The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools Search this Thread
Old August 25, 2012, 04:17 PM   #1
azmark
Senior Member
 
Join Date: August 26, 2007
Location: Palominas, AZ
Posts: 221
Green 'scrubby pads'

Has anyone tried the heavy duty green 3M cleaning pads to remove rust from blued surfaces? They have to be less abrasive than steel wool or even brass. The bluing is old and I want to avoid taking any of it off.
__________________
Mark Dickinson
USAF, Retired
azmark is offline  
Old August 25, 2012, 04:32 PM   #2
Wahoo95
Member
 
Join Date: February 19, 2007
Location: Charlotte, NC
Posts: 62
Here's a tip......heat the surface and apply Frog Lube. Allow it to soak in for 10min or so then polish the Froglube in with 0000 Steel Wool. It will remove all the rust and leave the metal/finish protected from rusting in the future.

Here's a pic of my Sister n Laws Bersa which should brought to me for cleaning after allowing it to get all rusty.



After



Blame any misspellings on Tapatalk
Wahoo95 is offline  
Old August 25, 2012, 04:43 PM   #3
azmark
Senior Member
 
Join Date: August 26, 2007
Location: Palominas, AZ
Posts: 221
I've never heard of frog lube. What is it and where can it be gotten.
__________________
Mark Dickinson
USAF, Retired
azmark is offline  
Old August 25, 2012, 05:06 PM   #4
'88Scrat
Senior Member
 
Join Date: July 11, 2011
Location: Kansas
Posts: 546
It stands to reason that the green scrub pads like Scotch Brite would remove rust. I work at a Home Depot and I rent out larger ones (like for a floor maintainer) for removing old glue and polishing floors all the time. They are best used when you want to get cleaning done without ripping up the vinyl. That said I have never used them for removing rust but I can see where they would work well. If you do use them let us know it turns out.
__________________
BOOM
'88Scrat is offline  
Old August 25, 2012, 07:11 PM   #5
Pahoo
Senior Member
 
Join Date: February 16, 2006
Location: IOWA
Posts: 8,783
Seeing is believing !!

I have used them and find that they are more abrasive than 0000 steel wool. Compare there action on a scrap piece of metal and confirm. Let us knwwhat you find. ..

Be Safe !!!
__________________
'Fundamental truths' are easy to recognize because they are verified daily through simple observation and thus, require no testing.
Pahoo is offline  
Old August 25, 2012, 08:07 PM   #6
Bill DeShivs
Senior Member
 
Join Date: April 7, 2006
Posts: 10,966
Scotchbrite will scratch steel!
0000 steel wool removes rust without Frog Lube or anything else.
__________________
Bill DeShivs, Master Cutler
www.billdeshivs.com
Bill DeShivs is offline  
Old August 26, 2012, 02:14 AM   #7
Slopemeno
Senior Member
 
Join Date: January 19, 2007
Posts: 2,663
Use 0000 Bronze Wool if you can find it- it's the least aggressive.
Slopemeno is offline  
Old August 26, 2012, 02:44 AM   #8
Scimmia
Senior Member
 
Join Date: May 19, 2011
Location: Eastern IA
Posts: 428
Green scotchbrite pads use aluminum oxide, the same thing they use on sandpaper. They are definitely more abrasive than very fine steel wool (0000).

Last edited by Scimmia; August 26, 2012 at 02:51 AM.
Scimmia is offline  
Old August 26, 2012, 06:31 AM   #9
tango1niner
Senior Member
 
Join Date: March 5, 2009
Location: NY
Posts: 316
Very nice job on the Bersa, now what the heck is frog lube and where can it be obtained?
tango1niner is offline  
Old August 26, 2012, 08:42 AM   #10
azmark
Senior Member
 
Join Date: August 26, 2007
Location: Palominas, AZ
Posts: 221
I found a quickmention of frog lube in an American Handgunner article.

http://fmgpublications.ipaperus.com/...HJA11/?page=50

Website: http://www.froglube.com
__________________
Mark Dickinson
USAF, Retired
azmark is offline  
Old August 26, 2012, 06:44 PM   #11
Dfariswheel
Senior Member
 
Join Date: May 4, 2001
Posts: 7,477
Scotchbrite pads, even the 0000 equivalent gray pads WILL strip bluing fast.

Here's how I removed rust in the shop:
Get a penetrating fluid like Kroil or CLP Breakfree. Even WD-40 will work.
Apply a good coat to the rust and let soak at least 24 hours.
The fluid will penetrate the rust and will soften and loosen it.

After soaking, apply more fluid and use a brass "toothbrush" to liberally scrub the area.
The brass will break up and remove the rust with no chance of further damaging the bluing.

If you have a hard, crusty spot, use a BRASS scraper made from brass sheet or a BRASS cartridge case with the mouth flattened and sharpened. Use the brass to scrape the crusty spot off then brush.
DO NOT use a penny or nickel. These are no longer made of copper or nickel and will damage the bluing.

After the rust is off, you'll have pitting and missing blue where the rust was. There's nothing you can do about that short of a full re-blue job.

After the rust is off, wipe the metal clean and apply a coat of CLP Breakfree. This will continue to "work" on any remaining rust and will prevent further rust.
Dfariswheel is offline  
Old August 27, 2012, 08:54 AM   #12
wyop
Senior Member
 
Join Date: July 15, 2012
Location: Wonderful, Windy Wyoming
Posts: 133
The penny is now just zinc covered with 2.5% copper since about 1982, but the nickel's composition has remained 25% Ni, 75% Cu. In WWII, the nickel coin had silver and manganese added to free up nickel metal for wartime production, but that ended in 1945.

I don't have a problem with the nickel stripping blue off guns.

Earlier this year, the melt value of a nickel coin was closing in on 8 cents, which is quite a premium over face value.
wyop is offline  
Old August 27, 2012, 10:08 AM   #13
Pahoo
Senior Member
 
Join Date: February 16, 2006
Location: IOWA
Posts: 8,783
Letting it work !!

Quote:
Apply a good coat to the rust and let soak at least 24 hours.
Very good point and one that took me too many years to discover. You can actually see the rust, flowng off the metal. Being a tad patient, can actually save on material and labor. On some applications, I let it soak for a few days. ...

Be Safe !!!
__________________
'Fundamental truths' are easy to recognize because they are verified daily through simple observation and thus, require no testing.
Pahoo is offline  
Old August 29, 2012, 11:52 PM   #14
rimshooter
Junior Member
 
Join Date: August 28, 2012
Posts: 7
Scotchbrite pads can be used to clean up scratches on stainless guns like Ruger MKII's but I wouldn't use one on a blued firearm.
rimshooter is offline  
Old August 30, 2012, 07:22 PM   #15
Dfariswheel
Senior Member
 
Join Date: May 4, 2001
Posts: 7,477
Scotchbrite is used to re-surface stainless guns and remove minor scratches and blemishes.
They work very well for that and are the preferred method for restoring stainless.

Since they'll abrade stainless and remove scratches, you can imagine what they'll do to bluing.
Dfariswheel is offline  
Old September 2, 2012, 03:16 AM   #16
natman
Senior Member
 
Join Date: June 24, 2008
Posts: 2,604
Quote:
Has anyone tried the heavy duty green 3M cleaning pads to remove rust from blued surfaces? They have to be less abrasive than steel wool or even brass.
No they don't. Some of the pads are quite abrasive. There are different grades and the grading system varies by manufacturer.

The nice thing about steel wool is that 0000 steel wool is pretty much the same everywhere. Use it with plenty of light oil and if you have the slightest understanding of what the phrase "gentle rubbing" means, you won't scratch the bluing.
natman is offline  
Old September 2, 2012, 05:52 PM   #17
bob kk
Member
 
Join Date: October 6, 2008
Location: E Tn
Posts: 56
I used scotch brite on a Kimber hunter before sending it back to kimber for a refinish. It had some rust on it and the pads removed the rust and bluing. Don't think I would use it except if it were going to be re blued.
bob kk is offline  
Old September 2, 2012, 10:15 PM   #18
Clark
Senior Member
 
Join Date: December 4, 1999
Location: WA, the ever blue state
Posts: 4,678
I have the colors of Scotch brite pads.
I have the grits of rolls of sand paper
I have the emery cloth.
I have the wet and dry paper
I have the Craytex
I have the different steel wools.
I have the different grit compounds
I have different grinding wheels.
I have the wire wheels
I have the disc pads
I have different files
I have the diamond sticks.
I have the random orbital sander
I have the belt sander
I have the vibrating sander

Some of it gets used, some does not.
And I have to keep replacing the rolls of sandpaper.

The colors of scotch brite, I buy at ENCO
http://www.use-enco.com/CGI/INPDFF?PMPAGE=257&PMCTLG=00

If I have a piece of metal in the lathe that is I want shiny, I make a high r.p.m shallow cut and slowly feed with a round tool.
Then I do the file.
Then I do the sand paper and then finer sand paper.
Cover the ways so no grit gets on the ways.
Then I go to a fine scotch brite.
Then I go to a fine steel wool.
That is a shiny as I can get it.

If I have an old gun that is rusty and I want to keep the bluing, I rub oil on it with a fine scotch brite pad every night for a long time.

If some blue comes off, I can touch it up with Oxpho blue and put oil over it. Then later wash off the oil and then put more oil on it. Don't leave blue on it long term.
__________________
The word 'forum" does not mean "not criticizing books."
"Ad hominem fallacy" is not the same as point by point criticism of books. If you bought the book, and believe it all, it may FEEL like an ad hominem attack, but you might strive to accept other points of view may exist.
Are we a nation of competing ideas, or a nation of forced conformity of thought?
Clark is offline  
Old September 2, 2012, 10:32 PM   #19
Bill DeShivs
Senior Member
 
Join Date: April 7, 2006
Posts: 10,966
If you use ANY Scotchbrite pad on a blued gun the bluing WILL come off. Replacing it with Oxphoblue is a poor substitute for leaving the original bluing on the gun.
__________________
Bill DeShivs, Master Cutler
www.billdeshivs.com
Bill DeShivs is offline  
Old September 3, 2012, 11:15 AM   #20
Clark
Senior Member
 
Join Date: December 4, 1999
Location: WA, the ever blue state
Posts: 4,678
Bill, if you rubbed the bluing off a gun with white scotch brite, by the time you were done your muscles would be so big you would need new shirts.
It could be a new look for you
__________________
The word 'forum" does not mean "not criticizing books."
"Ad hominem fallacy" is not the same as point by point criticism of books. If you bought the book, and believe it all, it may FEEL like an ad hominem attack, but you might strive to accept other points of view may exist.
Are we a nation of competing ideas, or a nation of forced conformity of thought?
Clark is offline  
Old September 4, 2012, 08:43 AM   #21
chasgrips45
Junior member
 
Join Date: January 20, 2006
Location: Franklin North Carolina
Posts: 83
Is there any residual rust, like small pit marks?
chasgrips45 is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:53 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.10829 seconds with 10 queries