The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Reply
 
Thread Tools Search this Thread
Old April 28, 2018, 01:06 PM   #1
Jakeway
Member
 
Join Date: October 12, 2017
Location: Near Nashville, TN
Posts: 50
My first Single Action

Today I bit the bullet (figuratively) and bought a Uberti Cattleman II in 45 LC. I got out of work early yesterday and stopped at gun store about 40 minutes from my house, where I hadn't stopped in years. They had several Ubertis in stock, and the guy working there actually had personal experience with both SA cartridge guns and BP revolvers and was able to answer all my questions.

At first I was interested in a fine 7.5" barrel for only $439, but then I noticed a 5.5" model with pretty nice looking curly grain in the walnut grips. I thought about it all night, and I kept going back to those nice looking grips. I decided the nicer wood was worth the 10% higher price on that particular gun, so I went back this morning and bought it.

Tomorrow morning I'll go to my buddy's farm and shoot it...maybe in the sunshine I'll get some pics to post.
Jakeway is offline  
Old April 28, 2018, 01:30 PM   #2
bedbugbilly
Senior Member
 
Join Date: November 19, 2009
Posts: 3,118
I have a 7 1/2" Uberti Cattleman in 45 Colt - a great revolver. I have a Uberty Bisley in 357 - 5 1/2" barrel - both excellent shooters.

In my Cattleman, I use the Lyman/Ideal 454-190 over either Red Dot or Unique. It show awesome at 25 and 50 yards if I do my job.

You'll Like your Uberti - and the 45 Colt is an easy cartridge to reload in either Bp or Smokeless.
__________________
If a pair of '51 Navies were good enough for Billy Hickok, then a single Navy on my right hip is good enough for me . . . besides . . . I'm probably only half as good as he was anyways. Hiram's Rangers Badge #63
bedbugbilly is offline  
Old April 28, 2018, 08:01 PM   #3
Hawg
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 14,787
You're going to love it.
Hawg is offline  
Old April 29, 2018, 08:53 AM   #4
stinkeypete
Member
 
Join Date: July 22, 2010
Location: Madison, Wisconsin
Posts: 52
You did well

Personally, I prefer the barrel length around 5 inches until one starts in to those “Ruger Only” power levels. After exploring that as far as it will go, I came around to my present stance of “9 grains of unique is plenty enough.”

Enjoy. Even a very light load in .45 Colt is no joke, and I hope you enjoy.
stinkeypete is offline  
Old April 29, 2018, 05:17 PM   #5
Driftwood Johnson
Senior Member
 
Join Date: January 3, 2014
Location: Land of the Pilgrims
Posts: 1,717
Howdy

Just curious.

Does it have the new retractable firing pin in the hammer, or does the firing pin stay put in the hammer?
Driftwood Johnson is offline  
Old April 29, 2018, 08:55 PM   #6
Jakeway
Member
 
Join Date: October 12, 2017
Location: Near Nashville, TN
Posts: 50
It has the retractable firing pin. I don't think I like it. The trigger has much more creep and is heavier than either of my Pietta Cap & Ball revolvers. I only shot 25 rounds today. I got about a three inch group at 20 yards when using a rest, but the group was about 3" low at that range. Off hand I only hit an 8" steel plate 2 out of 5 shots.

Also, two of the primers pierced; you can see light through it. The other 23 rounds had very deep dents in the primers. Winchester 250 gr Cowboy Action loads.
Jakeway is offline  
Old April 30, 2018, 09:27 AM   #7
Trum4n1208
Senior Member
 
Join Date: September 13, 2013
Posts: 166
According to a gentleman I exchanged emails with at Cimarron Firearms, all of the Uberti SAA repro revolvers will be switched over to the new firing pins this year, including the 'Old Model' revolvers. So if you want them with the fixed firing pin then get them now.

Jakeway, you might be able to buy one of the older hammers off of VTI gunparts and switch them out.
Trum4n1208 is offline  
Old May 2, 2018, 03:35 PM   #8
Jakeway
Member
 
Join Date: October 12, 2017
Location: Near Nashville, TN
Posts: 50
Will need new hammer and also either new trigger or modify the old one. It might be better to do something to make the firing pin fixed in place.

If the heavier trigger pull I'm experiencing is caused b something other than the additional resistance of the "safety pin" inside the hammer, then I'll just keep it as is.
Jakeway is offline  
Old May 2, 2018, 07:19 PM   #9
Jakeway
Member
 
Join Date: October 12, 2017
Location: Near Nashville, TN
Posts: 50
Pics don't do it justice; the curls change as the light angle changes.



Jakeway is offline  
Old May 2, 2018, 11:04 PM   #10
4V50 Gary
Staff
 
Join Date: November 2, 1998
Location: Colorado
Posts: 20,111
Nice stocks
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe!
4V50 Gary is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:50 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.05646 seconds with 10 queries