The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools Search this Thread
Old July 23, 2018, 08:20 PM   #1
ReloadKy
Senior Member
 
Join Date: February 23, 2018
Posts: 191
243 reloading help

So my wife has decided that she is going to get a little more serious about deer hunting this year so I am making it my goal to get her a deer. She has shot my 270 before and shot my Ruger American 243 today. She likes the 243 better so this is going to be her deer rifle. My question is what bullet do I go with to reload her some deer loads. My rifle has a 1:9 twist. I have been looking at the Sierra GameKing in 100 gr and the Nosler ballistic tip in 95 gr. I am also open to other bullet suggestions. I have a little time to try and figure it out but I am looking for suggestions from some of you that have reloaded 243 for deer and used the reloads successfully in the field. Help me out please! I am grateful for any insights!
ReloadKy is offline  
Old July 23, 2018, 09:35 PM   #2
Panfisher
Senior Member
 
Join Date: July 30, 2010
Location: Missouri
Posts: 1,337
I reload for my wife's Ruger .243. I load 100 grain Hornady Inter lock over 34. Grains of IMR 4895. Very mild load that she has zero issues shooting, and will absolutely pound deer and punch through both shoulders. The load has never been bench rest accurate but she keeps her shots at 100 yards or less and is deadly.
Panfisher is offline  
Old July 23, 2018, 09:57 PM   #3
Irish Lad
Member
 
Join Date: January 24, 2016
Posts: 69
I load 243 for my grandson. 100 gr. Nosler Partitions have worked extremely well using 34.5 gr of 4064.
Irish Lad is offline  
Old July 24, 2018, 02:21 AM   #4
Roadkill2228
Senior Member
 
Join Date: March 8, 2014
Location: Nipawin, Saskatchewan
Posts: 311
It’s a super cheap bullet but the Speer 100 grain boat tail soft point (not to be confused with the hotcor, another good projectile) is the most accurate bullet I’ve tried in my old savage 99 .243. It’s a soft bullet. Extremely good for classic double lung shot (much more humane than tougher premium bullets) but probably not the best if you prefer shoulder breaking anchoring shots. For that application the exact opposite kind of bullet might be what you’re after. Barnes 85 grain tsx will have no trouble achieving full penetration from just about any conceivable angle. Haven’t been as accurate in my rifle though, and as velocity falls away this bore diameter becomes quite a slow killer when using such ultra tough bullets as wounding is narrow. So my vote is for the Speer btsp or Sierra game king (or the 103 eld x, 95 btip) pass on less than ideal shots, kill it fast with a no nonsense boiler room shot at conventional hunting distance (inside 300 yards). Many powders work well in .243. I prefer a right full case of slow powder. Superformance, 4350, 4831, 7828, 7828 ssc, rl19, rl22 have all done well. It’s been a pleasure to load for. I want to try the new enduron powders out in it. My only frustration is the short case life and lots of case trimming. That’s mostly because I’m shooting a lever gun with a rear locking action, so the cases stretch a lot more with each fire and resize cycle than in a bolt gun, but even with that said, I don’t think the .243 is an especially good case design when it comes to long reloading life. That gentle long shoulder and stubby little neck are annoying to me. Like you, I much prefer my .270 both for hunting and for hand loading.
Roadkill2228 is offline  
Old July 24, 2018, 04:09 AM   #5
std7mag
Senior Member
 
Join Date: June 23, 2013
Location: Central Taxylvania..
Posts: 3,609
I'm not sure you could go much wrong with any of the above mentioned bullets.
With my wife's 243 she liked the 100gr GameKings SPBT over a charge of RL26.
__________________
When our own government declares itself as "tyrannical", where does that leave us??!!

"Januarary 6th insurrection".
Funny, I didn't see a single piece of rope...
std7mag is offline  
Old July 24, 2018, 02:29 PM   #6
ligonierbill
Senior Member
 
Join Date: May 20, 2007
Posts: 2,427
Yep, lots of good choices. Not that mine are better, but:

100 SGK/IMR-4064/2,950. Shot 1 1/8" but that's including one flier. Four were in one hole.

80 Barnes TTSX/Re-19 or Re-17/3,060. Shoots 1" with either powder.

These are out of a Ruger American. Had it out this morning. Ugly gun, pretty targets.
ligonierbill is offline  
Old July 24, 2018, 03:40 PM   #7
ReloadKy
Senior Member
 
Join Date: February 23, 2018
Posts: 191
Thanks for all of the suggestions!!
ReloadKy is offline  
Old July 25, 2018, 12:12 PM   #8
T. O'Heir
Senior Member
 
Join Date: February 13, 2002
Location: Canada
Posts: 12,453
Been using a Speer 105 grain SP with IMR4350 for eons. However, Bambi won't know or care what bullet killed him. Any 85 plus grain bullet will do.
Just remember that she has to sight the thing in. You cannot do it for her.
__________________
Spelling and grammar count!
T. O'Heir is offline  
Old July 25, 2018, 02:51 PM   #9
mkl
Senior Member
 
Join Date: April 25, 2008
Location: DFW area, Texas
Posts: 494
Nosler 100 grain partitions have worked well for me in my .243 for over 30 years and a couple of dozen deer.

I go for the shoulder shot so as to drop the deer immediately and not have to chase it wounded. I have never lost a deer with that bullet and that shot. Break that front shoulder (or both depending on the angle) and the deer won't move more that 25 feet or so.

The 100 grain Nosler minimizes meat loss with the shoulder shot -- you will lose three pounds or so and that is all. For me that is a good trade off as opposed to chasing a wounded deer and perhaps losing it.

Penetration is great so that if you can't get a perfect shoulder shot, the bullet will generally penetrate the body regardless of the angle and drop the deer within 50 yards or so.

My .243 gets the best accuracy with slow powders so I use IMR 4350 or H4831 behind all of my bullets.
mkl is offline  
Old July 26, 2018, 01:44 AM   #10
briandg
Senior Member
 
Join Date: May 4, 2010
Posts: 5,468
Any cup and core bullet will work for you, speer, sierra, even remington or hornady bullet will do well. I would prefer to use a partition or bonded core simply because they are a lot more reliable. I don't really think that a polymer tip is needed, bullets these days are well designed and don't need the tip to start the mushroom.

I have found that large charges of slow powder are accurate. Very accurate. Some use 4831, I've tried it and didn't like it. 4350 IMR gets about 3,000 fps and amazing accuracy. I mostly used the sierra 100 BT game king as well, with a near max load of 4350, and have been consistent with MOA groups.
__________________
None.
briandg is offline  
Old July 26, 2018, 02:14 AM   #11
44 AMP
Staff
 
Join Date: March 11, 2006
Location: Upper US
Posts: 28,617
Generally speaking bullet makers consider 100/105gr .243 to be deer bullets. Some make 90-95gr deer bullets. Go lighter and they are usually made to be varmint bullets. When in doubt, ask the maker.

Try different brands & weights, until you find one that shoots well enough for your needs in her rifle. I knew a fellow who took 6 elk with a .243 and "deer bullets", but he was willing to pass any but a perfect neck shot.

The .243 has a long and deserved reputation as a good, low recoil deer round, with the right bullets.
__________________
All else being equal (and it almost never is) bigger bullets tend to work better.
44 AMP is offline  
Old July 26, 2018, 05:00 AM   #12
hooligan1
Senior Member
 
Join Date: July 18, 2010
Location: Independence Missouri
Posts: 4,582
I have a nice little .243 win that likes 100 grain Gamekings and Winchester Supreme 780, shoots under moa at 100 yds consistently.
__________________
Keep your Axe sharp and your powder dry.
hooligan1 is offline  
Old July 28, 2018, 03:35 PM   #13
Paul B.
Senior Member
 
Join Date: March 28, 1999
Location: Tucson, AZ
Posts: 3,790
Back in the mid to late 70's when I lived in Nevada, I used to take some of the neighbor kids out on their first deer hunts. They used my .254 shooting the 100 gr. Hornady Interlocks just fine. Five kids on five different hunts, five shots and five dead deer. It worked for them so should work just fine for your wife. I used it mostly to shoot coyotes on private ranches as a favor to the ranchers. Never did shoot a deer with it for some reason or another. I forge the load but it with either H or IMR 4350. All my years worth of loading notes were lost during the move from Nevada to Arizona.
Paul B.
__________________
COMPROMISE IS NOT AN OPTION!
Paul B. is offline  
Old August 6, 2018, 07:39 PM   #14
ReloadKy
Senior Member
 
Join Date: February 23, 2018
Posts: 191
Update: because i have had luck with hornady SST's for other calibers and because my local shop had them in stock i decided to give the 95 gr Hornady SST's a try. I loaded them with 44 gr of R19 (max load per Hornady manual). On my wife's second trip to the range she put 3 shots dead center 2 inches high. the group measured 0.410 inches. I was really proud. My wife really didn't understand how good of a group that was but she liked shooting the rifle. Thanks for all suggestions. I really enjoy being a part of this forum.
ReloadKy is offline  
Old August 6, 2018, 08:00 PM   #15
ligonierbill
Senior Member
 
Join Date: May 20, 2007
Posts: 2,427
Glad it's shooting well. Maybe I misunderstood, but didn't you mean to say you worked up to the max load. The way I read it, you went straight to max.
ligonierbill is offline  
Old August 6, 2018, 08:01 PM   #16
std7mag
Senior Member
 
Join Date: June 23, 2013
Location: Central Taxylvania..
Posts: 3,609
Glad you found a load you, and more importantly she likes.
__________________
When our own government declares itself as "tyrannical", where does that leave us??!!

"Januarary 6th insurrection".
Funny, I didn't see a single piece of rope...
std7mag is offline  
Old August 8, 2018, 05:40 PM   #17
LE-28
Senior Member
 
Join Date: September 24, 2012
Location: North Carolina
Posts: 758
If that load ever doesn't work out for you check out 40gr of Imr4350 with a 100 gr Sierra game king bullet loaded to her rifle for length.

My family has a standing 100% success rate with this load in everything from a 1946 Model 70 Winchester to a 1990 Savage 110G on everything from groundhog to whitetail dear.

A water snake, many muskrats, and several snapping turtles at 125yds give or take from our 1 acre farm pond from our front porch.

Disclaimer: The snappers took a few days to come floating up after being shot. That's normal for a turtle.

The groundhogs was our passion in life with the .243s.

Whitetail just weren't a problem worth noting.
LE-28 is offline  
Old August 11, 2018, 11:52 AM   #18
CarJunkieLS1
Senior Member
 
Join Date: October 1, 2013
Posts: 686
This is a simple answer the 90 grain Nosler Accubond. And practice with the cheaper 90 Ballistic Tip
CarJunkieLS1 is offline  
Old August 19, 2018, 12:21 PM   #19
mw0248
Junior Member
 
Join Date: August 18, 2018
Posts: 3
I reload 95 gr. nosler ballistic tips in my .243; drops em like a rock
mw0248 is offline  
Old August 23, 2018, 09:30 AM   #20
DJudge
Junior Member
 
Join Date: August 22, 2018
Posts: 4
I'm having good luck with 95 grain SSTs over a moderate charge of 4350.
DJudge is offline  
Old August 24, 2018, 08:32 PM   #21
ReloadKy
Senior Member
 
Join Date: February 23, 2018
Posts: 191
DJudge, have you shot any deer with them yet? Was curious to on game performance.
ReloadKy is offline  
Old August 25, 2018, 04:57 AM   #22
BeeShooter
Member
 
Join Date: August 24, 2016
Posts: 85
An 80 grain bullet in a .243 will work just as good as a 100 grain for all practical deer hunting situations.
BeeShooter is offline  
Old August 26, 2018, 04:28 PM   #23
BWM
Senior Member
 
Join Date: November 6, 2013
Location: SW IN
Posts: 438
I like the 100gr soft point it does a very good job and has done for years There is some new out there that will do a good job like the Sierra SBT Gameking 100gr they are a accurate bullet. Good Luck
__________________
Man that likes guns. Navy. USS Ponchatoula AO 148 USS Vesuvius AE 15
BWM is offline  
Old September 4, 2018, 11:00 AM   #24
DJudge
Junior Member
 
Join Date: August 22, 2018
Posts: 4
ReloadKY…. No, not yet just recently began exploring the capabilities both the .243 Win and 6.5 Grendel for an accurate light weight and light recoiling platform for use in the future by the grandchildren. Overall results by both rounds are very impressive so far and I began using SST's due to others comments and results of actual harvest on deer and hogs.
DJudge is offline  
Old September 7, 2018, 10:49 AM   #25
FiveInADime
Senior Member
 
Join Date: January 25, 2012
Posts: 607
Quote:
Originally Posted by Panfisher View Post
I reload for my wife's Ruger .243. I load 100 grain Hornady Inter lock over 34. Grains of IMR 4895. Very mild load that she has zero issues shooting, and will absolutely pound deer and punch through both shoulders. The load has never been bench rest accurate but she keeps her shots at 100 yards or less and is deadly.
I want to load that bullet but I need to push it a bit faster than that. Thinking RL17 because I have some. This is for a Coues deer hunt in central Arizona so cross-canyon shots are the norm.



Sent from my SM-G965U using Tapatalk
FiveInADime is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:00 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.06626 seconds with 8 queries