|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
November 19, 2008, 02:04 AM | #1 |
Senior Member
Join Date: October 30, 2008
Location: Wild, Wonderful West Virginia
Posts: 315
|
Remington action adjustment
I have a remington 710 in 30-06 and the action leaves a little to be desired. I think that the bolt is coated with this graphite substance for oiless lubrication. The idea didn't produce the best results. Another problem is that it seems hard to lock the bolt down and into the ready position. Does anyone have any suggestions on ways to fix this problem? I want to be able to fix this myself. I'm sure some might want to tell me to get a different gun, but it shoots accurate as I need for the area I hunt.
__________________
The strongest reason for the people to retain the right to bear arms is, as a last resort, to protect themselves against tyranny in government. -Thomas Jefferson |
November 19, 2008, 04:22 AM | #2 |
Senior Member
Join Date: February 4, 2006
Posts: 206
|
Hillbilly: I notice the same problem on a customer's 770. Most of the drag on his was caused by the bolt shroud and cocking piece. You probably could lap the threads and contact surfaces, but it might be the best to leave it be.
Some might tell you to get another rifle, but the 710/770 are not all that bad. There are a few things I don't like about them, but they're serviceble and inexpensive. The owner of the 770 killed a 10 point with his, and that buck was as dead as any shot with a $1,000+ rifle. |
November 19, 2008, 09:22 AM | #3 |
Junior member
Join Date: July 26, 2007
Posts: 3,668
|
Buy a mediocre hacksaw....! (You won't need a good one.) Local postal clerk, who knows that I do a little armoring, asked me the same question about his 710. I advised him to change the "1" to another "0".
|
November 19, 2008, 12:37 PM | #4 |
Senior Member
Join Date: October 30, 2008
Location: Wild, Wonderful West Virginia
Posts: 315
|
Polishing Compound
I saw on another post about using polishing compound and polishing the bolt. Do you think that this might help? Cause if it could take off that graphite coating and get down to the metal then in theory this should stop the binding problem.
__________________
The strongest reason for the people to retain the right to bear arms is, as a last resort, to protect themselves against tyranny in government. -Thomas Jefferson |
November 19, 2008, 01:13 PM | #5 |
Senior Member
Join Date: February 13, 2006
Location: Washington state
Posts: 15,248
|
It's not graphite coating on the bolt, it's Nylon coating. Yes, you could lap it down, but that might cause other problems.
__________________
Never try to educate someone who resists knowledge at all costs. But what do I know? Summit Arms Services |
November 19, 2008, 01:20 PM | #6 |
Senior Member
Join Date: October 30, 2008
Location: Wild, Wonderful West Virginia
Posts: 315
|
What kind of problems?
Is there any way I could test it before I do the whole thing to know if there are going to be problems? What are these problems that you are considering? Would it cause problems with sealing the barrel?
__________________
The strongest reason for the people to retain the right to bear arms is, as a last resort, to protect themselves against tyranny in government. -Thomas Jefferson |
November 19, 2008, 01:27 PM | #7 |
Senior Member
Join Date: February 13, 2006
Location: Washington state
Posts: 15,248
|
The 710 action has a Nylon sleeve inside it to reduce friction, same reason the bolt is Nylon coated. Some solvents can make the surface of the sleeve sticky. Nylon to Nylon contact slides well, Nylon to metal does not always slide well.
I would recommend using some BreakFree on the bolt rather than mess with the rifle. Once you start modifying things, it's all downhill. Or sell the rifle and buy something else if you don't like it.
__________________
Never try to educate someone who resists knowledge at all costs. But what do I know? Summit Arms Services |
November 20, 2008, 02:19 PM | #8 |
Senior Member
Join Date: October 30, 2008
Location: Wild, Wonderful West Virginia
Posts: 315
|
Scorch,
Are you recommending using the bore cleaner or the lube? B/c I have recently read that some of the oils will cause the coating on the bold to swell.
__________________
The strongest reason for the people to retain the right to bear arms is, as a last resort, to protect themselves against tyranny in government. -Thomas Jefferson |
November 20, 2008, 04:42 PM | #9 | |
Senior Member
Join Date: February 13, 2006
Location: Washington state
Posts: 15,248
|
Quote:
__________________
Never try to educate someone who resists knowledge at all costs. But what do I know? Summit Arms Services |
|
|
|