Smith and Wesson serial number search - Page 31

misanthropic777 · December 20, 2008, 05:42 PM

Got a manufacture date question on another one:

S&W pre-model 10 w/ 5" barrel. Serial # C 1347xx on butt of grip. Marked "SMITH & WESSON" on left side of barrel, "38 S.&W. SPECIAL CTG." on right barrel. S&W trademark on right side of frame, rear; on front "MADE IN USA/MARCAS REGISTRADAS/SMITH & WESSON/SPRINGFIELD, MASS." Number(s) on yoke is 60139.

thanks!

laytonj1 · December 20, 2008, 06:03 PM

Quote:

S&W pre-model 10 w/ 5" barrel. Serial # C 1347xx on butt of grip

C1 thru C239999 were made from 1948 to 1952.

Jim

MikeKeyW · December 20, 2008, 06:43 PM

I have a 32 S&W Long, C 68771. It has 5 screws and a "J" stamped on the right side of the grip frame along with inspector stamps there and on the left. It is square butt and 5" tapered bbl. I understand it's somewhat rare but falls outside the range of serial #'s of others I've seen online with a higher # by about 10,000. Looks like my letter from Roy will be a while in coming. Any ideas?

lonestarmod64 · December 20, 2008, 08:47 PM

I just got a S&W Mod.64-5 ser.#BRL73xx i was wondering how old it is and it has a bobbed hammer spur would it have came from the factory that way. The lock up is tight and has a clean bore. I don't know much about revolvers but I paid $220.00 for it was that a fair price. Thanks for any input on this gun.

ockfish · December 21, 2008, 08:34 AM

I am needing help too!! My neighbor has a smith revolver that he is willing to sell and I NEED to know about how old it is.

It's a 32 Long and has either OTG or CTG on the barrel. ( I Know nothing about revolvers). It has the S&W trademark. serial # is 461XXX

Thanks soooo much!

2sigs · December 21, 2008, 10:59 AM

Quote:

32 S&W Long, C 68771

I think it falls in the 2nd change of .32 Hand Ejector series 1906-09
that # would be 1908 roughly
However without alot more info such as all barrel stampings and locations of such also stamping on left or right side of frame.
Also I'm not to sure of the 5" barrel, the barrel on a revolver is measured from the end of the cylinder face to the end of the barrel.

Quote:

S&W Mod.64-5 ser.#BRL73xx

The mod. 64-5 was production change that took place and run for aprox. 10 yrs. til 1998 when the 64-6 was introduced. without more information such as the star extractor or newer design changed 1994. Square butt was ended in 1995-96 and the MIM trigger 1997.
So with that info maybe you can help yourself with very aprox. date of Manufacture.

Have a Merry Christmas everyone!
-2sigs

laytonj1 · December 21, 2008, 02:44 PM

Quote:

I have a 32 S&W Long, C 68771. It has 5 screws and a "J" stamped on the right side of the grip frame along with inspector stamps there and on the left. It is square butt and 5" tapered bbl. I understand it's somewhat rare but falls outside the range of serial #'s of others I've seen online with a higher # by about 10,000. Looks like my letter from Roy will be a while in coming. Any ideas?

Your SN dates to the early part of the 1948 to 1952 era, which is the same time period some 32 Long M&P's were made. You may also find some info by posting this question and /or doing a search on the S&W forums.
http://smith-wessonforum.com/eve/

Quote:

I just got a S&W Mod.64-5 ser.#BRL73xx i was wondering how old it is and it has a bobbed hammer spur would it have came from the factory that way

~1994. There were several bobbed versions made for the various police departments over the years so it's possible.

Quote:

It's a 32 Long and has either OTG or CTG on the barrel. ( I Know nothing about revolvers). It has the S&W trademark. serial # is 461XXX

Round or square butt? Any patent dates on top of barrel?

Jim

Fry1807 · December 21, 2008, 04:04 PM

What about a pre-victory .38 S&W 6 inch barrel with serial 696XXX

laytonj1 · December 21, 2008, 05:06 PM

Quote:

What about a pre-victory .38 S&W 6 inch barrel with serial 696XXX

38 Military and Police of 1905, 4th Change with SN's from 241704 in 1915 to SN 1000000 in 1942.

Jim

oklahoma mick · December 21, 2008, 07:25 PM

could someone date this smith for me ? I am going to buy that book but havent yet . ser # 139xxx thanks

ockfish · December 21, 2008, 08:10 PM

Quote:

Quote:
It's a 32 Long and has either OTG or CTG on the barrel. ( I Know nothing about revolvers). It has the S&W trademark. serial # is 461XXX

Round or square butt? Any patent dates on top of barrel?

I am pretty sure it was round and had 3 patent dates--the latest one was 1914 i think.
That's all I can remember. Thanks so much!

laytonj1 · December 22, 2008, 01:35 AM

Quote:

could someone date this smith for me ? I am going to buy that book but havent yet . ser # 139xxx thanks

It's either a 1st or 2nd change made from 1906 to 1909

Quote:

I am pretty sure it was round and had 3 patent dates--the latest one was 1914 i think.
That's all I can remember.

Okay, sounds like a .32 Hand Ejector Third Model. SN's ran from 263001 in 1917 to 536684 in 1942. So probably 1930's.

Jim

Laker · December 22, 2008, 06:22 PM

What the heck. This seems like the place to inquire S&W 65-2 #1D70XXX.Thanks

ockfish · December 22, 2008, 11:04 PM

Thanks Jim!!

laytonj1 · December 22, 2008, 11:37 PM

Quote:

What the heck. This seems like the place to inquire S&W 65-2 #1D70XXX

1979/80

Jim

Evader · December 23, 2008, 12:38 AM

Hello,

I am new member to this site and I'm hoping someone can be of some help. I have recently inherited 2 handguns from a relative that has passed away.

#1 is a S&W .38 SPL Serial Number J984769

#2 is .22 Astra-Uncetay CIA S.A.-GUERNICA the words ASTA and CUB are engraved on the grip Serial Number 155770

I'm looking to see what the approx resale value of these guns might be and also how I would go about determining whether they are actually registered etc.

laytonj1 · December 23, 2008, 01:15 AM

Quote:

I am new member to this site and I'm hoping someone can be of some help. I have recently inherited 2 handguns from a relative that has passed away.

#1 is a S&W .38 SPL Serial Number J984769

#2 is .22 Astra-Uncetay CIA S.A.-GUERNICA the words ASTA and CUB are engraved on the grip Serial Number 155770

I'm looking to see what the approx resale value of these guns might be and also how I would go about determining whether they are actually registered etc.

The S&W was made in 1982. Value depends on condition ~$250 to $400.
As for the Astra, I don't have any references for them.
Registration depends on your local laws. I don't know were you live.

Jim

Evader · December 23, 2008, 10:19 AM

Jim,

Thanks for the helpful information. I live in Jersey but these would have been originally registered in Virginia Beach, Virginia. (assuming they were registered at all) My question would be if I attempt to register these in New Jersey will the "system" indicate whether the serial numbers are actually registered to my grandmother whom has since passed away?

Laker · December 23, 2008, 04:50 PM

Me too. Thanks Jim. Hopefully Santa will be bringing me the book.

laytonj1 · December 23, 2008, 10:57 PM

Quote:

Thanks for the helpful information. I live in Jersey but these would have been originally registered in Virginia Beach, Virginia. (assuming they were registered at all) My question would be if I attempt to register these in New Jersey will the "system" indicate whether the serial numbers are actually registered to my grandmother whom has since passed away?

No, because there is not a federal registration (one state wouldn't know or care about the other state). In most states and locals the paperwork you fill out when buying a gun goes no further than the dealer himself. When I lived in Virginia there was no gun registration. There are however some state, county and locals with registration laws but the data is for their use only. Clark County (Las Vegas, NV.) required all guns purchased and /or brought into the county to be registered with the sheriffs office. They would keep it on file but it went no further then them. If you moved out of the county no one would care or know.
Your best bet is to contact your local law enforcement and ask them if they require gun registration, hopefully talking to someone knowledgeable.
Here's a good site for some of the gun laws:
http://www.handgunlaw.us/

Jim

Hardin132005 · December 25, 2008, 07:28 AM

I recently recieved my Grandfathers Smith & Wesson .38 Special.. I want to know when it was made and a little more information about it. If anyone has the book and would like to help please e-mail me at
[email protected] thanks.

gclax1336 · December 25, 2008, 12:28 PM

hey, I just got my grandfathers S&W .38 special ctg revolver for christmas and I would like to know the year it was made and maybe even a value on it. Thanks

its serial number is 63xxx

BLK08ROCKERC · December 25, 2008, 01:27 PM

Quote:
"hey, I just got my grandfathers S&W .38 special ctg revolver for christmas and I would like to know the year it was made and maybe even a value on it. Thanks

its serial number is 63xxx"

Where did you find that number?? Look at the bottom of the frame(between the grips) and post that number.

laytonj1 · December 25, 2008, 03:43 PM

Quote:

I recently recieved my Grandfathers Smith & Wesson .38 Special.. I want to know when it was made and a little more information about it. If anyone has the book and would like to help please e-mail me at

Gonna need more information like serial number (bottom of grip butt) and how many rounds it holds, etc and a pic would be helpful.

Quote:

hey, I just got my grandfathers S&W .38 special ctg revolver for christmas and I would like to know the year it was made and maybe even a value on it. Thanks
its serial number is 63xxx

5 shot or 6? Value depends heavily on condition.

Jim

Karen Anne RN · December 25, 2008, 04:32 PM

I really don't know much about guns, but I do have the opportunity to purchase the following for my husband for his birthday, and wondered if anyone could please let me know what the manufacture date and value is of it. I would really appreciate it.
It's a S & W 32 number 4 top break, # 185xxx for $250.

Thank you,
Karen

December 20, 2008, 08:47 PM	#754
lonestarmod64 Junior Member Join Date: December 20, 2008 Posts: 1	Got a manufacture date question. I just got a S&W Mod.64-5 ser.#BRL73xx i was wondering how old it is and it has a bobbed hammer spur would it have came from the factory that way. The lock up is tight and has a clean bore. I don't know much about revolvers but I paid $220.00 for it was that a fair price. Thanks for any input on this gun.

December 21, 2008, 07:25 PM	#760
oklahoma mick Junior Member Join Date: December 12, 2008 Posts: 5	s and w m and p could someone date this smith for me ? I am going to buy that book but havent yet . ser # 139xxx thanks

December 22, 2008, 06:22 PM	#763
Laker Senior Member Join Date: August 20, 2008 Location: NW Ohio Posts: 367	65-2 What the heck. This seems like the place to inquire S&W 65-2 #1D70XXX.Thanks

December 23, 2008, 12:38 AM	#766
Evader Junior Member Join Date: December 23, 2008 Posts: 2	Helping looking up build year and value Hello, I am new member to this site and I'm hoping someone can be of some help. I have recently inherited 2 handguns from a relative that has passed away. #1 is a S&W .38 SPL Serial Number J984769 #2 is .22 Astra-Uncetay CIA S.A.-GUERNICA the words ASTA and CUB are engraved on the grip Serial Number 155770 I'm looking to see what the approx resale value of these guns might be and also how I would go about determining whether they are actually registered etc.

December 25, 2008, 07:28 AM	#771
Hardin132005 Junior Member Join Date: December 25, 2008 Posts: 1	Help I recently recieved my Grandfathers Smith & Wesson .38 Special.. I want to know when it was made and a little more information about it. If anyone has the book and would like to help please e-mail me at [email protected] thanks.

December 20, 2008, 05:42 PM	#751
misanthropic777 Junior Member Join Date: May 16, 2007 Posts: 6	Got a manufacture date question on another one: S&W pre-model 10 w/ 5" barrel. Serial # C 1347xx on butt of grip. Marked "SMITH & WESSON" on left side of barrel, "38 S.&W. SPECIAL CTG." on right barrel. S&W trademark on right side of frame, rear; on front "MADE IN USA/MARCAS REGISTRADAS/SMITH & WESSON/SPRINGFIELD, MASS." Number(s) on yoke is 60139. thanks!

December 20, 2008, 06:43 PM	#753
MikeKeyW Junior Member Join Date: October 12, 2008 Posts: 11	I have a 32 S&W Long, C 68771. It has 5 screws and a "J" stamped on the right side of the grip frame along with inspector stamps there and on the left. It is square butt and 5" tapered bbl. I understand it's somewhat rare but falls outside the range of serial #'s of others I've seen online with a higher # by about 10,000. Looks like my letter from Roy will be a while in coming. Any ideas?

December 21, 2008, 08:34 AM	#755
ockfish Junior Member Join Date: September 28, 2008 Location: Ky Posts: 5	I am needing help too!! My neighbor has a smith revolver that he is willing to sell and I NEED to know about how old it is. It's a 32 Long and has either OTG or CTG on the barrel. ( I Know nothing about revolvers). It has the S&W trademark. serial # is 461XXX Thanks soooo much!

December 21, 2008, 04:04 PM	#758
Fry1807 Junior Member Join Date: December 15, 2008 Posts: 12	What about a pre-victory .38 S&W 6 inch barrel with serial 696XXX

December 22, 2008, 11:04 PM	#764
ockfish Junior Member Join Date: September 28, 2008 Location: Ky Posts: 5	Thanks Jim!!

December 23, 2008, 10:19 AM	#768
Evader Junior Member Join Date: December 23, 2008 Posts: 2	Jim, Thanks for the helpful information. I live in Jersey but these would have been originally registered in Virginia Beach, Virginia. (assuming they were registered at all) My question would be if I attempt to register these in New Jersey will the "system" indicate whether the serial numbers are actually registered to my grandmother whom has since passed away?

December 23, 2008, 04:50 PM	#769
Laker Senior Member Join Date: August 20, 2008 Location: NW Ohio Posts: 367	Me too. Thanks Jim. Hopefully Santa will be bringing me the book.

December 25, 2008, 12:28 PM	#772
gclax1336 Junior Member Join Date: December 25, 2008 Posts: 2	hey, I just got my grandfathers S&W .38 special ctg revolver for christmas and I would like to know the year it was made and maybe even a value on it. Thanks its serial number is 63xxx

December 25, 2008, 01:27 PM	#773
BLK08ROCKERC Member Join Date: December 1, 2008 Location: Middle GA Posts: 27	Quote: "hey, I just got my grandfathers S&W .38 special ctg revolver for christmas and I would like to know the year it was made and maybe even a value on it. Thanks its serial number is 63xxx" Where did you find that number?? Look at the bottom of the frame(between the grips) and post that number.

December 25, 2008, 04:32 PM	#775
Karen Anne RN Junior Member Join Date: December 25, 2008 Posts: 2	Info request I really don't know much about guns, but I do have the opportunity to purchase the following for my husband for his birthday, and wondered if anyone could please let me know what the manufacture date and value is of it. I would really appreciate it. It's a S & W 32 number 4 top break, # 185xxx for $250. Thank you, Karen