February 10, 2018, 12:18 PM | #1 |
Senior Member
Join Date: May 5, 2012
Location: Pennsylvania
Posts: 172
|
400 FPS under manual?
I loaded up some 55 grain nosler varmint bullets for a 243. According to nosler, I should have been getting 3950 with the load I was using. I got 3485. That got me wondering as to why the big discrepancy?
Load info...Once fired Rem brass, CCI#200 primer, powder was 50 grains of H4350. Projectile was Nosler 55 grain Varmageddon. Average velocity was 3485 with an ES of 32. OAL was 2.710 (.015 OFF LANDS) Rifle is a Ruger M77 MKII with a 22 inch barrel. I did notice in the manual that they have an OAL listed at 2.590. Would that alone make that difference? Or is something else happening here? Am scratching my head on this one... |
February 10, 2018, 12:28 PM | #2 |
Senior Member
Join Date: March 24, 2006
Location: Northern Utah
Posts: 705
|
Relax. A lot of variables there. Each of the components going into your loads are from a different batch than what the Nosler gang found in their testing. All they can do is tell you what it did for them. Now you tell us what it did for you. Thanks for the report.
|
February 10, 2018, 12:52 PM | #3 |
Senior Member
Join Date: March 1, 2009
Posts: 4,232
|
Nosler tests their ammo using a 24 inch Lilja barrel and Nosler cases with a volume of 53.0 grains of water and a Remington 9 1/2 primer. This could account for some of the difference. I have seen velocity both increase and decrease with the round count on the barrel, speeding up for the first couple of hundred then decreasing a couple of hundred when the barrel gets into the mid 1K range.
H4350 is pretty stable temperature wise with a .35 fps/f burn rate but temps could be a minor factor Then there are chrono accuracy factors. How much faith do you have in the chrony? Can you zero at 100 and then dial in at 500 + and be within a half MOA or better on elevation? Using my balistic calculator using the hollow point Varmageddon you are stable out to about 500 yards and with the tipped you could stretch it out to 700 or so and still be stable If it is accurate at the distance you plan on shooting then I would not sweat the numbers too much.
__________________
“How do I get to the next level?” Well, you get to the next level by being the first one on the range and the last one to leave.” – Jerry Miculek |
February 10, 2018, 01:10 PM | #4 |
Junior member
Join Date: January 5, 2018
Location: Northeast USA
Posts: 232
|
That's a big swing. The 2" barrel difference, nor the primer selection would cause such a variance. My first reaction would be to verify the Chronograph was set up properly [mine had the ability to change the distance of the screens. Generally, if things are off, I've placed them too far apart or close]. If the chrony is OK, I'd pull a bullet and reconfirm the weight of the charge. I checked the Hodgdon website, but they're not showing H4350 as a powder selected for the 55gr. It doesn't pop up until you get to the heavier bullets.
|
February 10, 2018, 01:25 PM | #5 |
Senior Member
Join Date: February 13, 2002
Location: Canada
Posts: 12,453
|
Using a 24 inch Lilja barrel with a 1 in 10 rifling twist. Book velocities are averages, but only matter if your rifle is exactly the same and so are the climatic conditions.
Your Ruger uses a 1 in 9 twist and is 2" shorter. That will change your velocity results. Wouldn't worry about it if the load is accurate though. You work up to the 50 grain max load or just pick it? Kind of odd the Hodgdon didn't test H4350 with 55 grain bullets. They didn't test IMR4350 with 55 grain bullet either though.
__________________
Spelling and grammar count! |
February 10, 2018, 02:06 PM | #6 |
Senior Member
Join Date: May 5, 2012
Location: Pennsylvania
Posts: 172
|
I worked up to it starting at 47 grains. All the charges were on average -400fps from manual.
|
February 10, 2018, 02:18 PM | #7 |
Senior Member
Join Date: December 27, 2017
Posts: 460
|
I had a similar issue when I was working up loads with Superformance powder. I was under velocity by almost 200fps. My seating depth was based on a miscalculation I had made on my lands distance. I thought I was just off the lands with a COL of 3.375 when I was in fact jamming. I had high pressure signs and stopped. Later I seated the bullets deeper to a COL of 3.320" which was actually .010" off the lands. It put me right on with Hodgdon's data.
Speaking of Hodgdon. Their latest data does not list H4350 for that bullet. What Hodgdon does list never comes close to 3950 FPS which is really fast! The powder charge that you are using is also a compressed charge. Case volume could come into play there too. One more thing. you might go back and double check your COL a while after you load. Sometimes compressed loads will push the bullet back out. |
February 11, 2018, 09:02 AM | #8 |
Junior member
Join Date: February 2, 2010
Posts: 6,846
|
One reason I see is the use of such a "slow" powder with a very light for caliber bullet in a "short" (vs 24-26" anyway) barrel. Three strikes right there.
|
February 11, 2018, 10:11 AM | #9 |
Senior Member
Join Date: June 23, 2013
Location: Central Taxylvania..
Posts: 3,609
|
From my experience i've found the Nosler manual optimistic to word it nicely.
Pure fantasy to word it not so nicely. Still don't know why in the world i bought their latest manual... |
February 11, 2018, 10:16 AM | #10 | |
Senior Member
Join Date: March 1, 2009
Posts: 4,232
|
Quote:
https://load-data.nosler.com/ there are a few omissions here, for example their 69 grain .224 bullet has no data so I use 69 grain SMK data from Sierra
__________________
“How do I get to the next level?” Well, you get to the next level by being the first one on the range and the last one to leave.” – Jerry Miculek |
|
February 12, 2018, 09:11 AM | #11 |
Senior Member
Join Date: May 5, 2012
Location: Pennsylvania
Posts: 172
|
I was also wondering about the powder being on the slow side. I will try a powder with a faster burn rate something in the IMR 3031 range.
|
February 12, 2018, 09:47 AM | #12 | ||
Senior Member
Join Date: June 22, 2017
Posts: 1,011
|
Quote:
Quote:
With that in mind, could a difference of 0.120 inches make a big difference in the results you got? It's certainly within the realm of possibility. If you want the results the publisher got in the book, then duplicate what the publisher did in the book. Don't change it to suit your own preferences and expect to get the same result. |
||
February 12, 2018, 09:57 AM | #13 |
Senior Member
Join Date: April 20, 2009
Location: Helena, AL
Posts: 4,424
|
My 243 likes 4064 and RL 17. I also agree that real world results at the range are usually different than the manufacturers lab. For the record, I've always seated bullets to the listed OAL without issue. When you get to 30fps or less ES, you've got an accurate load.
|
February 13, 2018, 11:07 AM | #14 |
Senior Member
Join Date: March 24, 2006
Location: Northern Utah
Posts: 705
|
"Am scratching my head on this one..."
I have to ask: Why do you reload? For me at the beginning it was to save a few bucks on the ammo I was shooting. Later as I got into it, it became interesting to work up a load for the rifle in use and get those loads to repeat. IOW hit the same spot each shot. I have never used a chrono. I don't really care how fast they are going, what I do care about is hitting the target! |
February 13, 2018, 11:12 AM | #15 |
Junior member
Join Date: June 13, 2017
Posts: 429
|
A chrono can help out a lot more than showing just how fast bullets go.
|
February 13, 2018, 11:27 AM | #16 | |
Senior Member
Join Date: March 1, 2009
Posts: 4,232
|
Quote:
Now I don't sweat the flyers or wind when developing a load . If I find a good node 3 or 4 tenths wide I don't have to be so picky on whether the powder measured is 41.1, 41.2, or 41.3 grains. If I load for 41.2 and the load is really 41.1 or 41.3 grains due to scale error it will give me the same velocity within a few FPS. That way I can be pretty much assured that the bullets will hit in the same spot if I am using good technique and the wind does not send me off to la la land Do a internet search for velocity flat spots, the theory has been around for a while now but I just learned of it myself edit - you can accomplish the same thing and find those wide nodes without a chrono by using Dan Newberrys' OCW method here is a link where Newberry himself chimes in down in the comments section. http://www.65guys.com/load-development-part-1-of-2/ The theory goes back to at least 2013 when Erik Cortina posted about it http://forum.accurateshooter.com/thr...yards.3814361/
__________________
“How do I get to the next level?” Well, you get to the next level by being the first one on the range and the last one to leave.” – Jerry Miculek Last edited by hounddawg; February 13, 2018 at 11:49 AM. |
|
February 13, 2018, 06:06 PM | #17 |
Senior Member
Join Date: June 17, 2010
Location: Virginia
Posts: 6,894
|
QL tells that that with...
- That bullet - That barrel length - That Powder - That weight - That OAL... I should looking at 3,700fps/63ksi/95% burn. If I'm off by 50fps w/ QL, I'm not surprised. 100fps... then I'm mildly surprised. ....but more that 200 ? I'd go back and double check things. . Last edited by mehavey; February 13, 2018 at 06:22 PM. |
February 13, 2018, 09:30 PM | #18 |
Senior Member
Join Date: April 10, 2012
Location: San Diego CA
Posts: 6,876
|
[QUOTEMy 243 likes 4064 and RL 17. I also agree that real world results at the range are usually different than the manufacturers lab.][/QUOTE]
I don't load for the cartridge but thought 4064 burn rate is where I thought would be the next try for the light bullets . IMR 3031 seems like a really fast powder for the cartridge .
__________________
If Jesus had a gun , he'd probably still be alive ! I almost always write my posts regardless of content in a jovial manor and intent . If that's not how you took it , please try again . |
February 13, 2018, 09:47 PM | #19 |
Senior Member
Join Date: June 15, 2008
Location: Georgia
Posts: 10,808
|
There are a lot of factors that can account for slower speeds. All have already been mentioned. But all of those factors combined shouldn't account for over 100-150 fps difference.
Just guessing, but I'd check to be sure that both the scales and chronograph are accurate.
__________________
"If you're still doing things the same way you were doing them 10 years ago, you're doing it wrong" Winston Churchill |
February 13, 2018, 10:05 PM | #20 |
Senior Member
Join Date: December 27, 2017
Posts: 460
|
What other powders do you have on hand?
|
February 13, 2018, 10:25 PM | #21 |
Senior Member
Join Date: January 6, 2008
Location: Northeast Colorado
Posts: 1,993
|
I bought a pound of IMR4451. Supposed to be wonderful. I worked up loads for 243 Win. With a couple different bullets, the velocities were low by around 300 fps. Tried H4350, and the Nosler data was considerably different than my loads. So, I used data from Hodgdon for H4350 and 90 gr. Bullets. My results correlated closely to the Hodgdon data. Hodgdon uses heavier powder charges than Nosler in this combination. It bumfuzzles me why Nosler loads are 2-3 gr. less than Hodgdon.
Nothing is set in stone for load data vs. actual results. Powder varies from lot to lot. Individual guns are different. Chrony accuracy may be off. Etc etc. My jug of IMR4451 may be from a wimpy lot. |
February 13, 2018, 11:18 PM | #22 |
Junior member
Join Date: February 2, 2010
Posts: 6,846
|
"I have never used a chrono. I don't really care how fast they are going, what I do care about is hitting the target!"
Not everyone has those parameters. A hunting load that's "good enough" and 200 fps faster is a PLUS in the field. |
February 14, 2018, 07:23 AM | #23 |
Senior Member
Join Date: May 5, 2012
Location: Pennsylvania
Posts: 172
|
|
February 14, 2018, 07:28 AM | #24 |
Senior Member
Join Date: May 5, 2012
Location: Pennsylvania
Posts: 172
|
I may be able to get some H414 to try as well.
How do you check if the scales are accurate? I have the RCBS beam scale....I recently weighed some bullets that were supposed to be 250 grains and my scale showed them at 249.9. Also, how can you verify a chrono? I really do not think that is off since I used it the same day to chronograph a 308 with 130 grain ttsx. According to manual I should have been at 3130 fps and i was at 3015 with a 20 inch barrel, which seemed much more reasonable to me. |
February 14, 2018, 07:52 AM | #25 |
Senior Member
Join Date: December 27, 2017
Posts: 460
|
Is there any chance you may have been using your 7828? Quickload puts your data very close to the velocity you gave with that powder. If you were on the lands it puts the velocity right at 3510. I know it's hypothetical but I have made some dandy mistakes in reloading.
The fact that you had "wimpy" velocities with another powder may suggest other issues. 400 fps is pretty far off. Also .1 grain is not worth fretting over as far as bullet weight. You could verify your chronograph with a magnetospeed. |
|
|