|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
November 9, 2011, 10:05 PM | #1 |
Senior Member
Join Date: November 11, 2009
Posts: 506
|
AR-15 trigger system behavior
Hi, I have a question about an AR-15 trigger: if you take off the upper, and cock the hammer by hand, then pull the trigger, let the hammer fall, and reset the hammer by hand, and you feel it engage the sear, but, you can make it fall again upon trigger reset, by just exerting a little pressure on the hammer from behind...that's not correct, right? Could that cause the rifle to fire doubles? I am guessing that no amount of pressure from behind should allow the hammer to fall until the trigger is first released and then pulled again?
|
November 9, 2011, 11:49 PM | #2 |
Senior Member
Join Date: November 6, 2010
Location: west central Illinois
Posts: 277
|
Maybe you're not truly simulating the behaviour of the FCG under normal operating conditions. Are you fully seating the hammer or are you just pulling it back until it clicks? That hammer gets slapped back hard when the bolt cycles. BTW, don't let the hammer hit the front of the lower, use a buffer of some sort.
Why are you concerned? Function problems? Doubles, slam fires, that sort of thing? Regards, Hobie |
November 10, 2011, 12:06 AM | #3 | |
Senior Member
Join Date: November 11, 2009
Posts: 506
|
Quote:
The thing is, that I can test it like this all day and the hammer will never double. But, I just discovered when taking a second look today, that if I press gently on the hammer from behind - just a little pressure is all it takes - then the releasing of the trigger will drop the hammer. Now, if I re-cock the hammer, then release the trigger, and then apply the pressure - nothing. But if the pressure is there as I release the trigger - the hammer drops. When I cock the hammer BTW I'm pushing it back as hard as I can with my fingers. I've been advised that the company I bought the trigger kit from (Del-Ton) have a reputation for poor quality trigger components. Could this be the cause of what looked like doubles? PS I am catching the hammer with my hand to prevent damage when I 'fire', thanks for the heads up. |
|
November 10, 2011, 08:13 AM | #4 |
Senior Member
Join Date: October 17, 2007
Location: Cowtown of course!
Posts: 1,747
|
If it's so easy for the hammer to move forward, then I would suggest that you have a trigger group issue and it needs to be looked at by a gunsmith.
Why? To cover yourself legally. If it is in fact a physical malfunction due to poorly produced parts, then the gun should be repaired/parts replaced. Don't take it to a public range where you don't know who is watching.
__________________
NRA Chief Range Safety Officer, Home Firearms Safety, Pistol and Rifle Instructor “Today, we need a nation of Minutemen, citizens who are not only prepared to take arms, but citizens who regard the preservation of freedom as the basic purpose of their daily life......” President John F. Kennedy |
November 10, 2011, 09:33 AM | #5 |
Senior Member
Join Date: November 11, 2009
Posts: 506
|
Yep I definitely wouldn't fire it like this - but I just wanted to check, since I still didn't know if this is a malfunction, or if they all work this way. Thanks.
|
November 10, 2011, 11:45 AM | #6 |
Senior Member
Join Date: August 7, 2000
Location: Floating down the James River in VA
Posts: 2,599
|
When you test the AR fire control components, keep your trigger finger pulled all the way back while you manually reset the hammer. It isn't the "sear" catching the hammer at that point, it's the disconnector: the little claw piece mounted in the middle of the trigger. When you release the trigger, the disconnector releases the hammer to be caught on the nose of the trigger (the closest thing the AR has to a "sear").
If sear engagement in the AR is inadequate/marginal, the AR will fire again when you release the trigger, as the disconnector will release the hammer, but the trigger nose/sear will not catch it, allowing the hammer to move forward fully, firing the weapon again. This is what often causes intermittent doubling. |
November 10, 2011, 12:21 PM | #7 |
Senior Member
Join Date: November 11, 2009
Posts: 506
|
Poodleshooter that makes sense, thanks. I have heard of this happening, but in my case, I'm just not sure if that is exactly what's happening. When I'm applying the pressure I talked about to the hammer, at that point I suppose it's still on the disconnector. Then I release the trigger, and the hammer drops. But if I don't push the hammer forwards while releasing the trigger, it will catch where it's supposed to every time. So I can't tell if that's a problem with the trigger/sear, or the disconnector, or the hammer. Anyway I am replacing the whole thing with a drop in system so that should take care of it. I'll contact the supplier of the original parts to see if they will take them back.
|
November 11, 2011, 12:03 PM | #8 |
Senior Member
Join Date: August 7, 2000
Location: Floating down the James River in VA
Posts: 2,599
|
If you can manually push the hammer off of the disconnector by simply pushing the hammer forward then either something is wrong with the disconnector hook angle (ground/worn down perhaps?)or the entire disconnector is canted backwards with respect to the trigger. This may be a disconnector spring problem. A freely moving disconnector with a missing spring might be able to release the hammer without the trigger going forward (bad).The disconnector should only release the hammer when the trigger is released. It should firmly hold the hammer while the trigger is fully pulled to the rear.
|
November 11, 2011, 12:21 PM | #9 | |||
Senior Member
Join Date: November 11, 2009
Posts: 506
|
Quote:
Quote:
Quote:
|
|||
November 11, 2011, 08:53 PM | #10 |
Senior Member
Join Date: November 11, 2009
Posts: 506
|
Just finished installing my new trigger system. I used the Timney drop in trigger. Crazy money but I had to get this sorted with the minimum hassle, so I went ahead and bought it.
The old one must have been bad because the new trigger does not exhibit the behavior I described above. Pressing the hammer from behind has no effect when I release the trigger. Not only is the new trigger far higher quality, but the safety now engages much more positively, and is much tighter. It always felt a bit rattly before. I can't see anything obviously wrong with the old components, but then I wouldn't really know what to look for. So I'll send them back to Del-Ton. Thanks for the input everyone. |
November 24, 2011, 06:47 PM | #11 |
Senior Member
Join Date: November 11, 2009
Posts: 506
|
wrapping up...
Just tested the rifle with the new trigger. I fired about 20 rounds slow fire, and then 60 fairly rapidly - no problems whatsoever. The Timney trigger is pretty good too. I have the 4lb one which is not that light but there is no creep whatsoever.
Anyway, a few days ago Del-Ton called and said they received the bad trigger parts I sent back but they couldn't reproduce the problem. So they're going to send new parts anyway. I'll probably never fit them now that I have a much higher quality trigger in there. Thanks for the help. |
|
|