The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools Search this Thread
Old December 3, 2009, 05:58 PM   #1
remguy
Junior Member
 
Join Date: November 17, 2009
Posts: 1
varget and cci primers

anybody know anything about getting better groupes using cci primes with varget i mean better than fed or other brands.
remguy is offline  
Old December 3, 2009, 08:57 PM   #2
wncchester
Senior Member
 
Join Date: December 1, 2002
Posts: 2,832
I doubt many folks would claim any average difference without trying them.
wncchester is offline  
Old December 3, 2009, 09:40 PM   #3
Crusty Deary Ol'Coot
Senior Member
 
Join Date: November 19, 2009
Location: Deary, Ideeeeeeho
Posts: 531
Testing, testing, testing testing, kind of like with a .22 and finding which of the many rimfire rounds your rifle likes, running test with your firearm etc. will tell the story as to which does the best for you.

However, that information will only be valid providing you buy components in as large a quanity as you can. Primers by the thousand, powder AND BRASS of the same lot number etc.

The change of just one item in your components can change the total picture, which brings us to the fact that while doing your test, NEVER change more then one component at a time.

To do so and then seeing changes for the better or worse in your results, will leave you wondering what happened and where to go next.

Consistancy is the way to quality reloads.

Keep em coming!

Crusty Deary Ol'Coot

Last edited by Crusty Deary Ol'Coot; December 3, 2009 at 09:42 PM. Reason: spelling
Crusty Deary Ol'Coot is offline  
Old December 3, 2009, 09:56 PM   #4
Slamfire
Senior Member
 
Join Date: May 27, 2007
Posts: 5,261
One Long Range Champion I know uses CCI Benchrest primers.

I don't know how good of a shot you are. If you are one of the top five shooters in the US, then I would believe that you are indeed seeing accuracy variations due to primers.

I suspect that you are not one of the top five shooters in the US. Maybe not even in the top 200 shooters of the US.

If so, maybe what you are seeing are variations due to sight alignment, trigger pull, and position.

I know I have seen this. I have found an exceptional load during load testing, shoot the stuff in a match and I do horrible, back to the bench, load shoots great. Back to the match and the load shoots great.

It was never the load. It was me.
Slamfire is offline  
Old December 3, 2009, 09:56 PM   #5
Shoney
Senior Member
 
Join Date: February 21, 2002
Location: Transplanted from Montana
Posts: 2,311
Primers can make a lot of difference in accuracy, but you must have a weapon capable of shooting great groups; you must have the optics to see well for shot placment; and finally you must have the ability to shoot accurately.

Without all three of the above, you proably will not be able to tell the difference.
__________________
I pledge allegiance to the Flag - - -, and to the Republic for which it stands….Our Forefathers were brilliant for giving us a Republic, not a democracy! Do you know the difference??? and WHY?http://www.wallbuilders.com/LIBissue...les.asp?id=111
Shoney is offline  
Old December 3, 2009, 10:05 PM   #6
L Puckett
Senior Member
 
Join Date: March 2, 2002
Location: Mid-Tennessee
Posts: 150
Yes, I have "heard" it mentioned/debated a couple of times. The groups being discussed were all shot at 1000 yrds. The arguement was that the CCI BR-2's had less vertical dispersion.

Obviously, the claim was that the ammunition had a better ES/SD with the CCI's.

I personally have not done any experimenting.....using FED 210M's my ES/SD's are all single digits anyway, but that can be due to several other contributing factors, hint.....neck tension.

LP
__________________
A Good Day is going shooting..........A Great Day is dry ground and no wind - Me
L Puckett is offline  
Old December 4, 2009, 02:36 AM   #7
Tex S
Senior Member
 
Join Date: November 12, 2008
Location: Fort Worth, TEXAS
Posts: 875
Quote:
hint.....neck tension.
Care to elaborate? Are you neck turning and using bushing dies?
Tex S is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:49 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.05044 seconds with 10 queries