February 10, 2017, 06:28 PM | #1 |
Senior Member
Join Date: January 7, 2017
Location: Colorado
Posts: 272
|
Walker lever fix
Shooting a Walker often has the loading lever dropping at each shot. I noticed the lever on this one doesn't come up to the barrel so I knocked the lever spring out and filed the base down were the lever contacted it. Reinstalled it and now it lets the lever come fully up to touch the barrel. Shooting full loads today the lever stayed in place as it should. Easy fix.
|
February 10, 2017, 07:35 PM | #2 |
Senior Member
Join Date: January 7, 2012
Location: Auburn, AL.
Posts: 2,332
|
Do you have pictures of the modified area? Nice looking fix on that Walker!
I got one that has a little slack in the loading lever too.
__________________
. . . Have a Colt and a smile. |
February 11, 2017, 08:36 AM | #3 |
Staff
Join Date: November 2, 1998
Location: Colorado
Posts: 21,831
|
Ditto what Beagle333 asked.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe! |
February 11, 2017, 01:22 PM | #4 |
Senior Member
Join Date: January 7, 2017
Location: Colorado
Posts: 272
|
You can see on the first photo the spring base is convex and in this photo the base is flattened. This is were the lever was stopped and so the lump on the spring couldn't fit fully into the lever. Knocking the spring out allows the base to be filed then cold blued. when placing it back in just be sure to center it with the hole in the lever.
|
February 11, 2017, 07:22 PM | #5 |
Senior Member
Join Date: January 7, 2012
Location: Auburn, AL.
Posts: 2,332
|
I see! The base itself wasn't letting the loading lever come all the way up to the barrel. I'll have to check that on my Palmetto. Thanks!!
__________________
. . . Have a Colt and a smile. |
February 12, 2017, 11:33 PM | #6 |
Staff
Join Date: November 2, 1998
Location: Colorado
Posts: 21,831
|
Many thanks.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe! |
February 13, 2017, 09:50 AM | #7 |
Senior Member
Join Date: August 30, 2010
Posts: 1,635
|
Why did you have to remove the spring from the barrel to file the base down?
Steve |
February 13, 2017, 10:35 AM | #8 |
Senior Member
Join Date: January 7, 2017
Location: Colorado
Posts: 272
|
That's the easy way to do it. The spring taps out with little effort and then clamping the base in the vise allows a few strokes of the file with out worrying about scratching the barrel. As lazy as I am you can be sure I wouldn't do it if I thought there was a better way.
|
February 13, 2017, 12:09 PM | #9 |
Senior Member
Join Date: October 14, 2009
Location: San Diego County
Posts: 795
|
__________________
US Navy Retired,NRA Life Member,SASS member, Time magazine's Person of the Year 2006! |
February 13, 2017, 02:59 PM | #10 |
Senior Member
Join Date: September 28, 2008
Posts: 10,442
|
Hose clamp.
__________________
Walt Kelly, alias Pogo, sez: “Don't take life so serious, son, it ain't nohow permanent.” |
February 13, 2017, 05:50 PM | #11 |
Senior Member
Join Date: March 2, 2015
Posts: 380
|
Is that the tool that Doc Hoy was making?
__________________
"If you have to shoot, shoot! Dont talk" |
February 13, 2017, 09:32 PM | #12 | |
Senior Member
Join Date: March 20, 2011
Posts: 566
|
Quote:
|
|
March 18, 2017, 05:27 PM | #13 |
Senior Member
Join Date: February 12, 2009
Location: Butte, MT
Posts: 2,619
|
I shot my walker for the first time today. What a beast.... The recoil of full loads of 777 is NOT a problem ... It's the weight of the gun!!! Those guys must have been 'he-man' to shoot these revolvers off hand!! My forearms and wrists are already a little sore as I type this! I didn't count but I went through only around 30 rounds (3 cylinder full + then loading full loads only one chamber at a time like a single shot for fun). The lever only started to come down once. Shoots way high though. 15Ys was 4" high, but nice group off-hand for a BP revolver.
I didn't shoot my ROA but I did bring it along. After hefting the Walker, and then just picking up the ROA later... The over built ROA seemed light and fluffy!
__________________
A clinger and deplorable, MAGA, and life NRA member. When guns are outlawed, only outlaws will have guns. Single Action .45 Colt (Sometimes colloquially referred to by its alias as the .45 'Long' Colt or .45LC). Don't leave home without it. That said, the .44Spec is right up their too... but the .45 Colt is still the king. |
March 18, 2017, 10:07 PM | #14 |
Senior Member
Join Date: January 7, 2012
Location: Auburn, AL.
Posts: 2,332
|
Not unusual to be high at 15 yds.
From what I've read, they were sighted in to hit at 75 yards. Tons of fun though, aren't they!!
__________________
. . . Have a Colt and a smile. |
March 19, 2017, 12:54 PM | #15 |
Senior Member
Join Date: October 12, 2012
Location: Wyoming
Posts: 351
|
RClark
since these don't have adjustable sights you have to pick a range you want to zero in at. might be high at 15 and dead on at 45. so decide before filing etc, at what range do you want it to be poa - poi? If you are always going to shoot at 15 yd then adjust (file) the sights for that. actually in this case a taller front sight. Or the other option. LEARN WHERE THE GUN SHOOTS AT VARIOUS DISTANCES. then you adjust your aim to compensate I've done that with all my BP guns with none adjustable sights. Course I rarely shoot at paper targets anymore. My common target is a 4x4 by 8" long I drive a piece of rebar in the ground. I drill a hole in the end of the 4x4. set it on the rebar I now have a target 3 1/2" wide and 8 " high. If I only nick the edge, it will usually spin a little side ways. Now my width may be only 2 1/2' Learn where the pistol shoots. |
March 20, 2017, 09:28 AM | #16 |
Senior Member
Join Date: February 12, 2009
Location: Butte, MT
Posts: 2,619
|
Yep, it is fun... But not fun enough to make it my 'primary' BP revolver due to it's weight. I look at the Walker as experiencing a bit of history. Not one that I would pack into the field. I have my ROAs for 'general' purpose BP shooting. Much more enjoyable to shoot.
As for learning where the revolver shoots, that is why I start at 15Ys. Whether it shoots high or low, it is bound to hit the paper target (well, usually as I have shoot at least one revolver that missed the paper plate entirely at that distance!). Then backup to more normal shooting distances.... once you know where it is shooting. I was shooting steel at 25 to 70 yards at our range with it. It really knocks down the 25Y targets with authority.
__________________
A clinger and deplorable, MAGA, and life NRA member. When guns are outlawed, only outlaws will have guns. Single Action .45 Colt (Sometimes colloquially referred to by its alias as the .45 'Long' Colt or .45LC). Don't leave home without it. That said, the .44Spec is right up their too... but the .45 Colt is still the king. |
August 17, 2018, 01:33 AM | #17 |
Senior Member
Join Date: October 24, 2008
Location: Naples, Fl
Posts: 5,440
|
Yep
Just a brief comment after about three years absence. Making these clips from copper now. First steel version too hard on the blued finish on the pistol. Brass was too expensive to make. Selling them on the ebay. Production still too slow to do much volume. I am opening the bids at 9.00. They sometimes go for more.
Thought about a patent but it isn't worth the 800.00. Apparently a new Walker from Uberti now has a plastic clip supplied with the pistol. Did they steal my design or did I steal theirs? Steve (Maillemaker) is selling a 3d printed version on a bulk site. I think it is Shapeways. He and I worked together a little on the design and he has my full support. He is quite a craftsman and I admire him. Anyway, nice to be back among friends.
__________________
Seek truth. Relax. Take a breath. |
August 17, 2018, 11:29 PM | #18 |
Senior Member
Join Date: January 7, 2012
Location: Auburn, AL.
Posts: 2,332
|
Good to hear from you again Doc! I'm going for one of the copper ones too!
__________________
. . . Have a Colt and a smile. |
August 18, 2018, 04:18 AM | #19 |
Senior Member
Join Date: October 24, 2008
Location: Naples, Fl
Posts: 5,440
|
Beagle,
If you are interested you can PM me from this forum rather than wait it out over at the eVilbay.
__________________
Seek truth. Relax. Take a breath. |
August 18, 2018, 06:26 AM | #20 |
Senior Member
Join Date: August 12, 2009
Location: Athens, Georgia
Posts: 2,526
|
No matter how prepared the man, he can always use a rubber band.
|
August 18, 2018, 08:26 PM | #21 |
Senior Member
Join Date: October 24, 2008
Location: Naples, Fl
Posts: 5,440
|
You speak the truth, 2DO4T
It could easily be said that the tendency of the Walker to drop the loading lever is not much worse, or perhaps not even as bad as the tendency of Colts to swallow caps.
Mankind developed the "Colt wave" as an almost subconscious hand movement to rid the pistol of the cap. The wave has become an integral step in the firing sequence. Why not a similar action to deal with the dropped lever? So after firing, the shooter (assumed right handed) lowers the right arm pointing the muzzle toward the ground, bends the right elbow at a 90 degree angle (Walker trained safely down range) then cradles the pistol in the left palm with the thumb on the left side of the cylinder and the fingers touching the right side of the cylinder, making sure to retain a firm hold on the grip with the right hand. He (or she...after all, my academic expertise is in Human Resources Law.) then quickly slides the left hand forward along the frame and trigger guard and finally to the barrel, using the action to ensure the loading lever is still in the upright and locked position, or to return a dropped loading lever to its battery position. The action is complete when the shooter firmly wraps thumb and fingers around the hot barrel and listens for the reassuring click as the lever snaps into place. Call it the "Walker Squeeze". So the firing sequence becomes: 1. Cock 2. Aim 3. Fire 4. Walker squeeze 5. Cock 6. Colt wave 7. Aim 8. Fire This action might actually facilitate the Colt wave, since the first wave frequently fails to dislodge the offending cap fragment requiring a second action, the "Inverted revolver shake". As we all know, that shake performed using the five pound Walker requires two hands in all but the most robust of shooters. Don't forget to follow the shake with either one of two exclamations: 1. "Aaaaah, their it is!" or 2. "Com'on you *&^%$" generally prompting a second shake. . . . Sorry guys...Running a restaurant does nothing to abate an overactive sense of humor.
__________________
Seek truth. Relax. Take a breath. Last edited by Doc Hoy; August 20, 2018 at 04:08 AM. Reason: remove possibly offensive passage |
August 19, 2018, 10:48 AM | #22 |
Senior Member
Join Date: August 12, 2009
Location: Athens, Georgia
Posts: 2,526
|
: ) Nothing wrong with a sense of humor.
|
August 19, 2018, 12:10 PM | #23 |
Senior Member
Join Date: February 13, 2002
Location: Canada
Posts: 12,453
|
It was cold in February and March of last year.
__________________
Spelling and grammar count! |
|
|