2011
Posts: 2
Thankyou for your replies,

I've actually seen the magazine solution for the M57, and although interesting, I'm not sure I have the tools for that.

I'm actually not particularly interested in firing this pistol very often, it is sort of just a novelty gun, but is there any way I can take the magazine I have to a shop and have it buffed out and re-coated with something to make it stronger?

Thanks.
mametlynch is offline  
Old January 20, 2011, 12:31 AM   #5
JohnKSa
Staff
 
Join Date: February 12, 2001
Location: DFW Area
Posts: 24,932
I don't know of any coating that would help.

Assuming it's made of decent steel, you might be able to find someone to heat treat it which could make it more flexible and less likely to dimple. But that's not a feature typically offered by local gunsmiths.
__________________
Do you know about the TEXAS State Rifle Association?
JohnKSa is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:41 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.06993 seconds with 8 queries