The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools Search this Thread
Old February 8, 2019, 09:41 PM   #1
AzShooter
Senior Member
 
Join Date: June 20, 2006
Location: Surprise, Az.
Posts: 521
Ruger Mark IV with new trigger

I upgraded my Ruger Mark IV 22/45 Lite to meet all the specifications of the new Volquartsen Mamba. LLV-6 upper and Vortex Red Dot.

So, there it was, just sitting in the safe, the old upper. I found a vender (Wirthwein Guns) with a new lower frame and ordered it. Now I had a second 22/45 Lite but it needed a trigger job.

It wasn't bad, 3 3/4 pounds, but wasn't that good either.

I ordered the VQ accurizing kit and installed it Thursday night. Took me about 20 minutes and ended up with a 1 1/5 pound trigger. SWEET.

Today I took it to the range and fired 300 rounds of CCI Blazer and a box of CCI SV with 5 of my spare magazines and I got 100% reliability.

All I need now is a new Red Dot sight.


AzShooter is offline  
Old February 9, 2019, 01:03 PM   #2
k4swb
Senior Member
 
Join Date: July 11, 2009
Posts: 389
Does it have an OT screw? I can't see one in the trigger.
An OT screw will make it feel like you've shaved at least another 1/4 pound off of it.

Don't know the physics of this but for me an OT screw is one of the first things I try to incorporate into a trigger job. Always makes the job feel better.
__________________
My posts are things I have tried or experienced. You may or may not wish to emulate them so read them with this in mind.
Compromise means that both sides give something, but they never give, they just take.
I'm The NRA!
k4swb is offline  
Old February 9, 2019, 01:25 PM   #3
AzShooter
Senior Member
 
Join Date: June 20, 2006
Location: Surprise, Az.
Posts: 521
I added a Volquartsen Accurizing kit and their trigger has the pre and over travel screws. Works like a charm.
AzShooter is offline  
Old February 11, 2019, 07:43 AM   #4
Mobuck
Senior Member
 
Join Date: February 2, 2010
Posts: 6,590
I have two 22/45 MK3 with VQ parts. One 4" with a complete VQ accuracy upgrade and one 5.5" with assorted VQ parts accumulated from here and there. 1.5# is a bit light for my purposes but I'm pleased with 2.5+/-#.
We shoot these pistols @ 100 yards on 8" swingers making consistent hits and currently working on "two in the air" double taps(get two bullets on the way before the first hits the target). Quite impressive when it works.
Mobuck is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:58 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.04176 seconds with 10 queries