June 25, 2020, 12:30 AM | #1 |
Senior Member
Join Date: March 20, 2011
Location: Willamina, OR
Posts: 1,908
|
Choke tube removal
As I talked about in the shotgun forum here, I have a new Savage 320 barrel. I'd like to remove the choke tube and lube with anti-seize compound and reinstall it before I shoot any rounds though it...
Anyway what I know is that the Savage 320 shotgun is a Chinese copy of the Winchester 1300. What I'd like to know and I haven't been able to find out searching on the net, is will it use the same choke tubes and removal tool as Winchester chokes. Anybody here have any experience with this? Tony |
June 25, 2020, 12:41 AM | #2 |
Senior Member
Join Date: March 20, 2011
Location: Willamina, OR
Posts: 1,908
|
Never mind. I got it out and you're going to think I'm nuts with how I did it. I picked up a quarter off my office floor and it kinda looked like the right size. I held it in my Leatherman tool and the choke tube turned right out.
I should have thought of that sooner... Tony |
June 25, 2020, 08:58 AM | #3 |
Senior Member
Join Date: December 6, 2014
Posts: 6,446
|
Quarters are decent, but they typically do not seat in the notches completely. Anti-seize works, as does grease (like RIG or Shooter's Choice, as does even a light coating of oil. Just remember when you clean your gun to remove and clean the threads of the choke tube AND the threads in the barrel.
__________________
"I believe that people have a right to decide their own destinies; people own themselves. I also believe that, in a democracy, government exists because (and only so long as) individual citizens give it a 'temporary license to exist'—in exchange for a promise that it will behave itself. In a democracy, you own the government—it doesn't own you."- Frank Zappa |
June 26, 2020, 09:27 AM | #4 |
Staff
Join Date: March 4, 2005
Location: Ohio
Posts: 21,063
|
Years ago I was at the front desk in a Bearings Inc. location and noticed the full line of Bostik Never-Seez products in a display rack at the time. I read the labels and wound up picking up a can of their nickel-based product rated for nuclear reactor stainless steam fittings. I got it because it guarantees to prevent galling between plain to stainless or stainless to stainless fittings, and stainless barrels on carbon steel receivers are common to put together. It cost more than the standard copper-based product, but man does that stuff work a treat. Spec sheet here.
__________________
Gunsite Orange Hat Family Member CMP Certified GSM Master Instructor NRA Certified Rifle Instructor NRA Benefactor Member and Golden Eagle |
June 26, 2020, 10:06 AM | #5 |
Senior Member
Join Date: June 20, 2007
Location: Rainbow City, Alabama
Posts: 7,167
|
That stuff sounds good Nick. The basic anti-seize stuff I've always liked is spark-plug anti-seize from the auto parts store. Cheap and made for a dirty, high-temperature environment.
|
June 26, 2020, 10:26 AM | #6 |
Senior Member
Join Date: February 16, 2006
Location: IOWA
Posts: 8,783
|
Copper based, lets you know it's there
On M/L application, I use the copper based anti-size and have tried the nickel base and found that even though it did prevent the threads from sticking, it dried to a point where the parts were hard to un-thread. Yes, the nickle based, has a higher temp. rating. I always carry the spark-plug crayon in the field and it works very well one advantage to the copper based is the color. No guessing whether or not, it has been applied. For most choke tubes, I use BC anti-size that come in a squeeze tube. I've seen where some folks don't feel they need any and later, regret it. ……
Be Safe !!!
__________________
'Fundamental truths' are easy to recognize because they are verified daily through simple observation and thus, require no testing. |
June 26, 2020, 11:23 AM | #7 |
Senior Member
Join Date: March 2, 2017
Posts: 1,868
|
Well got aa new CZ Bobwhite few weeks ago and it's the first gun I ever even shot that has tubes of any kind in the barrel. In those short few weeks I've found the easiest way to deal with choke tubes is don't get them! Took mine out just to say I did but probably put it something like IC/Mod and never take them out again! Real turn off for me looking at those barrels with a lump in them where the choke goes. Not any bigger on those extended chokes either. Imagine a brand new Purdy SxS with extended chokes! WOW!
|
June 27, 2020, 01:22 PM | #8 | |
Staff
Join Date: March 11, 2006
Location: Upper US
Posts: 28,836
|
Quote:
One of the things to be aware of is that choke tubes aren't only subject to fouling holding them in, they can also get "hammer welded" in place by the pressure of firing. I don't think you need to remove and clean the threads every single time, but removing the choke tube once in a while is a good idea.
__________________
All else being equal (and it almost never is) bigger bullets tend to work better. |
|
June 27, 2020, 03:07 PM | #9 |
Senior Member
Join Date: December 6, 2014
Posts: 6,446
|
I will disagree about not cleaning them except for once in a while. Powder residue, moisture and other gunk can get in there and make them very difficult to remove. Barrels should be cleaned, and thus the choke tubes. Same for cleaning and greasing hing pins on O/Us and SxS, cleaning other wear parts and lubing, etc.
As to the swaged barrel bulge to accommodate chokes, a fixed choke barrel can have thin-wall chokes installed by Briley - no bulge.
__________________
"I believe that people have a right to decide their own destinies; people own themselves. I also believe that, in a democracy, government exists because (and only so long as) individual citizens give it a 'temporary license to exist'—in exchange for a promise that it will behave itself. In a democracy, you own the government—it doesn't own you."- Frank Zappa |
|
|