|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
June 8, 2020, 01:10 PM | #1 |
Junior Member
Join Date: June 8, 2020
Posts: 5
|
Help with new 9mm mag adapter for AR build. Doesn't fit!
Hi all. Purchased a 9mm mag well adapter from KAK for my PSA PA-15 Multi lower receiver. It's way too snug. My lower is mil-spec so I wonder if anybody has had problems fitting 9mm adapters that are available out there. I got it in about a third of the way and it's not going in without the hammer and damaging something. Had to punch it back out. KAK says they will accept a return but I'm thinking I could try filing it or sanding it first. I have a needle file set and sandpaper. I would appreciate some guidance trying to sand or file this thing down and what to expect before I go to town on it. It comes apart easily and the metal faces underneath the lip of the feed ramp probably need less than a millimeter taken off. My local gunsmith said they don't want to mess it up and void any warranty so I'm on my own here.
Thought about buying a different one from another seller but all the pictures look the same as the one I have so I feel like I'd be swapping adapters for the same one that doesn't fit. Looks like they're all made by GunTech. I saw Hahn makes one but $200 is kinda ridiculous. Share your experience here please. Thanks P.S. I've tried a Pro Mag brand adapter and they jam up the feed. |
June 8, 2020, 01:50 PM | #2 |
Senior Member
Join Date: October 19, 2005
Location: Tx Panhandle Territory
Posts: 4,159
|
Did it leave any marks to show where it was hanging up?
__________________
Rednecks... Keeping the woods critter-free since March 2, 1836. (TX Independence Day) I suspect a thing or two... because I've seen a thing or two. |
June 8, 2020, 02:22 PM | #3 |
Junior Member
Join Date: June 8, 2020
Posts: 5
|
It's just a bit too long in the front I believe. Also I should've mentioned this before it's a COLT/SMG mag adapter not Glock. Appears to be good clearance for ejector hook rear side with the offset form for bolt catch that runs up the cutout of the magwell. I can see daylight around the sides as well. It's the front face of the adapter that sits flush against the front of the magwell where the feed ramp is housed that I believe needs a little shaving.
The adapter is two pieces held together by allen screws, roll pins inside holding feed ramp and LRHO pieces. I could file or sand those front faces but I've never tried this before and figured someone may have encountered this issue. I don't know how easy it really is to file or sand metal, though I guess it's just aluminum metal. From the lip of the front of the feed ramp to the edge of the front housing is just a few millimeters. Thinking that I could file or sand those faces flush to the lip of the feed ramp and it would fit a lot easier. Definitely don't want an adpater I have to force in as this defeats the purpose of being able to easily switch calibers back to 556 with another upper |
June 8, 2020, 02:35 PM | #4 |
Junior Member
Join Date: June 8, 2020
Posts: 5
|
Here are a few pics.
You can see the front faces I think I could file or sand down to almost flush with the feed ramp. The top of edge has scratches you can barely see. From the back you can see the scratch on top left of the offset that happens when I try to shove this puppy in the magwell. (No I did not try to install with the top screw and washer still on it, I put them back on afterwards to keep from losing them) |
June 8, 2020, 02:39 PM | #5 |
Junior Member
Join Date: June 8, 2020
Posts: 5
|
Had to resize the photos, oops.
|
June 8, 2020, 02:51 PM | #6 |
Senior Member
Join Date: July 10, 2007
Location: Dayton OH
Posts: 155
|
You put it in from the top of the lower correct? ("Top" being, take the upper off and drop it in?)
|
June 8, 2020, 03:20 PM | #7 |
Junior Member
Join Date: June 8, 2020
Posts: 5
|
It's designed to install from the bottom. Right now I have the the bolt catch uninstalled on my lower so I could try both top and bottom. Just not a good fit.
|
June 10, 2020, 02:42 AM | #8 |
Senior Member
Join Date: August 24, 2001
Location: LC, Ca
Posts: 1,917
|
Do you have another AR-15 lower you could try?
|
June 11, 2020, 06:57 PM | #9 |
Staff
Join Date: November 2, 1998
Location: Colorado
Posts: 21,824
|
First of all, return it before you start filing away. It's their problem, not yours.
Second, If they were out of business, I'd smoke fit it. Apply smoke, insert, where the smoke is rubbed off file. Repeat as necessary. But this is only if they were out of business. Don't try this because they'd probably tell you they won't take it back after you filed away on. it. BTW, those washers look suspicious to me. Are they overlapping the magazine adapter? (But remember, send it back).
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe! |
Thread Tools | Search this Thread |
|
|