The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools Search this Thread
Old April 5, 2013, 06:06 PM   #1
p5200
Senior Member
 
Join Date: April 1, 2008
Posts: 241
Trouble fitting Weaver#61 bases on a Tikka t3 Deluxe in 270 win.

The factory aluminum clamp on rings are soft and allowed the scope to slide through them and also, the aluminum allen head screws that tighten to the base stripped out the heads. I found a set of Weaver #61 flat bottom bases that are suppose to work but, the screws feel like they might be too big in diameter when I tested one without the base. The holes seem to line up on the receiver just fine though. I read on another forum where a person ordered a set of the Talley rings and found the same problem they sent him two more sets of screws to try but, same thing. He said finally, he put quite a bit more force on the screws and they went in just fine? Are the factory filler screws plastic maybe a little undersize and I too, need to apply more force? I just don't want to bugger up the threads in the receiver where I can't use it any more. The factory plugs measure 3.0mm. but I can't hardly see or feel any threads on them. the Weaver screws measure 3.4mm. in diameter and the threads can be seen and felt easily. I'd sure appreciate some info if possible, Thanks!
p5200 is offline  
Old April 5, 2013, 08:19 PM   #2
p5200
Senior Member
 
Join Date: April 1, 2008
Posts: 241
Well, I found out anything before 2004 uses metric and anything after, uses 6-48 thread the only thing is I don't know how to tell how old mine is by the serial number. I bought mine new but, it was (old stock) and was sitting on the rack a long time. I got it home and removed the bolt to give it a good cleaning and noticed the plastic bolt shroud was cracked. I contacted Beretta USA and when I gave the serial # the man asked if it was a new gun because it was manufactured 6 years ago. I explained it was new just, old stock and I had the proof of purchase receit. He went ahead and sent a new shroud 6 years ago would mean 2007 so, can I assume the receiver would be tapped for the standard Weaver 6-48 thread? I wish I knew another way to verify the date of manufacture. I've noticed while searching the net I ran across at least, three people who had the same concerns about the screws but they did, get them to go in so maybe I'll just put a dab of lok-tite and give it a go. Thanks!
p5200 is offline  
Old April 6, 2013, 12:27 AM   #3
hoghunting
Senior Member
 
Join Date: March 27, 2006
Posts: 1,559
Before taking the risk of stripping the hole, go to a gun shop and buy a 6-48 screw to try for size - the shop may even give you one. If you need the 6-48, then contact Weaver and they'll send them to you.
hoghunting is offline  
Old April 7, 2013, 02:21 PM   #4
p5200
Senior Member
 
Join Date: April 1, 2008
Posts: 241
Well, after all that worry I set a base on the receiver put a dab of blue lock-tite on the tip of the screw and it went in just perfect so, I installed the scope.
p5200 is offline  
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:20 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.04875 seconds with 10 queries