Beretta 92FS Trigger work?

Jamie Young · August 22, 2001, 08:37 PM

I know this topic has been brought up here but I can't find anything with the Search Function

. Are there any potential drawbacks to replacing the spring on my beretta 92fs to reduce trigger creep/pull?

Is it going to just change the pull on the first round?

Where can I get the spring?

teufelmann55 · August 22, 2001, 09:06 PM

Brownells' sells a gadget made to help the trigger pull on the Beretta series of pistols it seems to work ok-but it is for only single action mode of fire, the double action mode revolves around the trigger bar, mainspring weight, firing pin block and a few other things. I have seen Beretta pistols with very nice and lighter double action pulls- but the data on doing it is proprietary.

railroader · August 22, 2001, 10:45 PM

http://www.gunsprings.com/SemiAuto/B...html#Beretta92 Here's your springs. Mark

George Stringer · August 23, 2001, 08:39 AM

Soda Pop, changing the spring should reduce the weight of pull a little but it won't help with creep. The only way to get rid of creep is by having a trigger job done on the pistol. A lighter spring will lighten both SA and DA pulls. George

Jamie Young · February 11, 2002, 06:11 PM

I know this is an Old post, but I'm about to finally make a move on getting it done.

What kind of "Trigger Work" needs to be done to get rid of the Single action "Creep"?

I don't care about the pull just getting rid of the SA Creep.

Sam Norton · February 11, 2002, 11:07 PM

http://www.langdontactical.com/main.htm

Every thing I have read says this is the only way to go. I just wish they made one for a CZ.

Best
Sam N.

August 22, 2001, 08:37 PM	#1
Jamie Young Senior Member Join Date: April 7, 2000 Location: SE/PA Posts: 4,834	Beretta 92FS Trigger work? I know this topic has been brought up here but I can't find anything with the Search Function. Are there any potential drawbacks to replacing the spring on my beretta 92fs to reduce trigger creep/pull? Is it going to just change the pull on the first round? Where can I get the spring? __________________ Find out about Gun Shows and Training activities. www.TheRallyPoint.org Get your gun club involved!!

February 11, 2002, 06:11 PM	#5
Jamie Young Senior Member Join Date: April 7, 2000 Location: SE/PA Posts: 4,834	I know this is an Old post, but I'm about to finally make a move on getting it done. What kind of "Trigger Work" needs to be done to get rid of the Single action "Creep"? I don't care about the pull just getting rid of the SA Creep. __________________ Find out about Gun Shows and Training activities. www.TheRallyPoint.org Get your gun club involved!!

August 22, 2001, 09:06 PM	#2
teufelmann55 Member Join Date: May 12, 2001 Posts: 92	Brownells' sells a gadget made to help the trigger pull on the Beretta series of pistols it seems to work ok-but it is for only single action mode of fire, the double action mode revolves around the trigger bar, mainspring weight, firing pin block and a few other things. I have seen Beretta pistols with very nice and lighter double action pulls- but the data on doing it is proprietary.

August 22, 2001, 10:45 PM	#3
railroader Senior Member Join Date: February 8, 2000 Location: Tucson Arizona Posts: 1,756	http://www.gunsprings.com/SemiAuto/B...html#Beretta92 Here's your springs. Mark

August 23, 2001, 08:39 AM	#4
George Stringer Staff Alumnus Join Date: October 12, 1998 Location: Earlington KY Posts: 2,299	Soda Pop, changing the spring should reduce the weight of pull a little but it won't help with creep. The only way to get rid of creep is by having a trigger job done on the pistol. A lighter spring will lighten both SA and DA pulls. George

February 11, 2002, 11:07 PM	#6
Sam Norton Member Join Date: September 3, 1999 Location: Sarasota FL Posts: 93	http://www.langdontactical.com/main.htm Every thing I have read says this is the only way to go. I just wish they made one for a CZ. Best Sam N.