The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Revolver Forum

Reply
 
Thread Tools Search this Thread
Old February 23, 2010, 11:55 AM   #2626
woodlecj
Junior Member
 
Join Date: February 23, 2010
Location: Bethlehem, PA
Posts: 4
Serial # request

I would appreciate a serial number lookup, please. AZH2116. I just bought a 686(no dash) in stainless, 4" barrel, round butt, no security lock.

May be off topic, but I have a question on the revision numbers as well. I read somewhere that the production run of the 686 series was from 1980 to 1999. If it's a plain 686, would it be produced in the first few years of production, then the dash one is the next few years, etc.? How many revisions were there and what were the changes to each one?

Thanks in advance,
Craig
woodlecj is offline  
Old February 23, 2010, 12:10 PM   #2627
FlyFish
Senior Member
 
Join Date: January 20, 2009
Location: Overlooking the Baker River Valley
Posts: 1,730
Craig -

AZH prefix would correspond to 1988.

Your understanding of the "dash" system of design/engineering changes is basically correct. The "no dash" 686 was introduced in 1980. Revisions, their intro dates, and an [abbreviated] description of the changes:

-1 (1986) radius stud package, floating hand
-2 (1987) change hammer nose, bushing
-3 (1988) new yoke retention system
-4 (1993) change rear sight, drill and tap for scope, change extractor
-5 (1997) cylinder stop integral with frame, MIM hammer and trigger, internal changes
-6 (2001) introduce the dreaded ILS
-7 (2002) Performance Center model

The 686 is in current production, and I suspect they're selling tons of them. I have two, along with a pair of 586s, and they're great guns in every way.

With regard to the -2 change: that was in response to reports of cylinder lockup with some loads apparently caused by primer cup flowback into the firing pin bushing area. S&W issued a recall for the "no dash" and -1 models of the 586 and 686 so the firing pin and bushing could be changed to the new (-2) design. Guns that have been modified will be stamped with an "M" in the model number area. If your "no dash" doesn't have that, then it has the old design and I believe S&W will still make the change at no cost to you. If you're using it as a range gun (which is what I do with mine, a couple of which haven't been modified) then I probably wouldn't bother. If it's an SD gun, then you probably should call S&W and have it taken care of.
FlyFish is offline  
Old February 23, 2010, 12:30 PM   #2628
woodlecj
Junior Member
 
Join Date: February 23, 2010
Location: Bethlehem, PA
Posts: 4
Thanks for the quick and concise response Mr. FlyFish! Let me pick your brain some more.

I checked in the crane area and it does have an "M" and a "2" there, so, I guess it makes it essentially a 686-2. Would the mods then have included the -1 parts?

Also if it was made in 1988 and the -1 was cut in to production in 1986, why would S&W still make no dash versions for two years? Only asking if you know, I'm not asking if you understand S&W manufacturing wierdness.

Thanks again,
Craig
woodlecj is offline  
Old February 23, 2010, 01:52 PM   #2629
FlyFish
Senior Member
 
Join Date: January 20, 2009
Location: Overlooking the Baker River Valley
Posts: 1,730
Is it actually stamped "686-2", i.e., on a single line and looking like it was stamped at the same time? That's the way it should be if it's actually a -2, and based on the SN/production date that's what it should be rather than a "no dash". The whole point of the -2 was to fix the earlier problems with the -1 and earlier guns, so I can't imagine they'd label a gun as the -2 but use the old -1 parts.

The "M" is a bit curious because the -2 definitely did not need to be modified. S&W is famous for extraneous stampings in the frame cutout, some of which are "assembly numbers" used to keep track of fitted parts during the manufacturing process, but I wouldn't think they'd use an "M" for that purpose. Given the apparent confusion, and the seeming importance of the recall issue for the early 586/686 guns, I think a call to S&W customer support would answer a lot of questions for you as they should have records indicating what, if anything, was done to that particular gun.
FlyFish is offline  
Old February 23, 2010, 04:52 PM   #2630
Nomadicone
Senior Member
 
Join Date: January 31, 2008
Location: Arizona
Posts: 214
First let me say I appreciate someone going to the trouble of looking these up and giving feedback. Very nice service from all participating. I have three:

Mod 17-4 SN 25K53XX

Mod 57 SN N8851XX there is no number after the Mod 57

Mod 66-3 SNBFH37XX
Nomadicone is offline  
Old February 23, 2010, 05:09 PM   #2631
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
Mod 17-4 SN 25K53XX

Mod 57 SN N8851XX there is no number after the Mod 57

Mod 66-3 SNBFH37XX
Mod 17-4 SN 25K53XX = 1978
Mod 57 SN N8851XX there is no number after the Mod 57 = N800000 range ran from 1980 to 83 so yours would likely be closer to 1983.
Mod 66-3 SN BFH37XX = late 1989/ early 90.

Jim
laytonj1 is offline  
Old February 23, 2010, 05:25 PM   #2632
Nomadicone
Senior Member
 
Join Date: January 31, 2008
Location: Arizona
Posts: 214
Thanks much Jim. Very helpful to know.
Nomadicone is offline  
Old February 24, 2010, 12:17 AM   #2633
357
Member
 
Join Date: February 24, 2010
Location: Virginia
Posts: 19
Mod 27

Hello! Hoping to find out when this gun was made.

Mod 27 SN S1992XX (Blue 4" barrel)

Thanks in advance!
357 is offline  
Old February 24, 2010, 12:27 AM   #2634
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
Mod 27 SN S1992XX
Serial numbers ran from S194500 in 1959 to S206999 in 1960.

Jim
laytonj1 is offline  
Old February 24, 2010, 09:45 AM   #2635
Delta 556
Junior Member
 
Join Date: February 24, 2010
Posts: 2
Just got a basket case S&W. Its gonna need a yoke and possible a sideplate. Can anybody give me the date of manufacture and any other info? Ita a 4" K-38. SN#K 306XXX. Any info would be greatly appreciated.
Delta 556 is offline  
Old February 24, 2010, 10:13 AM   #2636
spacecoast
Senior Member
 
Join Date: October 14, 2009
Location: Sunshine and Keystone States
Posts: 4,461
Need an approx. date of birth for a Model 60 SN 330xxx.

Thanks in advance...
spacecoast is offline  
Old February 24, 2010, 10:51 AM   #2637
FlyFish
Senior Member
 
Join Date: January 20, 2009
Location: Overlooking the Baker River Valley
Posts: 1,730
Quote:
Can anybody give me the date of manufacture and any other info? Ita a 4" K-38. SN#K 306XXX.
1957. If it doesn't have a model number you must have one of the last that was made without it (model numbering started in 1957). As you probably know, the 4" barrel - and it should have the ramped rather than Patridge front sight - makes it a K-38 Combat (vs. Target) Masterpiece, a pre-Model 15.

Quote:
Need an approx. date of birth for a Model 60 SN 330xxx.
According to SCSW, Model 60 SNs started around 401754. Is there possibly an "R" in front of the numerals?
FlyFish is offline  
Old February 24, 2010, 11:06 AM   #2638
Delta 556
Junior Member
 
Join Date: February 24, 2010
Posts: 2
FlyFish
Thanks for the info. It also has an H stamped on the frame under the yoke and the chambers are numbered.Does this make a difference? Thanks again.
Delta 556 is offline  
Old February 24, 2010, 11:17 AM   #2639
FlyFish
Senior Member
 
Join Date: January 20, 2009
Location: Overlooking the Baker River Valley
Posts: 1,730
Delta 556 -

I don't think either is unusual or of any particular significance in older S&W revolvers.
FlyFish is offline  
Old February 24, 2010, 04:33 PM   #2640
357
Member
 
Join Date: February 24, 2010
Location: Virginia
Posts: 19
Thanks! (Mod 27 Question)

Thanks laytonj1 for the info and the really fast reply!
357 is offline  
Old February 25, 2010, 11:12 AM   #2641
woodlecj
Junior Member
 
Join Date: February 23, 2010
Location: Bethlehem, PA
Posts: 4
Picture of frame area

<<<Is it actually stamped "686-2", i.e., on a single line and looking like it was stamped at the same time? That's the way it should be if it's actually a -2, and based on the SN/production date that's what it should be rather than a "no dash". The whole point of the -2 was to fix the earlier problems with the -1 and earlier guns, so I can't imagine they'd label a gun as the -2 but use the old -1 parts.

The "M" is a bit curious because the -2 definitely did not need to be modified. S&W is famous for extraneous stampings in the frame cutout, some of which are "assembly numbers" used to keep track of fitted parts during the manufacturing process, but I wouldn't think they'd use an "M" for that purpose. Given the apparent confusion, and the seeming importance of the recall issue for the early 586/686 guns, I think a call to S&W customer support would answer a lot of questions for you as they should have records indicating what, if anything, was done to that particular gun.>>>

FlyFish,

Here's a closeup of the area. Looks to me like it is a 686 with no room to stamp a -2 on the end so they marked it atop of the 686. Looks like an "M" follows the 2. I welcome your thoughts.

Thanks,
Craig

Last edited by Glenn E. Meyer; November 30, 2013 at 11:47 AM.
woodlecj is offline  
Old February 25, 2010, 11:20 AM   #2642
spacecoast
Senior Member
 
Join Date: October 14, 2009
Location: Sunshine and Keystone States
Posts: 4,461
Need an approx. date of birth for a Model 10-5 SN D730xxx.

Thanks in advance...
spacecoast is offline  
Old February 25, 2010, 11:44 AM   #2643
FlyFish
Senior Member
 
Join Date: January 20, 2009
Location: Overlooking the Baker River Valley
Posts: 1,730
Craig -

This is very curious. As I alluded to earlier, I have never seen the "dash" variation indicated other than on the same line, in the same font, with the correct spacing, and appearing as though it had all been stamped at the same time. If there's insufficient room in the frame cutout, the "Mod" part is usually on a different "line" immediately above the numerals. None of that is the case here, and I don't think that "2" is intended to indicate that the gun is a -2 model - at least I've never seen the dash variation marked that way. The "M" on the other hand appears identical to the M stamped on my guns to indicate that they had the firing pin/bushing modification made. The confusion comes because, according to SCSW, the SN should indicate 1988 production, at which time it should have been a -2, which didn't need the modification.

SNs have been used out of their correct order at times, and that may be the case here, so you may have a "no dash" with a SN out of normal range that was subsequently modified in response to the recall. Jim (laytonj1), if you're reading this perhaps you could venture an opinion - you know tons more about this stuff than I do.

Given the confusion, and the fact that this model was the subject of a very rare recall, I'm sure that S&W Customer Service would be willing and able to tell you exactly what the story is if you give them the SN. If you do call them and find out, please post back here and let us know what the answer is.
FlyFish is offline  
Old February 25, 2010, 11:48 AM   #2644
FlyFish
Senior Member
 
Join Date: January 20, 2009
Location: Overlooking the Baker River Valley
Posts: 1,730
Quote:
Need an approx. date of birth for a Model 10-5 SN D730xxx.
spacecoast -

1974 to 1975. The SN range for those years was from D659002 to D750000, so probably 1975.
FlyFish is offline  
Old February 25, 2010, 12:51 PM   #2645
spacecoast
Senior Member
 
Join Date: October 14, 2009
Location: Sunshine and Keystone States
Posts: 4,461
Flyfish -

Thanks, much obliged. '75 was a great year, especially for Reds fans.
spacecoast is offline  
Old February 25, 2010, 01:21 PM   #2646
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
woodlecj,

The CS-1 stamped on the frame identifies it as product code 104229. It was part of a special order made for the U.S. Customs Service in 1988. Besides the CS-1 stamp, they had a 4" barrel, pinned black front sight, round butt and dull grey bead blast finish. There was also a 3" version, product code 104228.
The "2M" stamp means the gun had the bushing recall done before it was shipped.
These guns also sale for a premium.

Jim

Last edited by laytonj1; February 25, 2010 at 01:45 PM. Reason: more info
laytonj1 is offline  
Old February 25, 2010, 01:44 PM   #2647
woodlecj
Junior Member
 
Join Date: February 23, 2010
Location: Bethlehem, PA
Posts: 4
Jim and Flyfish,
Thanks very much!
woodlecj is offline  
Old February 26, 2010, 08:41 PM   #2648
drddrd
Junior Member
 
Join Date: February 20, 2010
Location: Wisconsin
Posts: 4
I would like to be able to date a model 469 9mm. Serial number TBB7785
drddrd is offline  
Old February 26, 2010, 09:49 PM   #2649
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
Serial number TBB7785
1987.

Jim
laytonj1 is offline  
Old February 27, 2010, 09:55 AM   #2650
drddrd
Junior Member
 
Join Date: February 20, 2010
Location: Wisconsin
Posts: 4
Thanks Jim
drddrd is offline  
Reply

Tags
s&w 686

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:53 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2024 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.39356 seconds with 9 queries