October 6, 2012, 12:46 PM | #1 |
Senior Member
Join Date: July 20, 2001
Posts: 641
|
Mossberg feed tube spring
Can someone tell me how long a Mossberg 500 can be kept loaded before the feed tube spring becomes weak? I have a 500 with the eight shot tube that is kept loaded for HD and seldom fired.
|
October 6, 2012, 01:44 PM | #2 |
Senior Member
Join Date: February 11, 2012
Location: Williamsburg, Va.
Posts: 1,528
|
Forever. Modern coil springs do not lose strength being kept in static loading.
|
October 6, 2012, 03:00 PM | #3 |
Senior Member
Join Date: January 19, 2007
Posts: 2,663
|
I left mine loaded for 20+years, with the occasional unloading to transport it to the field. Is the spring sofer now? Yes. Does it still work? Yes.
Can you change the spring out? Yes. Is it hard? No. Wolf Springs has them. |
October 6, 2012, 03:43 PM | #4 |
Senior Member
Join Date: July 20, 2001
Posts: 641
|
I would just order a new spring from Wolf, but the feed tube doesn't want to unscrew.
|
October 6, 2012, 04:17 PM | #5 |
Senior Member
Join Date: May 28, 2007
Location: swamp people
Posts: 539
|
channel locks
|
October 6, 2012, 04:34 PM | #6 |
Senior Member
Join Date: January 19, 2007
Posts: 2,663
|
The mag tube is thin metal except at the very end where the barrel attaches. There it's thick for about 1/2". You want to use a strap wrench, or , as I did, wrap a piece of brass around it and grab it (carefully) with vice grips. Mine turned out very easily.
Remove the tubes, remove the follower and spring. Clean the interior of the mag tube, since you'll only get this chance every 30 years or so... Insert the new spring and follower, put some low strength Loc-Tite on the threads, and reassemble. This is a good technique to know, as mag tubes are easy to dent, and you should know how to replace one. |
October 6, 2012, 11:01 PM | #7 |
Senior Member
Join Date: April 23, 2012
Location: Texas ... north of houston, east of el paso
Posts: 214
|
just had to replace mine because some idiot put a pencil in it for a plug.
i just disassembled it removed the forend and put the receiver between my legs and twisted the tube off with my hands. the spring i found at www.midwayusa.com for $3.99 plus shipping...good luck |
October 7, 2012, 07:02 AM | #8 |
Senior Member
Join Date: September 19, 2012
Location: Somewhere out there
Posts: 184
|
You should be fine...just every 4 months or so it would be a good idea to cycle a few shells to keep some kind of spring pressure. You don't wanna have to need your shotgun and your spring is too weak to load the chamber. Good luck!
__________________
12 Gauge Fury! |
October 7, 2012, 02:06 PM | #9 |
Junior member
Join Date: February 2, 2008
Posts: 3,150
|
If you don't know how old your mag spring is or who made it buy a new one from Wolff. The mag spring is just about the most critical part in a pump gun. Most people figure out that they need a new mag spring when the gun starts to misfeed on the last couple of rounds. Don't wait that long. Just replace it for a few bucks. When you do you'll immediately notice how much more force is required to insert the first round into the mag. That's what you want to feel. If you're going to keep this gun loaded for years at a time consider downloading it by one round. The spring will last much longer than it will if you load it full up. Most shells will begin to swell long before the spring starts to weaken. Change them out once a year.
|
October 7, 2012, 03:00 PM | #10 |
Junior member
Join Date: June 23, 2009
Location: Orange County, CA
Posts: 2,149
|
Dave McC's post elsewhere reminded me of an issue. Consider that while modern coil springs may not lose strength from being stored compressed, shot shells may become distorted if kept stored in a fully loaded tube. Hence, you might want to keep one less than max in the mag.
|
March 16, 2013, 03:53 PM | #11 |
Junior Member
Join Date: September 23, 2007
Location: Hudson Valley area NY
Posts: 1
|
Mag Spring
Had to order a new spring for my Mossberg 500c...the last round would not chamber, keeps falling out the bottom. I don't have the new spring as of yet, but I can't get the feed tube loose and don't want to damage it. Is there a tool with a locknut that goes into the feed tube so you can use a wrench to remove it. Seems like a good idea if you can match up the threads of the feed tube.
|
March 17, 2013, 10:01 AM | #12 | |
Staff In Memoriam
Join Date: October 31, 2007
Location: Western Florida panhandle
Posts: 11,069
|
Quote:
If neither the gun or dryer is available, completely tear down the gun and put magtube/receiver assembly in the oven at 200 or so to get it hot... Brent |
|
Thread Tools | Search this Thread |
|
|