|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
December 6, 2012, 07:16 PM | #1 |
Senior Member
Join Date: January 9, 2012
Location: The Great State of Texas
Posts: 210
|
Blazer aluminum case out of a Rossi 38 sp
I picked up an old rossi interarms 38 special (not +P rated) from a cop for $100 including 45 rounds of ammo. It was his backup and only ever shot 5 rounds out of it. I've put a few hundred thru it and its a good little snubby. I just bought a box of blazer ammo for $12. Turns out it has aluminum casing (I know, I know, I should have read the box first). I don't reload so don't really care about that part. I know steel casing can screw up a good weapon and wanted to see if aluminum casing would be an issue out of my Rossi.
Secondly, since I can't use +P what would be the best self defense ammo to use in it? |
December 6, 2012, 07:52 PM | #2 |
Senior Member
Join Date: March 11, 2012
Location: Wendell, N.C.
Posts: 189
|
The aluminum cased ammo will not harm your revolver. I have been using Federal 125 grain Nyclads for several years but recently started experimenting with the Hornady 158 grain XTP jacketed hollow point. It is a standard velocity round running about 725 fps from my Colt Agent. Recoil is fairly mild allowing quick follow up shots and testing shows good penetration and expansion to about .526 diameter. I may start carrying that as my defensive load. Most .38's are regulated at the factory to shoot 158 grain to POA. My Agent does with this round.
|
December 6, 2012, 07:55 PM | #3 |
Senior Member
Join Date: February 22, 2008
Location: SW Washington state
Posts: 1,996
|
They may stick
I have seen the Blazer aluminum case stick in the chambers of revolvers. Not a big deal. Just make sure you support the cylinder well when you tap the case out with an appropriate size hardwood dowel. Otherwise you could damage the crane.
__________________
ricklin Freedom is not free |
December 6, 2012, 08:39 PM | #4 | |
Senior Member
Join Date: April 22, 2007
Posts: 1,996
|
Quote:
|
|
December 6, 2012, 09:47 PM | #5 | |
Senior Member
Join Date: October 20, 2007
Location: Richardson, TX
Posts: 7,523
|
Quote:
They DO generally "shoot dirty" because the stiffer steel case does not provide as tight of a gas seal as a brass or aluminum case. OTOH far and away the main problem with steel-case ammo is that most brands also incorporate steel jackets and/or cores in the bullets. These ricochet more often, they chew up the steel target hangers and backstops at indoor ranges, and the sparks create a heightened risk of wildfires at outdoor ranges and paper scrap fires at indoor ones. Consequently, an increasing number of shooting ranges prohibit their use.
__________________
"Smokey, this is not 'Nam. This is bowling. There are rules... MARK IT ZERO!!" - Walter Sobchak |
|
December 6, 2012, 10:47 PM | #6 |
Senior Member
Join Date: January 9, 2012
Location: The Great State of Texas
Posts: 210
|
Thanks for the help and tips guys.
|
December 6, 2012, 11:59 PM | #7 |
Senior Member
Join Date: November 25, 2008
Location: California
Posts: 1,951
|
I have shot hundreds of rounds of Blaser 44spl 200gr Gold dots out of my 44mag with no problems.
__________________
http://www.armsmaster.net-a.googlepages.com http://s239.photobucket.com/albums/f...aster270/Guns/ Retired LE, M.P., Sr. M.P. Investigator F.B.I. Trained Rangemaster/Firearms Instructor & Armorer, Presently Forensic Document Examiner for D.H.S. |
December 7, 2012, 02:01 PM | #8 |
Senior Member
Join Date: November 2, 2005
Location: Arizona
Posts: 1,936
|
There are those who have had problems with Blazer Aluminum ammo, I think I have used 90 percent of the different loadings over the years, everything from the .25 ACP to .45 Colt, No 44 yet. I really can't think of a single problem that I've been able to associate with the aluminum casing. That is just my experience. Even if you have sticky cases because of a very tight chamber, it wont hurt your firearm in any way. Any problems encountered will more than likely because your revolver is a Rossie rather than aluminum ammo casings.
__________________
Ron James |
December 7, 2012, 06:03 PM | #9 |
Senior Member
Join Date: January 2, 2005
Location: Where the deer and the antelope roam.
Posts: 3,082
|
A good 158 grain semi wadcutter is probably the best in a standard pressure 38 special. You do not generally have enough velocity from a standard pressure 38 special fired from a snub nose barrel to ensure expansion so use a bullet that does not need expansion to be effective.
The two last picks for SD are the LRN and the 148 WC, both are dismal performers, the wound may be fatal but I do not feel like waiting a week. I do not see where some +p 38's would hurt if they were only used for SD and not regular practice.
__________________
Retired Law Enforcement U. S. Army Veteran Armorer My rifle and pistol are tools, I am the weapon. |
December 7, 2012, 06:09 PM | #10 |
Senior Member
Join Date: November 2, 2005
Location: Arizona
Posts: 1,936
|
Nanuk, he was worried that aluminum cased Blazers would harm hs new " used " Rossie . Not which bullet is best .
__________________
Ron James |
December 7, 2012, 07:55 PM | #11 | |
Senior Member
Join Date: June 4, 2012
Location: NV
Posts: 743
|
Quote:
|
|
Thread Tools | Search this Thread |
|
|