The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting > Bullet Casting

Thread Tools Search this Thread
Old June 2, 2018, 07:33 AM   #1
Senior Member
Join Date: April 15, 2018
Location: DFW area - north Texas
Posts: 135
Dallas area ranges that allow backstop mining?

Later this fall I'd like to do some backstop mining to pick up some lead.

Does anyone know of any ranges that allow backstop mining or even that sell lead to customers in the greater Dallas / Fort Worth area?

The in door ranges I have asked have contracts for both lead & brass and don't sell to customers.
Grey_Lion is offline  
Old June 4, 2018, 03:51 PM   #2
the Black Spot
Senior Member
Join Date: September 9, 2009
Location: arkansas
Posts: 185
Might try Garland Shooting Range
the Black Spot is offline  
Old June 6, 2018, 09:36 PM   #3
Senior Member
Join Date: October 16, 2014
Location: Iowa
Posts: 1,044
I'd visit them or call around. The local indoor range I visit sells to someone who cast fishing sinkers and he pays $2 per pound. I've found numerous sellers at $1 per pound and can have stuff delivered to my door for less than $2 per pound. I've found most my lead on Craigslist.
reddog81 is offline  
Old June 7, 2018, 04:08 PM   #4
Senior Member
Join Date: August 25, 2008
Location: Potatoes and Hops
Posts: 11,334
Unless you are part-owner of a private range, or very good friends with the owner(s), you'll probably not find a range that will "allow" backstop mining.

There are some ranges that look the other way if it is done (safely and responsibly); but actually getting permission and approval is highly unlikely as a stranger.
Don't even try it. It's even worse than the internet would lead you to believe.
FrankenMauser is offline  
Old June 10, 2018, 05:27 PM   #5
Senior Member
Join Date: April 15, 2018
Location: DFW area - north Texas
Posts: 135
I spent my morning at Proactive in Argyle, TX this morning and they seemed amenable to me doing some backstop mining this winter.
Grey_Lion is offline  
Old June 21, 2018, 04:22 PM   #6
Senior Member
Join Date: November 30, 2012
Location: Baton Rouge, Louisiana
Posts: 804
Check with some of the indoor shooting ranges. These have steel bullet traps , the baffles direct the bullets down into a trough....the bullets are scooped out. No digging.
Our local range sells the lead to the scrap yard but will sell it a reloader for the same price.
gwpercle is offline  
Old June 21, 2018, 06:17 PM   #7
Senior Member
Join Date: April 15, 2018
Location: DFW area - north Texas
Posts: 135
The indoor range I frequent has a backstop of ground up aircraft tires ( no metal banding in those ) and they have a service contract for all their brass and lead and don't sell any to shooters. :-(

Should I some day set up a range of my own, I plan to have a thick steel plate hanging in a tractor tire as my backstop with a frame to hold paper targets. All the lead collects at the bottom of the tire.

I've also recently seen a steel target where the first 5 go back and lock when hit and the sixth releases the first 5 back down. - Put a metal trough under that to catch the rounds.
Grey_Lion is offline  
Old June 21, 2018, 08:53 PM   #8
Senior Member
Join Date: May 4, 2010
Posts: 5,047
an earthen berm would take so much damage from people digging through it that I can't imagine anyone allowing it.
briandg is offline  
Old June 22, 2018, 01:20 PM   #9
Senior Member
Join Date: November 20, 2007
Location: South Western OK
Posts: 2,743
i can't imagine a range owner allowing the "mining" of lead from berms. It could be a liability issue if the "miner" came down with lead poisoning.

A much better source of lead is roofing contractors.
thallub is offline  
Old June 22, 2018, 06:51 PM   #10
Senior Member
Join Date: April 15, 2018
Location: DFW area - north Texas
Posts: 135
I've mined a private berm and it is quite a bit of work. All the non-magnum pistol rounds and most of the 223 rifle rounds were in the first 5 to 6 inches.

As for lead poisoning - most people very much over-blow this threat. Don't smelt indoors, don't eat or drink while smelting or casting. Don't use any smelting gear for cooking later. Don't do any smelting or casting in your kitchen.

I've been casting lead for some 2 decades now and I've had my lead level tested and have been pronounced in good health with no elevated lead levels.

So mining a berm is not something I have a fear will give me lead poisoning.

In my experience, the biggest concern, besides deforming the berm, that range owners seem to have is what's done with the contaminated scrap - i.e. the copper jackets. Typical answer is to put that back into the berm.

If you have a smelting pot cooking over an open fire pit - flux it with saw-dust, and cast ingots there, you can put the jacket pieces back where you found them in the berm and you aren't materially changing anything except recycling the bulk of the lead. I make round ingots in small muffin tins picked up at goodwill.
Grey_Lion is offline  
Old July 16, 2018, 07:25 PM   #11
Senior Member
Join Date: December 14, 2011
Location: WV
Posts: 937
We’ve got two state ran gun ranges. Both outdoor. I bet there’s literally tons of lead there. I wonder if I could sift some dirt.
WV_gunner is offline  

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -5. The time now is 07:14 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent:
Contact Us
Page generated in 0.06007 seconds with 10 queries