|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
October 31, 2012, 06:22 PM | #1 |
Junior Member
Join Date: October 31, 2012
Posts: 6
|
Pre-64 300 H & H Magnum
Hi. My father has decided to give away his guns to his children since he is getting older. Since I am the only one of his kids that hunt, he gave me first choice of his hunting rifles. The one that I wanted and chose was a 1950 Pre-64 Winchester 300 H & H Magnum. Now that I have the rifle, I would like to put a scope on it. I currently hunt with a 30-30 that has a scope but sometimes that shots are a little too far for that caliber. Anyway, there are two threaded holes in front of the bolt on top but on the back of the bolt there is two holes on the side. Is there any way to mount a scope on this gun (preferably a modern scope) by using the existing holes? I really don't want to change the gun by having a hole drilled and tapped on top. I hope the pictures can give an idea what I am talking about. Thanks.
|
October 31, 2012, 08:14 PM | #2 |
Senior Member
Join Date: April 18, 2009
Location: mountains of colorado
Posts: 977
|
Your rifle should have holes drilled on the rear bridge as well. Modle 70's were drilled for modern scope bases by 1946, so you wont have to drill anything. Scope bases are currently produced by Leupold and Weaver. The holes on the side are for a reciever sight. You choose wisely. Your rifle is the king of commerial bolt guns. The Riflemans Rifle is it nickname. Any alteration will severly reduce value. How about some complete photos?
|
October 31, 2012, 08:26 PM | #3 |
Senior Member
Join Date: May 27, 2007
Posts: 5,261
|
These older M70's were either used with long tube scopes that used dove tails on the barrel and the receiver ring, or used a wierd scope base. I looked for pictures of Noske, or any pre war mounts, could not find one.
The holes on the left rear of the receiver were for the Lyman 48WJS iron sight. You either have to find a vintage mount and scope (cost between ouch! & Bong!) or drill and tap the receiver bridge for a modern mount. Drilling and tapping will just about halve the collector's value of a pristine pre 64, so think carefully about this.
__________________
If I'm not shooting, I'm reloading. |
October 31, 2012, 08:44 PM | #4 |
Junior Member
Join Date: October 31, 2012
Posts: 6
|
Here are some more pictures of the rifle. I really don't want to drill and tap it although to shoot at long distances with open sights isn't much of an option either. If I decide to spend the money on a mount that will fit this gun without drilling a tapping it, how difficult is it to find the mount?
|
October 31, 2012, 08:50 PM | #5 |
Junior Member
Join Date: October 31, 2012
Posts: 6
|
Here are a few more pictures.
|
October 31, 2012, 09:06 PM | #6 |
Senior Member
Join Date: October 25, 2001
Location: Alabama
Posts: 18,543
|
There was a period scope mount that attached to the receiver sight screw holes and either the front receiver ring holes or to a base in the rear sight dovetail. A Stith Instal It Yourself mount, I believe. It would be a good trick to find one and then you would have to have a suitable scope, one without an enlarged objective bell, which would limit you to maybe 3X.
|
October 31, 2012, 10:02 PM | #7 |
Senior Member
Join Date: October 18, 2006
Posts: 7,097
|
http://www.midwayusa.com/product/626...il-matte-steel
This is the type of scope Jim Watson was referring to, and it will fit fine. Keep the rear sight that is removed to make way for the front scope base. Jimro
__________________
Machine guns are awesome until you have to carry one. |
November 1, 2012, 09:59 AM | #8 |
Senior Member
Join Date: May 27, 2007
Posts: 5,261
|
Does not look like your rifle has been cut down or a rubber recoil pad added. It is easily a $1,000 dollar rifle. The 300 H&H is an uncommon chambering. Muck with it and the value will drop.
__________________
If I'm not shooting, I'm reloading. |
November 1, 2012, 10:06 AM | #9 |
Staff
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 41,390
|
"There was a period scope mount that attached to the receiver sight screw holes and either the front receiver ring holes or to a base in the rear sight dovetail. A Stith Instal It Yourself mount, I believe."
Bingo! I couldn't remember Stith. I was sitting here going S.... S.... S... damn it, I know the name! Yes, Stith made mounts that used the side holes. They worked, but they weren't the most stable. On the plus side, you won't pay a lot for one of these mounts. I've seen them go for $40 and $50, and they seem to be relatively common. The the minus side, they have not been made for years, and you'll have to have patience in finding one. Check E-Bay, Gunbroker, and Auction Arms.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza Baby Jesus cries when the fat redneck doesn't have military-grade firepower. |
November 1, 2012, 10:10 AM | #10 |
Senior Member
Join Date: October 25, 2001
Location: Alabama
Posts: 18,543
|
Actually, not, Jimro. That is a knockoff of a Unertl target scope. At one time you could get bases for it that would fit the receiver ring and rear sight dovetail. So it could be made to work if you could find those bases.
What I referred to was like the one advertised here: http://www.ebay.ca/itm/Bear-Cub-Mast...item27cc5611aa It uses the receiver ring holes and the left side peep sight holes. There is also a version that has a long sleeve that goes over the objective end and sets in the open sight dovetail. |
November 1, 2012, 05:13 PM | #11 |
Senior Member
Join Date: April 18, 2009
Location: mountains of colorado
Posts: 977
|
Does everyone see what I see? A type 3 action WITHOUT the rear bridge drilled. All type 2 actions had the rear bridge drilled. In 45 years of collecting and studying model 70's, I have never seen or heard of a type 3 action not drilled. Could we please get a close up photo of the rear bridge?
|
November 1, 2012, 08:37 PM | #12 |
Junior Member
Join Date: October 31, 2012
Posts: 6
|
Here are some more pictures of the rifle. What is the difference between a type 2 and type 3 action?
|
November 1, 2012, 08:39 PM | #13 |
Junior Member
Join Date: October 31, 2012
Posts: 6
|
One more picture.
|
November 1, 2012, 08:51 PM | #14 |
Junior Member
Join Date: October 31, 2012
Posts: 6
|
The bases that are for sale on ebay; would it fit the long action found on a 300 H & H magnum or would it only fit a short action such as a .270. Would I need to measure the distance between the receiver ring holes and the left side peep holes?
|
November 1, 2012, 08:52 PM | #15 |
Senior Member
Join Date: February 13, 2006
Location: Washington state
Posts: 15,248
|
I see them all the time with the front ring drilled/tapped and the rear bridge not drilled/tapped on top. That was actually normal for a few years after WW2. But it's probably not something most people look for.
__________________
Never try to educate someone who resists knowledge at all costs. But what do I know? Summit Arms Services Last edited by Scorch; November 1, 2012 at 08:59 PM. |
November 1, 2012, 09:05 PM | #16 |
Junior Member
Join Date: February 19, 2012
Posts: 14
|
Your rifle is a 100% original Model 70 in a not too common caliber,with a undrilled rear receiver.I would leave it alone in the original condition,many have had recoil pads added,receivers drilled and tapped which reduces the value.
|
November 1, 2012, 09:26 PM | #17 |
Member
Join Date: August 22, 2011
Location: NW Georgia
Posts: 17
|
This is a rifle passed from your father to you.
Can you conceive of a time that you might want to sell the rifle, or do you see it being passed on through the family? If you may sell it some day, leave it alone. If you plan to keep it in the family, tap it, install modern rings and a scope, and make the rifle useful for you. Would you rather think of you father every time you pull the trigger on a rifle you can use, or every time you open the door and look at your safe queen? Yes you may devalue the rifle, but we aren't talking about a Purdey here. The flaming begins in 3..2..1.. |
November 1, 2012, 10:14 PM | #18 |
Senior Member
Join Date: April 18, 2009
Location: mountains of colorado
Posts: 977
|
As stated I have seen probably a thousand early model 70,s over the years and never a type 3 without rear bridge drilled. Quite unusal. A normal model 70 base will not fit a magnum action rifle. Tne only solution that wont severly reduce values is to aquire a STITH mount from ebay or like auction sites and instead of using the old stlyle front " ring" instead use the front base and ring of a modern mount and use the STITH rear mount that uses the existing reciever sight holes. This will allow a standard 2 occular scope and a sturdier set up. Even though STITH bases are expensive, drilling an undrilled base is far more expensive in reduced collector value.
|
November 2, 2012, 02:39 PM | #19 |
Senior Member
Join Date: October 18, 2006
Posts: 7,097
|
Jim Watson,
That scope is a reproduction of the Unertl the USMC used on their 30-06 M70 rifles in the 50's and 60's. I linked to it as an example of something that would be "period correct" and have the forward scope mount in the rear sight dovetail. Jimro
__________________
Machine guns are awesome until you have to carry one. |
November 3, 2012, 10:33 AM | #20 |
Senior Member
Join Date: September 18, 2011
Location: North Idaho
Posts: 161
|
+1 for what Buzzdoc said. I inherited several of my father's rifles and some I kept original and some I altered for my use. Value - schmalue; it was Dad's gun and now it's mine.
What a cool gun! A pre-64 Mod 70 in 300H&H is about as righteous as it gets. What a wonderful big game rifle. Enjoy your gun, it's a great one. |
November 5, 2012, 06:54 PM | #21 |
Senior Member
Join Date: December 3, 2002
Posts: 1,264
|
Should be easy to hit stuff at 400+yds with irons. I'd enjoy it as-is.
|
November 6, 2012, 03:26 PM | #22 |
Senior Member
Join Date: December 13, 2009
Location: central Wisconsin
Posts: 2,324
|
I would have the back receiver top drilled and tapped by a gunsmith so you could use standard bases.
Or a gunsmith could probably make you a rear base that would allow you to use standard rings. |
November 6, 2012, 09:14 PM | #23 |
Senior Member
Join Date: April 20, 2009
Location: Helena, AL
Posts: 4,424
|
I'm Confused
You do have a rare M70; however, if the stated purpose is to hunt, TAP it! The value is not the gun, it's from your father. I surmise that it will stay in your family. The 300 needs a scope and good reloads for a truly marvelous hunting rifle.
|
|
|