The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Revolver Forum

Reply
 
Thread Tools Search this Thread
Old October 10, 2012, 04:54 PM   #1
raindog
Member
 
Join Date: August 29, 2009
Posts: 69
For a .357Mag to reach full potential - how long a barrel?

I've read that a .357 Magnum revolver with a 2" barrel is not long enough for the round to reach its full potential. I'm not sure I understand why. When the charge ignites, the bullet starts moving forward. Does this mean that it escapes the barrel before the full force of the charge pushes it?

And on that note - how long is long enough for .357 Mag? 4"? 6"?
raindog is offline  
Old October 10, 2012, 05:05 PM   #2
MrBorland
Senior Member
 
Join Date: May 31, 2007
Location: NC
Posts: 2,614
Yes, pressure from the powder burn continues to push the bullet down the barrel, and the bullet leaves the barrel while still being pushed. In fact, a .357mag shot out an 18" rifle barrel gains velocity over a 6" revolver, so technically, it takes at least 18" for this cartridge to reach it's full potential. More relevant, then, is how much barrel do you need for your .357mag to do it's job.
MrBorland is offline  
Old October 10, 2012, 05:06 PM   #3
pete2
Senior Member
 
Join Date: May 15, 2012
Location: Texas
Posts: 2,566
You are right, it leaves the barrel before all the powder can burn. Normally, velocity in a 6" bbl will be higher than a 4" or a 2". This also applies to semi autos. There are exceptions, the gap between the face of the cylinder and the rear of the bbl can cause the velocity to be higher or lower than normal.
pete2 is offline  
Old October 10, 2012, 05:14 PM   #4
jmr40
Senior Member
 
Join Date: June 15, 2008
Location: Georgia
Posts: 10,792
http://www.ballisticsbytheinch.com/calibers.html

Click on the 357 mag icon and look at the different velocities based on barrel length.

Most of the published data you see is from 8" test barrels with no cylinder gap. Any rifle or handgun chambering needs some barrel length for all of the powder to burn. Most will burn within a few inches, but the pressure still builds up as the bullet passes through the barrels. A 357 from an 18-20" rifle barrel will be quite a bit faster than from even an 8" barrel. A 4" barrrel is only 1/2 the test barrels length and a 2" is 1/4. You will lose serious speed from barrels that short. A 2" barrel in most loadings is 500 fps or so slower than from an 8" barrel based on the above link. Almost 1000 fps slower than from an 18" rifle barrel in some loadings.

Also some cartridges use less powder, or are more efficeint and don't need as much barrel to reach their full potental. Magnum handgun chamberings with barrels less than 4" long are about useless for my purposes. Most of the published data for semi-autos is more accurate because they are tested in barrels closer to what people actually use. One reason the 9mm killed off 357 mag in law enforcement was when folks figured out their 6 shot 357 mags with 4" barrels were only shooting around 50 fps faster than a 15 shot 9mm when using the common 124/125 gr loadings.
jmr40 is offline  
Old October 10, 2012, 05:37 PM   #5
raindog
Member
 
Join Date: August 29, 2009
Posts: 69
Nice link, JMR - thanks.
raindog is offline  
Old October 10, 2012, 05:49 PM   #6
RickB
Senior Member
 
Join Date: March 1, 2000
Location: Boise, ID
Posts: 8,511
The original .357 Mag load was a 158gr bullet at 1500fps, from an 8.75" barrel; a barrel shorter than that will not allow the cartridge to reach its full potential.
RickB is offline  
Old October 10, 2012, 05:55 PM   #7
Mello2u
Senior Member
 
Join Date: February 21, 2009
Location: Georgia
Posts: 1,424
If you look at the graph on the link:
http://www.ballisticsbytheinch.com/calibers.html

If you average the energies of all of the loads (excluding that low Blue line) at 2", it is just under 300 ft-lbf. Then compare that to the average at 4" which is just over 600 ft-lbf. So you get a bit more than a 100% increase for going with a 4" compared to a 2".

When you compare the 4" to the 6" barrel it shows an energy of just under 800 ft-lbf, you get an increase of about 30%.

When you compare the 6" to the 8" energy figure of about 900 ft-lbf; you have an increase of about 12.5%.

Guess this is why many people "settle" for a 4" or 5" barrel as "good enough".
__________________
NRA Life Member - Orange Gunsite Member - NRA Certified Pistol Instructor
"When plunder becomes a way of life for a group of men living together in society,
they create for themselves in the course of time a legal system that authorizes it and a moral code that justifies it.
" Frederic Bastiat
Mello2u is offline  
Old October 10, 2012, 06:09 PM   #8
kraigwy
Senior Member
 
Join Date: June 16, 2008
Location: Wyoming
Posts: 11,061
Just an ideal:

I load 150 Grn LSWC with 14.5 grns of 2400 to 1328 out of my 4 in Model 28.

I run the same bullet through my Marlin '94 at a tad over 1900.

I forgot what that load does out of my 6 in Model 27 but I do know it raises heck with bowling pins.
__________________
Kraig Stuart
CPT USAR Ret
USAMU Sniper School
Distinguished Rifle Badge 1071
kraigwy is offline  
Old October 10, 2012, 06:22 PM   #9
Noreaster
Senior Member
 
Join Date: January 30, 2011
Location: New England
Posts: 1,449
Sometimes comparisons will show newer guns with shorter barrels having similar or better velocity then an older gun with a longer barrel, (Buffalo bore chart.) But generally you need a six inch barrel, at least, for complete powder burn.

For hunting I've always thought a Contender in 357 mag and a 12inch barrel is a totally different gun then revolvers with 6 & 8 inch pipes.
Noreaster is offline  
Old October 10, 2012, 06:28 PM   #10
siska
Junior member
 
Join Date: October 10, 2012
Posts: 13
somebody's dreaming. 600 ft lbs in a 4" 357?

not happening. 500 ft lbs, yes, 600, no. Not with standard factory loads, and certainly not with anything that is even remotely like fast enough for combat repeat hits.
siska is offline  
Old October 10, 2012, 07:14 PM   #11
Isk
Senior Member
 
Join Date: June 28, 2011
Location: Alaska
Posts: 206
Buffalo Bore and Double Tap both offer 158 gr. rounds that reach 600 ft. lbs. in a 4" barrel. I couldn't tell you if either allows for quick follow ups...but nobody is "dreaming".
__________________
The possession of arms is the distinction between a freeman and a slave. -James Burgh
Isk is offline  
Old October 10, 2012, 07:45 PM   #12
kraigwy
Senior Member
 
Join Date: June 16, 2008
Location: Wyoming
Posts: 11,061
Quote:
not happening. 500 ft lbs, yes, 600, no.
Why?

It's not that difficult to get 600 ft lbs out of a 4 inch M-28. As I said I use 150 grns @1328 FPS. That's not a hot load but its 588 ft lbs. If I was to use 158s at the same velocity (doable) it would be 619 ft lbs.
__________________
Kraig Stuart
CPT USAR Ret
USAMU Sniper School
Distinguished Rifle Badge 1071
kraigwy is offline  
Old October 10, 2012, 08:05 PM   #13
Bob Wright
Senior Member
 
Join Date: July 10, 2012
Location: Memphis, Tennessee
Posts: 2,986
The advantage to handloading ammunition is to match powder to barrel length, more or less.

Some powders, such as Bullseye, Winchester 231, and Hodgdon's HP-38 deliver pretty respectable velocities fired from the cylinder, no barrel.

Very fast burning powders work well with short barrels, while the slow burning powders work their best with barrels running in excess of 4".

Bob Wright
Bob Wright is offline  
Old October 10, 2012, 08:30 PM   #14
oldgranpa
Senior Member
 
Join Date: June 5, 2006
Location: Alabama
Posts: 209
for medium game, my 6 1/2" barrel Blackhawk .357 get almost 1500fps with Federal Eagle, fair recoil. No where that much with my 2" snub and recoil is awful.
oldgranpa is offline  
Old October 10, 2012, 10:21 PM   #15
RalphS
Senior Member
 
Join Date: December 24, 2010
Posts: 111
Quote:
not happening. 500 ft lbs, yes, 600, no.
600 ft lbs is easy with a Ruger. My 4 inch GP100 shoots a 185 grain Beartooth bullet at 1293 fps with my handloads.

That's 686 ft lbs.
RalphS is offline  
Old October 10, 2012, 11:27 PM   #16
AZAK
Senior Member
 
Join Date: May 15, 2008
Location: the object towards which the action of the sea is directed
Posts: 2,123
siska
Quote:
not happening. 500 ft lbs, yes, 600, no. Not with standard factory loads,

How about 800 territory with factory ammo.

Buffalo Bore Heavy 180 @ 1450 out of my Ruger Security Six with 6 inch barrel.
https://www.buffalobore.com/index.ph...t_detail&p=100
__________________
The lowest paid college major/degree in this country after graduation...
Elementary Education.

Now, go figure...
AZAK is offline  
Old October 10, 2012, 11:30 PM   #17
skidder
Senior Member
 
Join Date: August 17, 2008
Location: Montana
Posts: 640
the link posted above is not from a revolver. The revolver info is under the cylinder gap section.

With a cylinder gap of .006 you can see the velocity dies down much faster due to the escaping gasses. You gain about 200 fps from 2" to 6" barrel, and about the same from 6" to 18". the ratio of barrel length to velocity narrows considerably because the longer the bullet is in the barrel the more gasses can escape through the cylinder gap. You don't get that big increase like would from a Thomson or Marlin.

Cylinder Gap Test
__________________
Gun permit?? A bread crumb tossed to a sleeping society awoken by the sound of complacency. "They are for your own good", and "you will understand when you see all the lives they save". Yes master, what else will you toss me from your bag of infringements?? Do you want me to roll over and play dead? I do that very well. --skidder
skidder is offline  
Old October 10, 2012, 11:44 PM   #18
AZAK
Senior Member
 
Join Date: May 15, 2008
Location: the object towards which the action of the sea is directed
Posts: 2,123
Quote:
the link posted above is not from a revolver
I am assuming that you are referring to the Ballistics by the inch quite a bit up the page; not the Buffalo Bore link directly above your post.

I can assure you that the numbers which I posted are still on my chronograph.
__________________
The lowest paid college major/degree in this country after graduation...
Elementary Education.

Now, go figure...
AZAK is offline  
Old October 11, 2012, 04:08 AM   #19
old bear
Senior Member
 
Join Date: November 3, 2009
Location: Not close enough to the beach
Posts: 1,477
As a general rule of thumb, for revolvers, you will loose 50 FPS for every inch the barrel is shortened. Therefore if a 1,000 FPS is still the Minimum standard for bullet expansion you would want a round that is traveling at least 1,200 FPS from a 6" barrel.
old bear is offline  
Old October 11, 2012, 09:17 AM   #20
Madcap_Magician
Senior Member
 
Join Date: August 13, 2009
Location: MN
Posts: 668
The wide variation of .357 Magnum loads and the effect of cylinder gap kind of makes it impossible to state definitively.

I think the velocity gain from adding barrel length peaks for most loads around 4" to 6". That is, you gain a lot of velocity from barrels up to that length, but after that length the gain is much smaller, to the point that if you have a 20" rifle, you're probably not gaining more than 5 fps or so and may actually be losing velocity over a 16" or 18" carbine.

Other loads are optimized for short-barrel snubnose revolvers.

My personal preference is 3", which is a compromise between the full effectiveness of 4" barrels and the size of the 2", while retaining most of the velocity gains from the longer barrel and minimizing the muzzle flash and flip of the snubnose.
Madcap_Magician is offline  
Old October 11, 2012, 09:34 AM   #21
skidder
Senior Member
 
Join Date: August 17, 2008
Location: Montana
Posts: 640
Quote:
I am assuming that you are referring to the Ballistics by the inch quite a bit up the page; not the Buffalo Bore link directly above your post
Yes.
__________________
Gun permit?? A bread crumb tossed to a sleeping society awoken by the sound of complacency. "They are for your own good", and "you will understand when you see all the lives they save". Yes master, what else will you toss me from your bag of infringements?? Do you want me to roll over and play dead? I do that very well. --skidder
skidder is offline  
Old October 11, 2012, 12:36 PM   #22
Nanuk
Senior Member
 
Join Date: January 2, 2005
Location: Where the deer and the antelope roam.
Posts: 3,082
Quote:
not happening. 500 ft lbs, yes, 600, no. Not with standard factory loads, and certainly not with anything that is even remotely like fast enough for combat repeat hits.
That totally depends or your definition of fast enough and the shooters skill level.
__________________
Retired Law Enforcement
U. S. Army Veteran
Armorer
My rifle and pistol are tools, I am the weapon.
Nanuk is offline  
Old October 11, 2012, 01:12 PM   #23
kraigwy
Senior Member
 
Join Date: June 16, 2008
Location: Wyoming
Posts: 11,061
Quote:
not happening. 500 ft lbs, yes, 600, no. Not with standard factory loads, and certainly not with anything that is even remotely like fast enough for combat repeat hits.
Guess you never seen anyone shoot full load magnums in a bowlin pin match. That can indeed get fast hits, as fast as it takes to move from one pin to another, pins being 16 inches a part.
__________________
Kraig Stuart
CPT USAR Ret
USAMU Sniper School
Distinguished Rifle Badge 1071
kraigwy is offline  
Old October 11, 2012, 02:18 PM   #24
Sevens
Senior Member
 
Join Date: July 28, 2007
Location: Ohio
Posts: 11,755
Chrongraphed AVERAGE of 723 ft-lbs in my .357 Magnum, 10-shot average.

That's a 158 grain Zero JSP pushed to 1,436 FPS average. (1,487 FPS peak)
__________________
Attention Brass rats and other reloaders: I really need .327 Federal Magnum brass, no lot size too small. Tell me what caliber you need and I'll see what I have to swap. PM me and we'll discuss.
Sevens is offline  
Old October 11, 2012, 02:19 PM   #25
Sevens
Senior Member
 
Join Date: July 28, 2007
Location: Ohio
Posts: 11,755
OOPS! Sorry people...that's from my Coonan.

I'll have to try that one in one of my beater revolvers.
__________________
Attention Brass rats and other reloaders: I really need .327 Federal Magnum brass, no lot size too small. Tell me what caliber you need and I'll see what I have to swap. PM me and we'll discuss.
Sevens is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:34 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.10770 seconds with 10 queries