March 15, 2012, 10:17 AM | #1 |
Senior Member
Join Date: November 14, 2011
Posts: 524
|
Best Spray Case Lube
What is everyone using for lubing cases with spray? About to start loading 5.56 and that would be alot of work to lube each case by hand. Also wanting to use it for my 308 brass
|
March 15, 2012, 10:52 AM | #2 |
Member
Join Date: November 30, 2011
Location: North Texas
Posts: 99
|
Hornady Case Lub (Spray). Use it on 223 & 270, love it.
|
March 15, 2012, 11:31 AM | #3 |
Senior Member
Join Date: May 9, 2011
Location: Boise, ID
Posts: 455
|
I used one shot.....Till this happened.
Now I use RCBS Case Slick. |
March 15, 2012, 12:57 PM | #4 |
Senior Member
Join Date: December 26, 2004
Location: Louisville KY
Posts: 13,806
|
I've found the Hornady Unique to be very easy to use and works a lot better than any spray lube I tried. A little on the fingers goes a long ways.
|
March 15, 2012, 01:27 PM | #5 |
Senior Member
Join Date: May 13, 2009
Location: Carrollton TX
Posts: 521
|
I use the Frankford Arsenal spray lube. I neck-size bottleneck cases and don't bother lubing pistol cases (carbide dies) so the only case I lube is the big-ol' 45-70. Never had a problem but you gotta follow the directions. As in, after you spray 'em down, let 'em sit for at least a minute or two. The stuff has to dry before it will work. When the cases "dry" they aren't really dry, but the alcohol has evaporated and you are just left with the lube, which is slightly greasy.
My process is this: I take a 1-gallon ziplock bag, spray in 1 spritz of FA lube, toss in 50 45-70 cases, zip the bag and roll them around, then dump them out into a plastic bin. Then I set up the press. By the time I get my press ready the cases are ready to go. I spray the lube in the bag before putting in the cases because I don't want lube getting inside the cases. It is supposed to not hurt anything but you can see the powder sticking to it inside the case if you look. So it makes me feel better if it just doesn't get a chance to get in there in the first place. -cls |
March 15, 2012, 02:36 PM | #6 |
Senior Member
Join Date: March 13, 2012
Posts: 127
|
+1 for RCBS Case Slick. I hold the lid for my lube pad over the shoulders when i spray so i dont get any on the necks/shoulder so i dont get dents from the dies.
tell you what you Really need is a dry lube for the Inside of the neck, i use white graphite from forster, best 20$ iv spent in reloading so far here |
March 15, 2012, 05:29 PM | #7 |
Senior Member
Join Date: March 13, 2009
Posts: 107
|
Royal Case & Die Lube...best aerosol lube there is.
|
March 15, 2012, 07:22 PM | #8 |
Senior Member
Join Date: April 18, 2000
Location: Metairie, Louisiana
Posts: 890
|
When I bought my RCBS press 30+ years ago I use RCBS pad and lube. Thick and sticky and it worked. When I bought my Dillon I bought Dillon spray lube. Works grate! Friend that used my equipment bought some Hornady spray lube. Works grate! So I believe any of the name brand spray lubes will work pretty well.
__________________
Guns are not dangerous! People are! RKBA! |
March 15, 2012, 07:29 PM | #9 |
Senior Member
Join Date: October 7, 2011
Location: Southern NM
Posts: 141
|
+1 on the Dillon case lube.
__________________
"Emergencies have always been the pretext on which the safeguards of individual liberty have been eroded" - F.A. Hayek |
March 15, 2012, 07:49 PM | #10 |
Senior Member
Join Date: June 30, 2009
Location: dallas
Posts: 773
|
Spray lubes are certainly the easiest and cleanest to use. Can't say its true in every single case, but if a shell sticks it because it didn't get enough lube, not that the lube wasn't any good. Most spray lubes are alcohol and some sort of lubricant like lanolin. You MUST keep it well shaken because the two do not stay mixed. After you spray, the alcohol evaporates leaving the lube behind. If you don't shake it up you just spray out the alcohol and get a stuck case.
|
March 15, 2012, 07:55 PM | #11 |
Senior Member
Join Date: October 17, 2006
Location: TX
Posts: 513
|
Hornady One Shot. Easy and works well. Cleans up nice too.
__________________
If you want to shoot...shoot...don't talk! Tuco USAF Munitions 1969-1992 RVN 1972-1973 |
March 15, 2012, 10:02 PM | #12 |
Member
Join Date: January 20, 2006
Posts: 55
|
stay away from one shot!
I also had a horrible experience with one shot spray lube - mangled a case, destroyed a die getting it out. Never again. It MIGHT be ok for pistol cases but it is definitely NOT for rifle brass!
I am sticking with the RCBS pad and roll on lube! |
March 15, 2012, 10:19 PM | #13 |
Senior Member
Join Date: February 14, 2008
Location: Kansas
Posts: 753
|
+3 for Dillon spray lube.
|
March 16, 2012, 12:07 AM | #14 |
Member
Join Date: July 14, 2005
Posts: 29
|
Dillon case lube which is lanolin and rubbing alcohol mixed together.
You can buy your own lanolin and 90%+ rubbing alcohol to make your own. I usually stick my cases into a zip lock bag. Give the Dillon bottle a few pumps inside the bag. then I seal up the bag and rock it back and forth to distribute the case lube. I always...ALWAYS! take a WD-40 soaked Q-tip and swirl that up inside the decapping/resizing die to clean it out at the start of every reloading session at each 100 round mark. |
March 16, 2012, 05:55 AM | #15 |
Senior Member
Join Date: January 12, 2012
Posts: 103
|
I tried the Hornady One Shot didn’t have any stuck cases but there was a sticky build up in the dies.(was about to have one) Switched to RCBS Case Slick very pleased. Dump cases in a gallon zip-lock bag spray, roll them around a little and good to go. The Hornady One Shot I tried was the one in the plastic pump spray bottle..
Last edited by Cornbread; March 16, 2012 at 05:47 PM. |
March 16, 2012, 06:43 AM | #16 |
Senior Member
Join Date: December 23, 2008
Location: Southern Illinois
Posts: 1,527
|
Hornady One Shot. People that get stuck cases don't use enough or don't get it where it needs to go. Period.
I am sure ANY spray case lube will work fine, as long as you understand where it needs to go on the case and how much to use. A little "spritz" is not near enough.
__________________
~~IllinoisCoyoteHunter~~ ~NRA LIFE MEMBER~ ~NRA CERTIFIED INSTRUCTOR~ |
March 16, 2012, 07:07 AM | #17 |
Senior Member
Join Date: June 21, 2009
Location: West Central Missouri
Posts: 2,592
|
I use Hornady One Shot.
Like others have said, follow the directions and shake the can! I ruined one dies because I was smarter than the can.
__________________
Inside Every Bright Idea Is The 50% Probability Of A Disaster Waiting To Happen. |
March 16, 2012, 08:56 AM | #18 |
Senior Member
Join Date: April 25, 2010
Location: Arkansas
Posts: 3,309
|
Dillon 5000
Enuf said. |
March 16, 2012, 10:07 AM | #19 |
Senior Member
Join Date: January 23, 2008
Location: Arsenal of Democracy
Posts: 405
|
I just sized 100 new 30/06 cases with one shot.....no stuck cases. I did notice where one or two got tight so I re lubed. And I think that was due a case being in the middle of the load block and not getting aa good spritz. Now I just pay close attention to my spray pattern.
__________________
I like to make beer, bullets, and jerky.....but not at the same time. Washed up 11B1P |
March 18, 2012, 06:12 PM | #20 |
Member
Join Date: July 2, 2007
Posts: 42
|
Just make SURE you shake the Can........
|
March 18, 2012, 07:36 PM | #21 |
Senior Member
Join Date: January 27, 2010
Location: AR
Posts: 1,401
|
I guess I dare to be different. I don't like spray lube. Yes, I tried it once and did not like the overspray and waste. I have been reloading well before spray case lube existed. Will stick with my pad and bottle.
|
March 18, 2012, 07:48 PM | #22 |
Senior Member
Join Date: January 23, 2008
Location: Arsenal of Democracy
Posts: 405
|
If you want to load bottle neck cartridges in a progressive press or an indexing turret press, the spray lube is the way to go.
__________________
I like to make beer, bullets, and jerky.....but not at the same time. Washed up 11B1P |
|
|