![]() |
![]() |
#1 |
Senior Member
Join Date: November 19, 1999
Location: Woodbury TN
Posts: 138
|
Homemade gas checks?
Now that g/c's are getting absolutely rediculous Im trying to think of an alternative
What if: when seating the bullet place a piece of tin foil from the wifes cuboard between the bullet and the case....I wonder |
![]() |
![]() |
#2 |
Senior Member
Join Date: December 9, 1999
Posts: 4,131
|
Hornady gas checks are not rediculous.
__________________
Favor the X. Steve Smith NRA Life Member |
![]() |
![]() |
#3 |
Senior Member
Join Date: October 25, 2001
Location: Alabama
Posts: 18,541
|
I don't know if that would be thick enough to work, cheap to try, though.
There was once a little device called a Tap-Check that would form gas checks out of aluminum can stock. Beer to bullets. They also made the Tap-Cap to make percussion caps. Don't know what they suggested for priming compound. As you might expect, I don't remember the maker and can't find them in any of several Handloader's Digests. There is the Venture Soft Gas Check, just a sheet of high-temperature wax to cookie-cut over the case mouth and form a wax wad. Lots of black powder shooters use sheets of beeswax that way. Velocities are low, of course |
![]() |
![]() |
#4 |
Member
Join Date: July 20, 2001
Location: ALABAMA
Posts: 78
|
unless I'm mistaken(happens alot) the hanned line has a aluminum can to gas check tool...not sure but if you can find their web site it should say.
|
![]() |
![]() |
#5 |
Senior Member
Join Date: August 15, 2000
Location: Sugar Land, Tx
Posts: 1,507
|
dntorbert...
Thanks for the heads up. Here's their instructions for their gas check maker. http://www.hanned.com/MkIIPB_Instr.html Pretty cool stuff
__________________
Ronnie- Proud Veteran, Neocon, Warmongering, Baby-Pincher |
![]() |
![]() |
#6 |
Senior Member
Join Date: March 21, 2000
Posts: 1,396
|
I read about someone using old egg cartons as gas checks, but he recommended using a compressed powder charge to keep the check against the bottom of the bullet.
__________________
There are two types of men: those with guns, and those at their mercy. |
![]() |
![]() |
#7 |
Senior Member
Join Date: October 29, 1999
Location: Dewey, AZ
Posts: 12,858
|
Unless one is going beyond the 1,800-2,000 fps range...
Good lube will usually obviate the need for gas checks. With smokeless powder. Sam |
![]() |
![]() |
#8 |
Junior Member
Join Date: April 27, 2005
Posts: 7
|
It looks like the Hanned web site it gone (someone posted he closed the business). Does anyone have ANYTHING on the gas check maker? Instructions? Photos? Reference articles (maybe in Handloader magazine)? Looking for a cheaper solution than Corbin's gas check maker. Any info would be greatly appreciated. Thanks.
|
![]() |
![]() |
#9 |
Junior Member
Join Date: October 8, 2004
Posts: 9
|
"They also made the Tap-Cap to make percussion caps. Don't know what they suggested for priming compound. As you might expect, I don't remember the maker and can't find them in any of several Handloader's Digests."
They suggested using the caps that are used for toy guns for the primer. If I remember correctly, they suggested using the ones made in the US because they had more bang to them. It is in either the current midway usa or midsouthshooterssupply master catalog. If I find time to figure out which one I will post the page number. |
![]() |
![]() |
#10 |
Junior Member
Join Date: October 8, 2004
Posts: 9
|
Tap-o-cap is on page 59 of midsouth shooter's supply's master catalog. Upper left hand corner. Nothing about gas checks though.
|
![]() |
![]() |
#11 |
Senior Member
Join Date: October 15, 2004
Posts: 934
|
Hanned is out of business.
The folks over on Cast Boolits do a group buy from Gater now and then that gets checks down to a reasonable price and they are about due for another. You could go there and ask about getting in on the next group buy. Catch on that deal is that you need to buy 5k of a caliber. Good part is that Gater is sole source for .41 GC and maybe some other stuff. http://castboolits.gunloads.com/forumdisplay.php?f=10 |
![]() |
![]() |
#12 |
Senior Member
Join Date: May 15, 2002
Location: Michigan
Posts: 1,429
|
http://www.corbins.com/gascheck.htm
They also make something that turns spent rimfire .22 shells into jackets for .223 type bullets. http://www.corbins.com/jackets.htm#rfjm
__________________
I'm not just a gun. I'm YOUR gun. (Hold me.) |
![]() |
![]() |
#13 |
Member
Join Date: November 12, 2004
Location: New Mexico
Posts: 62
|
Homemade Gas Checks
You know, I find the greatest ideas and topics here. A homemade gas check sounds like a great idea! What I am thinking is the aluminum can idea and using a gromet punch, If I could only find one with the right diameter... Just imagine, missing your deer (or other target) with the bullet but taking it down with a flaming aluminum disc as a backup! JK, but I am interested as well but don't think I need it. Bill BTW, I don't find them to be expensive at all. Try www.MidwayUSA.com
__________________
A Proud Veteran, USN USS Whipple FF 1062 USS Dixon AS 37 USS Jason AR 8 USS Kitty Hawk CV 63 |
![]() |
![]() |
#14 |
Senior Member
Join Date: May 15, 2002
Location: Michigan
Posts: 1,429
|
$20 /1000 isn't that bad.
Certainly not worth it (To me.) for all that extra hand labor. But what do I know, I'm not a fan of gas checks anyway.
__________________
I'm not just a gun. I'm YOUR gun. (Hold me.) |
![]() |
![]() |
|
|