September 5, 2018, 04:28 AM | #1 |
Senior Member
Join Date: April 26, 2009
Posts: 105
|
11-48 issues
I have a 11-48 that will not fire on the second shot. The hammer is following the bolt home after the first shot. Any thoughts?
|
September 5, 2018, 02:48 PM | #2 |
Senior Member
Join Date: February 13, 2002
Location: Canada
Posts: 12,453
|
Mostly likely a sear wear issue. Or somebody who didn't know what they were doing tried to do a trigger job. The hammer is failing to recock. The barrel recoiling with the bolt?
Innards are stamped parts. One of 'em might be broken too. Does the second shot feed and chamber? Probably best to take it to a smithy who knows 'em.
__________________
Spelling and grammar count! |
September 5, 2018, 03:43 PM | #3 |
Senior Member
Join Date: February 28, 2008
Location: Michigan
Posts: 2,618
|
Sounds as if the gun needs a complete tear down and
deep cleaning of the trigger/hammer group. |
September 5, 2018, 07:04 PM | #4 |
Senior Member
Join Date: April 26, 2009
Posts: 105
|
I have taken it apart (Basic field strip) and and clean. Nothing appears to be broken...but, something is. Round two will chamber but not fire.
|
September 6, 2018, 06:58 AM | #5 |
Senior Member
Join Date: February 28, 2008
Location: Michigan
Posts: 2,618
|
There is dried oil/grease/dirt in the trigger/hammer group.
This needs to be cleaned in depth so the gun will operate correctly. |
September 17, 2018, 06:58 AM | #6 |
Junior member
Join Date: November 7, 2004
Location: Mid-Michigan
Posts: 449
|
I just got one in a trade. I took it out for a test round of trap, ran great. got it home to field strip it for a quick cleaning and found more crud inside than I have ever seen before, even compared to abused .22 semi autos. After a mineral spirits bath for the trigger/hammer group, bold disassembly and scrubbing with a brass brush (yes, that bad), and scrub down it is pristine inside. My recommendation is to first clean the heck out of it. The bolt is kinda goofy to get back together, well the firing pin installation anyway, but other than that is it really easy.
|
September 27, 2018, 05:44 AM | #7 |
Staff
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 41,374
|
Just a guess, but I'm thinking your sear spring is crapping out and isn't putting the proper tension on the sear during the action cycle, allowing the hammer to ride the bolt down.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza Baby Jesus cries when the fat redneck doesn't have military-grade firepower. |
September 27, 2018, 05:20 PM | #8 |
Senior Member
Join Date: November 10, 2014
Posts: 1,371
|
1st thing I would look at is buffer tube & spring in stock. Many guys have never
stripped their gun down. They clean barrel and spray out action, wipe down and put back into rack. The solvents & oils along with desolved residues end up in the buffer assembly. This can build up to the point it will short stroke the bolt. This can warp the links that ride the buffer. These can trap the hammer and slow it down to point the impact is not enough to fire the primer. While the 11-48 is off the Browning design the 1100 has similar buffer system and same problems and is often mistaken for a bad firing pin. |
September 28, 2018, 06:35 AM | #9 |
Staff
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 41,374
|
"1st thing I would look at is buffer tube & spring in stock."
Good call... I forgot that those were there... I'm betting you're right, the tube, spring, and follower are all gunked up.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza Baby Jesus cries when the fat redneck doesn't have military-grade firepower. |
Thread Tools | Search this Thread |
|
|