July 6, 2012, 08:26 AM | #1 |
Senior Member
Join Date: January 10, 2012
Posts: 3,881
|
H335, varget or ?
what is a good powder other than H335 or Varget for the 223 ar-15 with a 16" barrel ?
|
July 6, 2012, 08:51 AM | #2 |
Senior Member
Join Date: June 4, 2006
Location: West Virginia
Posts: 2,258
|
I have used H-335, Varget, BL(C)2 and W-748. They all work but I like H-335 best.
__________________
I don't ever remember being absent minded. |
July 6, 2012, 08:53 AM | #3 |
Senior Member
Join Date: January 27, 2010
Location: Norfolk, VA
Posts: 2,905
|
I've liked H335 the best so far as well. But, I was given eight pounds of AA2230, and I'm almost out of H335, so I'm hoping I like the 2230 too.
|
July 6, 2012, 09:05 AM | #4 |
Senior Member
Join Date: November 14, 2011
Posts: 524
|
I have some but have yet to try it but IMR 8208 XBR is suppose to be a good option. H335 for plinking and Varget for heavier match bullet is what I have been working on with good results
|
July 6, 2012, 09:06 AM | #5 |
Member
Join Date: April 4, 2011
Location: Monett, Missouri
Posts: 98
|
335 & Varget
The only powder I would suggest other than the ones you mentioned would be Benchmark. It is very good in 223 for the 50 and 55 grain bullets I have worked with.
Are you set on a certain bullet? |
July 6, 2012, 09:10 AM | #6 |
Senior Member
Join Date: September 6, 2011
Location: Wyoming
Posts: 1,350
|
I have done some testing with CFE223. Here is a link to my post on TFL showing velocities at different loads of CFE223 and standard vs. magnum primers. http://thefiringline.com/forums/show...ghlight=cfe223
The CFE223 really did keep the copper fouling to a minimum. After fireing the rounds for this test, I cleaned my bore with Barnes copper remover and only needed one patch. Normally it takes four or five wet patches and some heavy scrubbing to to get the copper out of my barrel! I didn't have a good day for accuracy, but I am going to work some loads with CFE223 if it ever cools off! 90+ degrees around here makes it hard to sit at the range!
__________________
Go Pokes! Go Rams! Last edited by Wyoredman; July 6, 2012 at 09:31 AM. Reason: Spelling correctios |
July 6, 2012, 09:34 AM | #7 |
Senior Member
Join Date: July 3, 2008
Location: middle GA
Posts: 326
|
I'd give H322, and IMR-4198 a try.
__________________
Jan. 4, 2007 gasoline $2.10 gal....HMMM? |
July 6, 2012, 09:53 AM | #8 |
Senior Member
Join Date: January 6, 2011
Location: Thornton, Texas
Posts: 3,997
|
I use H335 for the 40 grainers and AA2230 for the 65 grainers. I use near max loads of each. I was going to try the 2230 on the smaller bullet, but the H335 shot so well I just went with it.
|
July 6, 2012, 11:02 AM | #9 |
Senior Member
Join Date: February 11, 2011
Location: Central Florida
Posts: 378
|
My sons AR does well with Benchmark and CFE223 / he shooting 69 gr Sierras in it. He can put 10 shoots in 1.5" which is good if you consider the barrel lenght and trigger pull (which is really heavy).
|
July 6, 2012, 11:14 AM | #10 |
Senior Member
Join Date: January 10, 2012
Posts: 3,881
|
I am mainly loading 55 gr Hornady bullets.
Thanks for all the replies |
July 6, 2012, 11:28 AM | #11 |
Senior Member
Join Date: November 19, 2002
Location: Mississippi
Posts: 963
|
I sometimes get all nostalgic, IMR-3031 and H-380
|
July 6, 2012, 04:25 PM | #12 |
Senior Member
Join Date: September 17, 2006
Posts: 105
|
H335, H4198, Varget, I use them all in my AR loads, depends on the bullet I use as to which powered works best.
|
July 6, 2012, 04:52 PM | #13 |
Senior Member
Join Date: December 24, 2010
Location: Central Louisiana
Posts: 3,137
|
Or IMR 4895, or Reloder 15. Both work great in the AR15.
|
July 6, 2012, 08:53 PM | #14 | |
Senior Member
Join Date: January 10, 2012
Posts: 3,881
|
Quote:
|
|
July 6, 2012, 09:06 PM | #15 |
Senior Member
Join Date: December 20, 2007
Location: S.E. Minnesota
Posts: 4,720
|
How about H322?
I'm still using Varget. Gonna switch to WC844 for my 55-grain loads next time I do a batch, and keep using Varget for the 62's until I use it up. CFE233 and SMP842 look intriguing, but I couldn't find any in stock anywhere so I bought 2 jugs of 844 instead. That will last me a long time.
__________________
"Everything they do is so dramatic and flamboyant. It just makes me want to set myself on fire!" —Lucille Bluth |
July 7, 2012, 07:46 AM | #16 | |
Senior Member
Join Date: September 17, 2006
Posts: 105
|
Quote:
|
|
July 7, 2012, 08:17 AM | #17 | ||
Senior Member
Join Date: June 4, 2006
Location: West Virginia
Posts: 2,258
|
Quote:
Quote:
__________________
I don't ever remember being absent minded. |
||
July 7, 2012, 12:06 PM | #18 | |
Senior Member
Join Date: January 10, 2012
Posts: 3,881
|
Quote:
How many grains of H335 ? I have been getting good results using 24.0 gr with the 55 gr dogtowns and 24.5 with Hornady 55 gr fmjbt's |
|
July 7, 2012, 04:41 PM | #19 |
Senior Member
Join Date: April 4, 2011
Location: LA (Greater Los Angeles Area)
Posts: 2,598
|
Military 844
I have both H335 and military surplus 844. They are said to use the same data: this means starting loads listed for 335 are starting loads for 844.
But I have found 844 to burn a little slower, and load more powder. In other words I think 335 is hotter for the same measure, and would not use the same amount as 844; definitely less by volume. I did work up to max 844 M193 load of 28.5 grns 55 gr fmj with no signs of excess pressure. But shooting those all day got my barrel very hot. TM-43-0001-27 Propllant: Type-----. WC844 or CMR 170 Weight - 28.5 or 26.5 gr Projectile: Weight 56 gr Performance: Chamber pressure 52,000 psi Velocity 3250 fps, 15 ft from muzzle
__________________
............ Last edited by Marco Califo; July 7, 2012 at 11:44 PM. Reason: Yes. |
July 7, 2012, 06:02 PM | #20 |
Staff
Join Date: March 4, 2005
Location: Ohio
Posts: 21,060
|
Marco,
That's normal. The reverse could just as easily be true on your next purchase. Surplus WC844 will have been purchased in bulk. Bulk purchases are not blended to a standard burn rate the way canister grade stuff sold to handloaders is. The expectation is the loading manufacturer will use a pressure test gun to adjust his load, but the handloader will be stuck with published load data that doesn't vary, so the handloader needs a more consistent burn rate, even if it costs more to achieve that (and it does, which is why large scale ammo manufacturers buy in bulk and determine their own load data). Hodgdon has H335 blended to ±3% of a nominal burn rate value where some bulk purchases can vary up to ±20% (though 10% seems to be more common). Anyway, if the seller is telling you H335 load data applies, then that should mean he tested it (and did not assume that) and found the minimum data was be safe. Data beyond that may not be safe or may still be underloaded, as you found out.
__________________
Gunsite Orange Hat Family Member CMP Certified GSM Master Instructor NRA Certified Rifle Instructor NRA Benefactor Member and Golden Eagle |
July 8, 2012, 12:23 AM | #21 |
Senior Member
Join Date: April 4, 2011
Location: LA (Greater Los Angeles Area)
Posts: 2,598
|
Thanks Nick
I bought mine from Wideners ($85+HZ+SH). I know they tested 846, and they have a note saying how they tested it. I wish they did that for 844, but they just say "If you reload 223 you know this powder."
http://www.gibrass.com/gunpowder.html Says: "WC844 Original application is U.S. 5.56mm NATO Ball M193 (55gr) & M855 (62gr), plus Tracer M196 & M856. Typical starting load for 55gr bullet is 26gr, and 62gr bullet is 25gr. A ball powder which can be loaded with Hodgdon H335 data. Also works great in 7.62mm NATO (.308 Win.). This is pulldown powder. $100/8# jug. $376 for 4 jugs. $528 for 6 jugs ($88ea)" I trust their statement as it is consistent with TM-43-0001-27. I am not disputing your post. My point though, despite lot variances, "was 844 actually a different powder than H335?" I suspect 844, on average across all lots, actually burns slower. IF true (and that is a big IF) then 844 may be usable beyond H335 published loads, if it is actually a slower powder (and for me more useful than H335 is in loading 308). I think sellers of surplus powders are ALWAYS going to reference a faster commercial powder, and Never reference an actually slower powder. To do so would risk pressure increases beyond SAAMI ranges. I think referencing an actual matching speed commercial powder is unlikely because that would not be safe with lot variances. On the other hand, H335 may actually be a commercial version of 844 formula at the time Hodgdon introduced it, and both have been kept stable since. I don't know. I was hoping Quickload would be able to shed light on this. However, I was disappointed to find their website does not list 844 as one of the powders it has data for (must only have H335). I am just challenging the assumption they are really equivalent, or, do we reference H335 as convenient faster data to fill an inconvenient data void for an actual burn rate that is slower?
__________________
............ Last edited by Marco Califo; July 8, 2012 at 09:31 AM. |
July 8, 2012, 10:43 PM | #22 |
Staff
Join Date: March 4, 2005
Location: Ohio
Posts: 21,060
|
Marco,
That WC844 is H335 is something I got from the 2009 Hodgdon MSDS sheet, along with those for a number of other relabeled powders. They are in the table below. The current (2011) Hodgdon MSDS for spherical propellants no longer has the alternate names available, but the Winchester one availale (2009) still does. The only difference is bulk grade verses cannister grade. Hodgdon keeps back bulk lots that turned out to be extra fast and extra slow, then blends those with new bulk lots as need to adjust the average burn rate to within 3% of nominal, thus creating a cannister grade blend. I got that straight from the mouth of one of Hodgdon's technicians. You can call them and verify it for your own satisfaction. They also have held back lots that are exactly average burn rate for doing their load data development. Code:
| St. Marks | | Thales | | Hodgdon | Mil & OEM | Winchester | (ADI | IMR | ___________________|__Numbers___|________________________|__________|______________________|_ | | | | | HP-38--------------|-- OBP231 --|- 231 ------------------|----------|----------------------|- | OBP124 | AALite (WFL) | | Titewad | OBP132 | | | Tightgroup --------|-- OBP242 --|------------------------|----------|----------------------- | OBP465 | Super-Handicap (WSH) | | Longshot | OBP473 | | | Lil' Gun ----------|-- OBP516 --|------------------------|----------|----------------------- Hybrid 100V | SHP771 | | | | SMP224 | AutoComp | | -------------------|--- WAA90 --|- WST ------------------|----------|----------------------- H110 | WC296 | 296 | | HS-6 | WC540 | | | -------------------|--- WC748 --|- 748 ------------------|----------| H414 | WC760 | 760 | | H335 | WC844 | | | BL-C(2)------------|--- WC846 --|------------------------|----------|----------------------- H380 | WC852 | | | US869 | WC869 | | | -------------------|-- WMR780 --|- Supreme 780 ----------|----------|----------------------- | WXC170 | WSF | | Clays | | | AS30N | International Clays|------------|------------------------|- AS50N --|----------------------- Universal Clays | | | AP70N | H4227 | | | AR2205 | IMR 4227 second source H4198 -------------|------------|------------------------|- AR2207 -|----------------------- Benchmark | | | BM2 | H322 | | | AR2219 | -------------------|------------|------------------------|- AR2210 -|- IMR 8208 XBR -------- H4895 | | | AR2206H | Varget | | | AR2208 | H4350 -------------|------------|------------------------|- AR2209 -|----------------------- H4831 | | | AR2213 | H4831SC | | | AR2213SC | H1000 -------------|------------|------------------------|- AR2217 -|----------------------- Retumbo | | | AR2225 | H50BMG | | | AR2218 | -------------------|------------|------------------------|- AR2215 -|- IMR 4198 second source | | | AS25BP |- IMR Trail Boss The way the military develops a load is the bullets have to reach a certain velocity window within a certain pressure profile. If a particular bulk lot of powder cannot achieve that, the lot is rejected for use in that load. On another board a former Aberdeen Proving Grounds Test Director described how, in the 70's, they got two lots of WC852 (H380) for M2 Ball ammo, and how one lot would achieve the required velocities without the muzzle pressure getting too high for the Garand, but the other would not. They used both, but the latter lot was qualified for machinegun use only, and not for use in Garands. Unfortunately the DCM issued much of the machine gun stuff for Garand use during the 80's. As a result some op-rods met their maker prematurely. I still have some of those rounds. You can tell them by pulling the bullets and weighing the charges/ The average charge weight in the machine gun ammo is over 56 grains, while the good stuff is more like 53 grains, IIRC (haven't had any for awhile and don't recall an exact number; just that it was several grains lower). What you have is pull-down powder from ammo deemed to be getting too old for stockpiling, so you know it qualified correctly at one time or it would not have been loaded in the subsequently pulled-down cartridges in the first place. But you just don't know exactly what charge weight they chose for that specific lot. Bottom line, if you depend on recipes, only cannister grade powder will be sure match them well. Bulk lots may or may not. The cannister grades are indeed adjusted to about the average seen for the bulk grades, but being adjusted, they vary less from lot to lot.
__________________
Gunsite Orange Hat Family Member CMP Certified GSM Master Instructor NRA Certified Rifle Instructor NRA Benefactor Member and Golden Eagle |
July 9, 2012, 12:27 PM | #23 |
Senior Member
Join Date: May 9, 2011
Location: Boise, ID
Posts: 455
|
My .02 is that they are both great but the h335 is slightly cheaper.
If you are loading something else like a 308 round then buy Varget because you can use them in both calibers. |
July 9, 2012, 02:41 PM | #24 |
Senior Member
Join Date: September 22, 2011
Location: Illinois
Posts: 342
|
im surprised nobody mentioned TAC. my best results (in an AR)with TAC. currently using CFE223. its pretty good as well
|
July 23, 2012, 03:23 AM | #25 |
Senior Member
Join Date: April 4, 2011
Location: LA (Greater Los Angeles Area)
Posts: 2,598
|
844 is not = H335
844 is a bit slower.
"161 SP 10, Vectan 162 H-335, Hodgdon 163 R 903, RWS 164 WC 844 165 BL-C(2), Hodgdon 166 WC 846 167 SP 9, Vectan 168 2460, Accurate 169 SP 7, Vectan 170 Reloder lOx, Alliant 171 W-748, Winchester 172 W-748BR, Winchester 173 TAC, Ramshot 174 2495, Accurate 175 Reloder 11, Hercules 176 Reloder 12, Alliant 177 N135, Vihtavuori 178 IMR-4064, ll\1R 179 Brigadier 4065- Scot 180 Varget, Hodgdon 181 Leverevolution, Hodgdon 182 2520, Accurate 183 N-202, Norma 184 XMR-4064, Accurate 185 4064, Accurate " Attached list from: http://www.castpics.net/LoadData/Main.html
__________________
............ Last edited by Marco Califo; July 23, 2012 at 03:31 AM. |
Thread Tools | Search this Thread |
|
|