|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
June 18, 2018, 01:49 PM | #1 |
Senior Member
Join Date: June 12, 2018
Location: SC, USA
Posts: 136
|
Blacking out rear sights
I've been noticing that I get distracted by the rear white "U" sight on my pistol.
I've seen a couple folks black out the rear sights and just use the front bead for quicker, cleaner sight alignment and am tempted, but hesitant. Pros and cons/ general experience with blacked out rear sights would be appreciated. Thank you for your input! |
June 18, 2018, 01:58 PM | #2 |
Staff
Join Date: March 11, 2006
Location: Upper US
Posts: 28,839
|
I blacken stainless sights with a Sharpie marker. Works tolerably well, and while it does wear, its easy to touch up.
If you're talking about a white dot/bar/ block on a dark rear sight being a distraction, you could darken it easily enough, and if you use the right stuff, it can be removed if you change your mind. I would suggest, that, if its a dot on your rear sight distracting you, you're not focusing where you should be. Don't look AT the rear sight, look through it. Easier to say than do, I admit, but its what works best, focus on the front sight, the rear sight, and the target should be a bit blurred.
__________________
All else being equal (and it almost never is) bigger bullets tend to work better. |
June 18, 2018, 02:26 PM | #3 |
Senior Member
Join Date: March 1, 2000
Location: Boise, ID
Posts: 8,518
|
I've blacked the rear dots on my two guns so equipped.
I used a Sharpie paint pen, and have not had to reapply the paint . . . but I have also not cleaned the rears sights with solvents. Can't think of a downside, unless I tried to sell the guns to someone who was a fan of 3-dot sights.
__________________
Runs off at the mouth about anything 1911 related on this site and half the time is flat out wrong. |
June 18, 2018, 03:05 PM | #4 |
Senior Member
Join Date: May 8, 2009
Location: Florida
Posts: 3,787
|
Another approach is to make the front sight more prominent. I use a night sight with a bright orange ring on the front only (HD).
|
June 19, 2018, 02:30 PM | #5 |
Senior Member
Join Date: September 13, 2005
Posts: 4,700
|
I learned to shoot a handgun Bullseye style, black sights, hence colored sights, white outlines do nothing for me. YMMV.
|
June 20, 2018, 08:59 AM | #6 |
Senior Member
Join Date: December 11, 2004
Location: Redwood City, Ca.
Posts: 4,114
|
Nothing wrong with doing that. Some may have more trouble with a U shaped sight.
tipoc
__________________
1. All guns are always loaded. 2. Never let the muzzle cover anything you are not willing to destroy. 3. Keep your finger off the trigger till you are ready to shoot. 4. Identify your target and know what is beyond it. |
June 20, 2018, 10:15 AM | #7 |
Senior Member
Join Date: June 12, 2018
Location: SC, USA
Posts: 136
|
I blacked out the back U sight and it has definitely improved my sighting.
Gun shoots point of aim and sight alignment is much quicker. I don't know what it was about that big white U but it was really throwing me off! Thanks for the help, yall. |
July 17, 2018, 05:05 PM | #8 |
Senior Member
Join Date: July 7, 2014
Location: Katy Tx
Posts: 126
|
Most 3 dot rear sights (2dot rear) can be easily modded to be all black with a small steel drill bit. Take the best fitting bit preferably from a set and with the bit in hand simply twist back and forth the bit on to the white dots and the white filled dot will begin to come off easy does it no HeMan twisting. Ive done it on Glock Taurus Springfield plastic rear sights and had good results with a f.o sight up front. Need to resale the gun just refill with white junkyard permanent marker. Not directly. Just mark up a spot on a hard surface take toothpick to the wet marker ink and touch up your rear dots again. Easy peazy.
|
July 17, 2018, 06:03 PM | #9 |
Senior Member
Join Date: April 13, 2013
Location: N. Georgia
Posts: 1,150
|
To blacken out the rear sight will void
the warranty on the gun, cause it to shoot violently left if you are a right-hander and will cause the future generation of your family to be sterile. Is that enough warning? |
July 18, 2018, 08:49 AM | #10 |
Senior Member
Join Date: April 3, 2006
Posts: 158
|
I do it pretty frequently. Depending on the gun I'll just take a marker or black nail polish and cover up the dots. This works for quick shooting but you can still usually tell the dots were there - they're just black dots instead. As such for a decent number of my guns I just went ahead and bought new sights.
Often times when replacing sights I'll go with plain black front and rear, but I also don't mind black rear with Fiber optic front. |
July 19, 2018, 05:04 PM | #11 |
Junior member
Join Date: March 9, 2018
Location: NY
Posts: 90
|
I don't do it, and can't figured out why you would. Thunder, you must know something I don't! Please tell me why you would do such a thing? For me that's how I was trained in the military and LE. They are a big part of my sight picture.
|
Tags |
aiming , blacked out , rear sight , sights |
|
|