The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools Search this Thread
Old December 2, 2009, 04:41 AM   #1
Plaz
Senior Member
 
Join Date: December 23, 2007
Posts: 131
crimping 9MM

Should I use a taper crimp die when loading 9MM on my Hornady LNL?
Plaz is offline  
Old December 2, 2009, 07:30 AM   #2
drail
Junior member
 
Join Date: February 2, 2008
Posts: 3,150
Yes. But almost all dies for 9mm will be a taper crimp. Just crimp enough to remove the flaring from the expander/flaring die. Hold the round up to a good light source and sight down the side of the case. You will be able to see the flare. If you have rounds setting back from chambering measure the expander button in your expander die . It needs to be 3 or 4 thous. smaller than the bullet dia. Using heavy crimps will not stop bullet setback. The case needs to have a tight grip on the bullet BEFORE you apply a crimp. On semi auto rounds only crimp enough to remove the flaring.
drail is offline  
Old December 2, 2009, 02:44 PM   #3
Shoney
Senior Member
 
Join Date: February 21, 2002
Location: Transplanted from Montana
Posts: 2,311
Yes, you need to use a taper crimp die for 9mm.

Hornady puts out all their standard dies in roll crimp, even the cases known to need taper crimp. From an inventory point of view, that makes good sense, but from a reloading point of view it is beyond my comprehension and a poor move on their part.

Look on the die box to see what it says. If it does not specifically say TAPER CRIMP, then it is a roll crimp die.


Hornady only offers 8 taper crimp dies that come singly, not in sets, and they do not have a seating stem. If you will look on Horndy's web site, the specific dies will be named.
__________________
I pledge allegiance to the Flag - - -, and to the Republic for which it stands….Our Forefathers were brilliant for giving us a Republic, not a democracy! Do you know the difference??? and WHY?http://www.wallbuilders.com/LIBissue...les.asp?id=111
Shoney is offline  
Old December 2, 2009, 03:19 PM   #4
Plaz
Senior Member
 
Join Date: December 23, 2007
Posts: 131
The hornady video of reloading 9MM doesn't show use of a taper crimp die. Doesn't this conflict with requirement for usage of taper crimp die? Which configuration is better?

Copy and paste this link onto google to get the Hornady procedure without using a taper crimp die.

Hornady LNL-AP 9mm part I (HD)
Plaz is offline  
Old December 2, 2009, 04:43 PM   #5
bozhoz
Member
 
Join Date: March 15, 2009
Posts: 82
I use the Hornady Dimension Dies in 9mm. I thought it was a taper crimp in the die, but I could be wrong. At any rate, I hardly use any flare at all when flaring the cases. Enough only to just barely have the bullet start. Then, I roll over the case with a light crimp, just enought to remove any flaring. I've fired about 250 through my Glock without any issue.
bozhoz is offline  
Old December 3, 2009, 10:41 PM   #6
jpsshack
Senior Member
 
Join Date: October 18, 2008
Location: Northern New England
Posts: 169
I recommend adding the crimp as a separate stage, after seating the bullets.
jpsshack is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:44 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06454 seconds with 10 queries