|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
July 19, 2018, 04:43 AM | #1 |
Senior Member
Join Date: September 11, 2012
Posts: 388
|
How to break in new pistols?
What’s your method/s to break in new pistols?
Thanks so much. |
July 19, 2018, 05:23 AM | #2 |
Senior Member
Join Date: June 2, 2006
Location: Bowling Green Virginia
Posts: 4,487
|
Read the manual, clean the gun, properly lube it, go to the range and shoot.
|
July 19, 2018, 06:30 AM | #3 |
Senior Member
Join Date: March 20, 2014
Posts: 2,084
|
X2^^
|
July 19, 2018, 06:49 AM | #4 |
Senior Member
Join Date: June 5, 2009
Location: Milwaukee, WI
Posts: 1,093
|
Clean and shoot.
Repeat often. |
July 19, 2018, 10:11 AM | #5 |
Junior member
Join Date: March 9, 2018
Location: NY
Posts: 90
|
i don't clean before i shoot, i see it as way to test the factory setting and capabilities. i put two clips through it, clean and head back home.
|
July 19, 2018, 11:16 AM | #6 |
Senior Member
Join Date: February 13, 2002
Location: Canada
Posts: 12,453
|
"...i don't clean before i shoot..." Your shift key is defective. All new firearms are shipped coated in a rust preventative coating that needs to come off before shooting. That includes the magazines.
There is no need to "break in" any firearm. As mentioned, field strip, clean, load or buy some ammo and go shooting.
__________________
Spelling and grammar count! |
July 19, 2018, 03:46 PM | #7 |
Member
Join Date: August 1, 2009
Location: SW FL year around
Posts: 56
|
So how many rounds is the min. # you writers feel comfortable shooting when you determine the gun is reliable??
Many people on these forums refer to 100 + rounds. My local Sheriff Dept. says 50 rounds. Anybody have an opinion? |
July 19, 2018, 04:19 PM | #8 |
Staff
Join Date: September 25, 2008
Location: CONUS
Posts: 18,468
|
Most sources I've seen say a minimum of 500 rounds with no stoppages is the criterion for establishing reliability if the gun will be used for carry/personal defense.
For a range toy? Whatever floats your boat. But there's a big difference between "break-in" and establishing reliability. Some of the premium 1911 makers (yes, I'm talking about Les Baer) won't talk to you about malfunctions unless/until you have put at least 500 rounds through the gun. To me, that's unacceptable. If I buy a new car and it keeps stalling every half mile going down the road, I'm not going to wait for 500 miles to show on the odometer before I take it back the dealer to fix it. I buy a car to take me from point A to point B. I buy a gun to send a projectile in the general direction I'm aiming when I pull the trigger. Both are machines. If either machine doesn't perform the intended function, it's defective and should be repaired or replaced by the maker. |
July 19, 2018, 05:16 PM | #9 |
Senior Member
Join Date: December 6, 2014
Posts: 6,446
|
Establishing reliability might take many rounds - it will depend on how many different types of ammo you intend to try to see which ones function best and give you acceptable accuracy
__________________
"I believe that people have a right to decide their own destinies; people own themselves. I also believe that, in a democracy, government exists because (and only so long as) individual citizens give it a 'temporary license to exist'—in exchange for a promise that it will behave itself. In a democracy, you own the government—it doesn't own you."- Frank Zappa |
July 19, 2018, 07:32 PM | #10 |
Senior Member
Join Date: October 17, 2014
Posts: 2,444
|
Field strip it, clean it, lube it, fire 200-300 absolutely trouble-free rounds through it, and I'm good to go.
|
July 19, 2018, 08:36 PM | #11 |
Senior Member
Join Date: May 1, 2018
Posts: 156
|
As everyone else has said. clean and lube it. But I personally wouldn't consider a gun reliable unless it can shoot 1000+ rounds without a stoppage for nightstand/carry. a couple hundred rounds is plenty reliable for a range gun. That may be excessive but many guns iv had experience with could easily do that.
|
July 19, 2018, 08:46 PM | #12 |
Senior Member
Join Date: December 10, 2014
Posts: 1,965
|
I just put 150 rounds thru the newest SD9VE last weekend. From experiences with the other three, I deem this one ready to go.
|
July 20, 2018, 07:35 AM | #13 |
Senior Member
Join Date: February 9, 2006
Location: Homes in Brooklyn, NY and in Pennsylvania.
Posts: 5,473
|
Reliability
Reliabity testing. It is a pipe dream. Test a gun all you want....two magazines, two boxes of ammo, ten boxes of ammo.....a firearm is a mechanical device. A mechanical device will fail sooner or later. There is no predicting when only that it will.
Shoot 500 trouble free rounds through your gun. There is no guarantee that the gun will not malfuncton on the 501st. In fact, the more trouble free rounds that you shoot the more lkely the gun is going to fail on the next shot (whenever that is)
__________________
“Auto racing, bull fighting, and mountain climbing are the only real sports ... all others are games.” Ernest Hemingway ... NRA Life Member |
July 20, 2018, 03:14 PM | #14 |
Member
Join Date: June 10, 2018
Posts: 67
|
I dont think I've ever cleaned a gun before shooting it, maybe I should but I probably wont start now. I just clean after shooting and if I wont be shooting for awhile i put it away a little wet. Never had any problems.
|
July 20, 2018, 03:27 PM | #15 |
Senior Member
Join Date: April 13, 2013
Location: N. Georgia
Posts: 1,150
|
Some guns are shipped dripping oil/preservative;
others not so much: some are dry as the proverbial bone. Recently took in a Beretta 92FS. It was dry. I lubed it a bit and now believe it's ready for testing, extensive shooting. When the gun comes dripping wet, I'll wipe the goo/oil off and relube it, oil it. Since revolvers don't actually need a lot of oil to run, I'll sometimes shoot them for a bit while dry. P.S.: I always check the barrels to see how they look and might run a patch through them. |
July 20, 2018, 04:23 PM | #16 |
Senior Member
Join Date: December 28, 2009
Location: North Central Illinois
Posts: 2,710
|
Thoroughly clean pistol to remove all preservatives. Oil about 10 times more than normal. Reoil after each and every mag. Lots of oil helps wash away any small machining burrs / chips that will come loose while shooting. Thoroughly clean again after range session. Done.
|
July 20, 2018, 04:25 PM | #17 |
Senior Member
Join Date: December 30, 2015
Location: My back yard
Posts: 971
|
Clean it shoot it, shoot it clean it, buy more ammo.
|
July 20, 2018, 05:08 PM | #18 |
Senior Member
Join Date: April 28, 2001
Location: CA
Posts: 1,768
|
Shoot the Gun!
Then shoot it some more!
Shoot it Shoot it Shoot it Shoot it until you have tried all the typical ammo you plan to use and have not had any hiccups. One you have made sure the gun is going to run. Clean it Oil it Keep it someplace safe. |
July 20, 2018, 06:20 PM | #19 |
Senior Member
Join Date: February 9, 2006
Location: Homes in Brooklyn, NY and in Pennsylvania.
Posts: 5,473
|
Ammo and reliability
I can see testing a new firearm in order to find out what type of ammo functions the most reliabiy. That is a bit different than testing the reliability of the gun itself.
__________________
“Auto racing, bull fighting, and mountain climbing are the only real sports ... all others are games.” Ernest Hemingway ... NRA Life Member |
July 21, 2018, 12:33 AM | #20 |
Senior Member
Join Date: June 1, 2013
Location: Now relocated to Texas
Posts: 2,943
|
RC has the answer, don’t worry about counting rounds just shoot the beans out of it until you are comfortable with the firearm’s performance.
|
July 21, 2018, 05:00 AM | #21 |
Senior Member
Join Date: May 31, 2013
Location: East Texas
Posts: 1,705
|
I've gotta agree, just shoot em' and don't worry about round count. I think the clean and lube thing really gets blown out of proportion. I clean my guns, but only every now and then. Some folks really get too worried about that stuff. It they work reliably that's all that counts.
|
July 23, 2018, 12:57 AM | #22 |
Senior Member
Join Date: March 6, 2013
Posts: 640
|
Clean lube and shoot. I use 500 (half defense loads) with no hiccups as a minimum before i carry it. YMMV
|
July 23, 2018, 07:42 AM | #23 |
Senior Member
Join Date: January 22, 2005
Location: Kentucky
Posts: 3,624
|
Well...I shoot the **** out of them....Rod
__________________
Cherish our flag, honor it, defend it in word and deed, or get the hell out. Our Bill of Rights has been paid for by heros in uniform and shall not be diluted by misguided governmental social experiments. We owe this to our children, anything less is cowardice. USAF FAC, 5th Spl Forces, Vietnam Vet '69-'73. |
July 23, 2018, 08:04 AM | #24 |
Senior Member
Join Date: June 10, 2005
Location: SW Florida
Posts: 2,747
|
I never shoot a new handgun without first cleaning out all the crap left behind from manufacturing. I don't believe barrel break in is as important as breaking in everything else. I won't consider a gun ready for EDC until I've run at least 300-400 rounds thru it, tried various ammo's to see what it prefers, given time for everything to wear in a little, and can go thru 200 rounds without a failure. Range guns however, I clean, lube, and shoot the bejesus out of, with less care or concern for round count.
PS...I think Kahr used to say 400 rounds was their minimum before they considered their guns broken in and safe to carry.
__________________
God's creatures big and small, eat them one, eat them all. |
July 23, 2018, 08:31 AM | #25 |
Senior Member
Join Date: October 12, 2002
Location: The same state as Mordor.
Posts: 5,569
|
clean, lube, shoot
__________________
"As was the man of dust, so also are those who are of the dust, and as is the man of heaven, so also are those who are of heaven. Just as we have borne the image of the man of dust, we shall also bear the image of the man of heaven. " |
|
|