The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools Search this Thread
Old March 14, 2019, 07:17 PM   #1
HappyTrap687*
Junior Member
 
Join Date: January 5, 2019
Posts: 2
Ruger GP100 .22 LR

My Ruger has an estimated 1000 rounds thru it. About 1 in 10 or 1 in 20 shells do not fire. It has the original hammer spring. No other mods. The holes where no firing occurs are random. The cylinder seems to be very tight with not more than .005 movement. Visually there is no dirt or other problem. It seems to me the rims have a very small dimple in them when fired. Based on the observation of my Trailside or High Standard it is a wonder any of them fire at all. I have used Remington, Winchester, And Aguila run of the mill cheap ammo. Can anybody give me any ideas on how to fix my non-firing problem.
HappyTrap687* is offline  
Old March 14, 2019, 07:20 PM   #2
4V50 Gary
Staff
 
Join Date: November 2, 1998
Location: Colorado
Posts: 20,284
Try better ammo. Clean it. Dirty guns don't work well. Could be a burr somewhere. However, if it works with good quality ammo, it's the cheap ammo your Ruger doesn't like.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe!
4V50 Gary is online now  
Old March 14, 2019, 07:20 PM   #3
weblance
Senior Member
 
Join Date: October 3, 2012
Posts: 1,217
Send it back to Ruger
weblance is offline  
Old March 14, 2019, 11:46 PM   #4
ballardw
Senior Member
 
Join Date: September 19, 2008
Posts: 539
Did you try a second time to fire any of those with apparent light strikes without removing them from the cylinder? A close to minimum spec chamber diameter and near maximum spec diameter ammo sometimes means that cases do not quite seat as deep as they should into the chamber. The first attempt to fire may seat the cartridge deeper in to cylinder and the slight movement means not enough energy was transferred to ignite the primer. If the second attempt has them fire this becomes one likely scenario.

A small amount of un-burnt powder or fouling build up might cause this. Hence the suggestion to clean it.

I know that some brands of ammo I have noticed it sometimes takes a little push to seat into my Ruger Single-Six chambers, not just "drop in" like you might want.
__________________
-+-+-+-+-+-+-+-+-+-+-+-+-+-+
All data is flawed, some just less so.
ballardw is offline  
Old March 15, 2019, 08:46 PM   #5
berettaprofessor
Senior Member
 
Join Date: November 23, 2008
Posts: 913
That was a known problem with the GP100's when they first came out. Sending it back to Ruger seemed to be the only real solution. I traded mine when I finally came to the realization that I didn't want a 22LR that heavy.
berettaprofessor is offline  
Old March 16, 2019, 02:56 PM   #6
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 13,557
I bet it happens primarily when shooting single action. One problem I've encountered with Ruger revolvers is the transfer bar being a little short and not reaching completely over the firing pin. When shooting double action, people tend to follow through pretty well, but in single action they tend to just pull the trigger enough to barely enough to release the hammer, so the transfer bar isn't always up over the firing pin when the hammer strikes.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Taylor Machine
Scorch is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:58 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.04819 seconds with 10 queries