The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Revolver Forum

Reply
 
Thread Tools Search this Thread
Old April 22, 2015, 10:42 PM   #6901
range_rider13
Member
 
Join Date: July 10, 2007
Location: Tex-Mex Border
Posts: 38
DOB for S&W Model 17-6

Could you please tell me the date of manufacture for a Blue Model 17-6 .22 LR cal., 6 inch full lug barrel, 6 shot cylinder, target trigger, target hammer, target checkered grips, serial # BFM6XXX?
Thank you!
__________________
"If you climb into the saddle be ready for the ride!"
range_rider13 is offline  
Old April 24, 2015, 05:52 PM   #6902
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
I have a S&W M&P 38. Round butt with hard rubber grips. 5" barrel and fixed sights
Serial Number is 5799XX
Late 1920's.

Quote:
serial # BFM6XXX?
1990.

Jim
laytonj1 is offline  
Old April 24, 2015, 06:49 PM   #6903
Sevens
Senior Member
 
Join Date: July 28, 2007
Location: Ohio
Posts: 11,770
I've mentioned this on occasion in scattered discussions regarding the Model 17 and I'll mention it here for this Model 17 posted above--

I also have a 17-6, mine has a BBJ serial prefix (1989) and wish to point out the little bit of S&W lunacy (IMO of course) in that S&W elected to go from the traditional target barrel to the full-lug barrel without changing dash numbers.

It isn't clear to me how many of the dash-6 exist or what the balance of standard barrel versus full-lug barrel may be, but I continue to find it ludicrous that S&W didn't feel it was prudent or necessary to transition to the next dash number for what amounts to a RADICAL change and not a tiny little one.
__________________
Attention Brass rats and other reloaders: I really need .327 Federal Magnum brass, no lot size too small. Tell me what caliber you need and I'll see what I have to swap. PM me and we'll discuss.
Sevens is offline  
Old April 26, 2015, 09:47 AM   #6904
CraZ4GunZ
Junior Member
 
Join Date: December 29, 2008
Location: Maryland
Posts: 3
Hello,
I just received this S&W revolver 18-3 from an uncle. The ser no. is 8K-9xxxx.
Just found my answer after a little digging.
Thanks anyway.

Last edited by CraZ4GunZ; April 28, 2015 at 07:01 AM.
CraZ4GunZ is offline  
Old April 27, 2015, 06:31 PM   #6905
Darkroad1959
Junior Member
 
Join Date: April 26, 2015
Posts: 1
DOB 38 Special Revolver

Hello All
I recently acquired a old 38 special with a lanyard loop on the butt. It has serial number of 784xxx. Could someone help me find out when she was born?
Thanks for the help


Phil
Darkroad1959 is offline  
Old April 29, 2015, 10:55 PM   #6906
range_rider13
Member
 
Join Date: July 10, 2007
Location: Tex-Mex Border
Posts: 38
DOB S&W Model 17-6

Could you please tell me the date of manufacture for a Blue Model 17-6 .22 LR cal., 6 inch full lug barrel, 6 shot cylinder, target trigger, target hammer, target checkered grips, serial # BFM6XXX?
Thank you!

Quote:
serial # BFM6XXX?
1990.

Jim


Thank you very much Jim!
RR13
__________________
"If you climb into the saddle be ready for the ride!"
range_rider13 is offline  
Old April 30, 2015, 02:10 PM   #6907
potpieguy
Junior Member
 
Join Date: April 30, 2015
Posts: 6
How to date a couple S&Ws

Is this where and how I'd ask for the mfg. dates of two revolvers? Just joined, so I'm unsure how things work
potpieguy is offline  
Old April 30, 2015, 04:08 PM   #6908
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
It has serial number of 784xxx
With no "SV" prefix, around 1940. With "SV" prefix, around 1944.

Quote:
Is this where and how I'd ask for the mfg. dates of two revolvers? Just joined, so I'm unsure how things work
I see your question has already been answered.

Jim
laytonj1 is offline  
Old April 30, 2015, 05:09 PM   #6909
potpieguy
Junior Member
 
Join Date: April 30, 2015
Posts: 6
2 revolvers dates

Laytonj1...Jim...
I was given some interesting info on these two old fellas but no one supplied the dates of manufacture. Reading thru these threads it seems most people can find out just when (or appx.) their revolver was made. Is there any way I can learn when my two guns were made, or do they fall into some black hole that can't be traced? I've had the .455 about 40 years now, I'd really like to know just how old they are.
potpieguy is offline  
Old May 1, 2015, 08:35 AM   #6910
Mojave
Member
 
Join Date: June 11, 2011
Posts: 68
I recently acquired a lovely 629-4, serial BSW48xx. Any guesses as to when it was made?

Thanks!
Mojave is offline  
Old May 1, 2015, 10:38 AM   #6911
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
Laytonj1...Jim...
I was given some interesting info on these two old fellas but no one supplied the dates of manufacture.
From the Standard Catalog of Smith & Wesson:
Serial numbers 1 thru ~ 163600 ran from Sep 1917 to Jan 1919.
A 1938 shipment of Brazilian guns were serial numbered in the 181983 to 207043 range. Another shipment in 1946 ran in the 207196 to 207989 range.

Quote:
629-4, serial BSW48xx
1994/95.
In my opinion (and many others), the -4 was the best of the 629's. Had all the latest strength upgrades and was pre MIM and IL.

Jim
laytonj1 is offline  
Old May 1, 2015, 02:14 PM   #6912
Mojave
Member
 
Join Date: June 11, 2011
Posts: 68
Quote:
1994/95.
In my opinion (and many others), the -4 was the best of the 629's. Had all the latest strength upgrades and was pre MIM and IL.

Jim
Thanks Jim!! I certainly appreciate you taking the time to answer these. I knew it was pre-lock, but I didn't know the -4 was particularly desirable. Good to know I didn't screw that up
Mojave is offline  
Old May 6, 2015, 10:12 PM   #6913
potpieguy
Junior Member
 
Join Date: April 30, 2015
Posts: 6
S&W NewDeparture

Can you give an appx. date for a Lemonsqueezer/NewDeparture .38 S&W. It has 3 1/4" bbl. A little checkered button on the top strap, push it down and the gun breaks open. Last pat. date Jun 3 .90. Now the serial #s are odd, the bottom of butt has 80043 and the cylinder says 80045. I needed a magnifying glass to notice the difference. Could that be a factory error, it seems unlikely a replacement cyl. would be that close. The nickel finish has a lot of wear and the grips were a mess,but; it functions perfectly, indexes perfectly. Bore and chambers nice. Is this safe with modern available ammo?
potpieguy is offline  
Old May 8, 2015, 09:13 PM   #6914
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
Can you give an appx. date for a Lemonsqueezer/NewDeparture .38 S&W.
Safety Hammerless 3rd Model. Serial numbers ran from 42484 in 1890 to 116002 in 1898. Without seeing it myself, I would guess the serial numbers are the same. A 3 and 5 can look an awful lot alike when stamped into metal.

Jim
laytonj1 is offline  
Old May 12, 2015, 11:02 AM   #6915
Tommy Vercetti
Senior Member
 
Join Date: June 26, 2004
Location: Fairhope, Alabama
Posts: 1,119
how about a model 65-2? serial number 7060xxx?
Tommy Vercetti is offline  
Old May 12, 2015, 04:37 PM   #6916
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
model 65-2? serial number 7060xxx?
That's not the serial number. Take it from the underside of the grip frame. You may have to remove the grips to see it. 65-2's were made from 1977 to 82 so the serial number will likely have a "D" as the second or 3rd digit.

Jim
laytonj1 is offline  
Old May 15, 2015, 10:45 AM   #6917
Whisky
Junior Member
 
Join Date: May 15, 2015
Posts: 2
..helping my Wife's friend and our neighbor..

.
the neighbor has a S&W .38spec that her Father left to her - shes asked my to try and find "what the pistol is"

the only thing I have is the serial number (710XXX), the fact that it's a S&W .38spec and that it's Stainless

any help as to what model S&W it is and perhaps year would be appreciated

thank you
Whisky is offline  
Old May 15, 2015, 03:17 PM   #6918
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
the only thing I have is the serial number (710XXX), the fact that it's a S&W .38spec and that it's Stainless
Not much to go on but assuming you took the serial number from the underside of the grip frame (there are assembly numbers in other locations), that there were no letter prefixes a few spaces before the serial number, that it is a five shot, and is in fact stainless and not nickel, then it could be a model 60 made around 1968.

Jim
laytonj1 is offline  
Old May 15, 2015, 04:00 PM   #6919
Whisky
Junior Member
 
Join Date: May 15, 2015
Posts: 2
.
did take the number from the bottom of the grip - no spaces, no letters

guessing it's stainless and it's a 6 shooter

would a pic help ? easy enough to do that............thanks
Whisky is offline  
Old May 15, 2015, 04:14 PM   #6920
kentuckycowboy2
Junior Member
 
Join Date: June 11, 2009
Posts: 2
Hello everyone, I have a old S&W model 10-5 given to me by my grandmother after my grandfather passed on. I'm needing to order a few parts for it & not sure if the manufacture date will help or not, if someone could help me with it I would be most appreciative.

It seems to be old and the serial number is a 5 digit ( D4XXX ) I see nothing else after that & it is a square butt frame. I need to replace the hand that ratchets the cylinder and am a bit confused as to whether I need a two or three pin hand for this one, maybe someone can enlighten us.

Thanks John
kentuckycowboy2 is offline  
Old May 15, 2015, 04:52 PM   #6921
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
serial number is a 5 digit ( D4XXX )
1968.
Serial numbers ran from D1 to D90000 that year.
As to the rest of your question, the best place to get an answer is the S&W forum.
http://smith-wessonforum.com/

Jim
laytonj1 is offline  
Old May 19, 2015, 09:04 PM   #6922
builttospill
Junior Member
 
Join Date: May 17, 2015
Posts: 2
Hi everyone, I have an old Model 10-5 and after some searching I'm having a hard time confirming the exact year due to the first two characters not showing up in a catalog. I'm guessing 1978 but thought someone here might know more than me. The serial number is 3D2XXX.
builttospill is offline  
Old May 20, 2015, 04:48 PM   #6923
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
The serial number is 3D2XXX.
Not sure why the 3D's were left out. The book also states that 10-5's ran from 1962 to 1977. So... 77/78.

Jim
laytonj1 is offline  
Old May 20, 2015, 11:22 PM   #6924
builttospill
Junior Member
 
Join Date: May 17, 2015
Posts: 2
Thanks Jim.
builttospill is offline  
Old May 31, 2015, 01:02 PM   #6925
Viper99
Senior Member
 
Join Date: October 19, 2010
Location: CT
Posts: 846
Can anyone give me information on a S&W model 396 s/n CED196X (X in place of last number)

Regards
Viper99 is offline  
Reply

Tags
s&w 686

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:59 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2024 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.61834 seconds with 9 queries