The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Revolver Forum

Reply
 
Thread Tools Search this Thread
Old April 10, 2009, 09:51 AM   #1326
Utah
Junior Member
 
Join Date: April 10, 2009
Posts: 3
Several older revolvers need their DOB...

The first is a S&W Model 3, with serial number #102xxx in .32. Next is a more recent S&W 27-2 in .357 Mag., serial number #108xxx.

Any and all input greatly appreciated.

You can find pictures below.

Last edited by Glenn E. Meyer; November 30, 2013 at 11:47 AM.
Utah is offline  
Old April 10, 2009, 07:52 PM   #1327
Radagast
Senior Member
 
Join Date: July 13, 2001
Posts: 449
Utah: The .32 is a .32 Double Action 4th Model, manufactured in the serial number range 43406 to 282999 between 1883 & 1909. Guns made before serial number 209301 are classified as antiques by the BATF. Your gun was made to shoot blackpowder loads and will have a shortened lifespan if fired with modern smokeless powders.

Per the standard catalog of S&W, value in 2006 would have been around $150 to $200.

The other gun appears to be a modern copy of the Remington Derringer.
Radagast is offline  
Old April 11, 2009, 10:12 AM   #1328
Utah
Junior Member
 
Join Date: April 10, 2009
Posts: 3
Thanks much...

Can someone provide a manufacture date on the S&W 27-2 in .357 Mag., serial number #108xxx?

Any and all input greatly appreciated.

Mike
Utah is offline  
Old April 11, 2009, 10:38 AM   #1329
Radagast
Senior Member
 
Join Date: July 13, 2001
Posts: 449
Utah, sorry, I didn't open the second photo. The S&W model 27-2 was introduced in 1961 and continued in production until 1982. The serial number should have an S or an N prefix. If the serial number is N108xxx then it was manufactured in 1973.
If there is no S or N in front of the number you are quoting then it is not the serial number, you will need to remove the grips, the correct serial number is on the bottom of the grip frame. Other numbers stamped on the gun would be assembly numbers to help track fitted parts through the factory.

In excellent condition the Standard Catalog of S&W gave a value of $500 in 2006. Yours appears to be the 3.5 inch barrel, which would command a slight premium. Values may have risen since then, check out the online auction sites such as Gunbroker to get a better feel for value. T
Radagast is offline  
Old April 11, 2009, 12:47 PM   #1330
txstang84
Senior Member
 
Join Date: April 11, 2009
Location: The Lone Star State
Posts: 636
Can someone help a newb out?

Hi all, I'm new The Firing Line, but have always been interested in firearms of all kinds. I recently acquired a S&W Model 39-2, and I've been trying to gather up as much info as I can on it-can someone tell me an approximate mfr date for this serial number?

Serial number A120xxx

Any assistance is greatly appreciated!
txstang84 is offline  
Old April 11, 2009, 08:54 PM   #1331
Radagast
Senior Member
 
Join Date: July 13, 2001
Posts: 449
txstang84: Your 39-2 was manufactured in 1971 in the serial number range A115001 to A156801. The 39-2 was introduced in 1971 and has an alloy frame and a steel slide. Model 39s made prior to this had a steel frame. The model 39 was produced from 1954-1982. It was effectively replaced by the model 539 & 639 'second generation' S&W automatics.
Radagast is offline  
Old April 12, 2009, 08:22 AM   #1332
txstang84
Senior Member
 
Join Date: April 11, 2009
Location: The Lone Star State
Posts: 636
Thanks!

Thank you very much Sir! I'm sure I'll enjoy it as soon as I return from this deployment.
txstang84 is offline  
Old April 12, 2009, 04:34 PM   #1333
jlwman
Senior Member
 
Join Date: January 23, 2006
Location: Kansas
Posts: 202
How about a Model 43 with a serial number of M386XX.

Thanks!

BTW...anyone know what a near mint condition matching box would be worth? No papers...just the box.
jlwman is offline  
Old April 12, 2009, 07:56 PM   #1334
Radagast
Senior Member
 
Join Date: July 13, 2001
Posts: 449
jlwman: Following info taken from the Standard Catalog of S&W. Prices are from 2006. Offering it at at www.smith-wessonforum.com may get you a higher offer from a collector who needs one to fill a hole in his accumulation.

The model 43 was also known as the 1955 .22/32 Kit Gun Airweight. J frame alloy target frame. Aluminum cylinder. square butt, round butt very rare. 3.5 inch barrel, 2 inch barrel is rare. Blue or Nickel finish, Nickel finish is very scarce. Walnut diamond Magna grips. Flat thumb latch prior to 1966, Small S&W trademark on the frame, not marked Airweight. Produced 1954-1974. Your gun falls in the serial number range for 1971-1973, being M30001 to M60000. In ANIB condition: $425. Excellent condition:$325.00

A 22 magnum chambered gun has been reported but not verified.
Radagast is offline  
Old April 12, 2009, 08:14 PM   #1335
hoytinak
Senior Member
 
Join Date: July 5, 2006
Location: Texas
Posts: 5,721
Anyone got a manufactering date/value on a 98% Model 10-6 serial #D560023? Thanks

Last edited by hoytinak; April 12, 2009 at 08:20 PM.
hoytinak is offline  
Old April 12, 2009, 11:19 PM   #1336
Radagast
Senior Member
 
Join Date: July 13, 2001
Posts: 449
hoytinak: 1973-1974. Serial number range fro those years was D510001 - D659901.
Radagast is offline  
Old April 12, 2009, 11:30 PM   #1337
DixieFlatline
Junior Member
 
Join Date: April 12, 2009
Posts: 8
Little Help...

I was hoping someone could help me find the manufacture date for a S&W Model 36, serial number 717XXX. I'm carrying it as a backup and wanted to make sure it would stand up to some proper +P defensive loads. Any help would be appreciated.
DixieFlatline is offline  
Old April 13, 2009, 08:06 AM   #1338
carguychris
Senior Member
 
Join Date: October 20, 2007
Location: Richardson, TX
Posts: 7,523
Quote:
I was hoping someone could help me find the manufacture date for a S&W Model 36, serial number 717XXX. I'm carrying it as a backup and wanted to make sure it would stand up to some proper +P defensive loads.
1968-1969. Regarding +P, an older all-steel J frame like your Model 36 can handle limited amounts of +P ammo just fine. It may shoot loose if fed a steady diet, but it's a premature wear issue, not a gun-destroying kB! issue.

OTOH older alloy-frame Airweights should only be fed standard-pressure ammo because the frames are known to crack or stretch, and many written sources recommend against ever firing an early alloy-cylinder Airweight.
carguychris is offline  
Old April 13, 2009, 09:31 AM   #1339
Rocked
Senior Member
 
Join Date: September 26, 2006
Location: North Florida
Posts: 152
Can anybody help me out with an old k frame?

Serial is 865XX. Its a blued 3" marked .38 S&W.

Thanks guys.
Rocked is offline  
Old April 13, 2009, 09:49 AM   #1340
Radagast
Senior Member
 
Join Date: July 13, 2001
Posts: 449
Rocked: You have a S&W K200 British Service Revolver, built between 1940 & 1942 for the British government. The barrel would have been 5 inches long originally and the caliber .38 S&W (The British used a 200 grain bullet in the .38 S&W case as their service round).
Your gun may have been bored out at some point to accommodate .38 Special cartridges. If it has only use standard pressure rounds in the gun as the chamber near the rim will be over sized.
Radagast is offline  
Old April 13, 2009, 02:10 PM   #1341
protwin
Junior Member
 
Join Date: April 13, 2009
Posts: 3
need help on age and value

--------------------------------------------------------------------------------

I have two model 57 41 mags. I am wondering the age of the guns, if any one can help please let me know. this gun is new never fired 100% mod 57 N77501 4 then 82844, the second gun is 98% shot a box through it mod 57-1 Ajj65545 316 x6xx3
protwin is offline  
Old April 13, 2009, 02:13 PM   #1342
protwin
Junior Member
 
Join Date: April 13, 2009
Posts: 3
pictures for ref

--------------------------------------------------------------------------------

I have two model 57 41 mags. I am wondering the age of the guns, if any one can help please let me know. mod 57 N77501 4 then 82844, the second gun mod 57-1 Ajj65545 316 x6xx3

Last edited by Glenn E. Meyer; November 30, 2013 at 11:47 AM.
protwin is offline  
Old April 13, 2009, 02:55 PM   #1343
DixieFlatline
Junior Member
 
Join Date: April 12, 2009
Posts: 8
Chris, thanks a bunch for the info. I'm convinced that little snubby is a solid, dependable gun, and I didn't want to do anything unhealthy to it.
DixieFlatline is offline  
Old April 13, 2009, 03:04 PM   #1344
Jonathank1982
Member
 
Join Date: September 16, 2008
Location: Western NY
Posts: 20
S&W Age

Model 13-1
4in barrel square grips
.357
Ser# D938xxx


Thanks!!

Jonathan
Jonathank1982 is offline  
Old April 13, 2009, 10:27 PM   #1345
carguychris
Senior Member
 
Join Date: October 20, 2007
Location: Richardson, TX
Posts: 7,523
Quote:
model 13-1
4in Barrel Square Grips
.357
Ser# D938xxx
1976-1977.
carguychris is offline  
Old April 14, 2009, 09:01 AM   #1346
Radagast
Senior Member
 
Join Date: July 13, 2001
Posts: 449
protwin: Your model 57 serial number N77501 dates to 1980.

The 57-1 was manufactured between 1982 & 1988. The serial number prefix AJJ should have been used between July 1985 & November 1985. the serial number should only have four digiets though: AJJxxxx.

The serial number is sometimes stamped under the crane with the model number, there are often 'assembly' or parts numbers to confuse things. The Serial number is always stamped on the bottom of the grip frame, you will need to remove the grips to see this. If it is different to AJJxxxxx get back to us and one of us will look it up for you.
Radagast is offline  
Old April 14, 2009, 10:10 AM   #1347
carguychris
Senior Member
 
Join Date: October 20, 2007
Location: Richardson, TX
Posts: 7,523
Quote:
The model 43 was also known as the 1955 .22/32 Kit Gun Airweight. J frame alloy target frame... Your gun falls in the serial number range for 1971-1973, being M30001 to M60000. In ANIB condition: $425. Excellent condition:$325.00
IMHO those values are about $150-$175 low in today's market. Postwar .22LR J frames have climbed sharply in value over the last 2 years.
Quote:
BTW...anyone know what a near mint condition matching {Model 43} box would be worth? No papers...just the box.
$50-$80, tending towards the higher end because the Model 43 is somewhat scarce.
carguychris is offline  
Old April 14, 2009, 02:31 PM   #1348
greg170
Junior Member
 
Join Date: April 14, 2009
Posts: 1
Model 36 serial number help

I was hoping someone could help me with the date on a model 36 S&W I bought from an old police officer. He said he carried it as a backup and off duty weapon for many years and couldn't tell me exactly how old it is. Hopefully someone here can help me out.

The serial number is 212XXX

Thanks!
greg170 is offline  
Old April 14, 2009, 05:04 PM   #1349
polkey
Junior Member
 
Join Date: October 25, 2008
Posts: 6
S&W 44 russian DA revolver
6" barrel
Serial # 282xx
?
polkey is offline  
Old April 14, 2009, 05:31 PM   #1350
Radagast
Senior Member
 
Join Date: July 13, 2001
Posts: 449
Greg 170: Between 1957 & 1962, serial number range for this period was 125000 to 295000.
Radagast is offline  
Reply

Tags
s&w 686

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:43 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2024 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.55203 seconds with 9 queries