|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
August 9, 2018, 06:29 PM | #1 |
Member
Join Date: February 25, 2011
Posts: 31
|
How to remove and replace a broken shotgun bead
I have a Springfield/J. Stevens Model 311/530 SxS 20 gauge with a 5100 frame probably mader between 1940-48. I received this in a trade and it is in very good shape except fotr the sights. As showen in the attached photos, the rear bead is broken off flush with the rib and the front sight appears to be a slotted screw with its slot filled and I'm not sure if it has been epoxied or glued in place by its appearance.
I intend to sell this gun and would like to restore the original sights if it nmakes economic sense. The gun shoots just fine as is. but I have replacement #6. .130", 3x56 threaded beads just begging to be installed. I am not a gunsmith, but I would like to know what to expect that a good gunsmith would do to remove the sights and install new ones. (Sorry---I'm trying to figure out how to reduce my image size so it can be posted) Last edited by Oregon.gun.nut; August 9, 2018 at 07:04 PM. |
August 9, 2018, 06:45 PM | #2 |
Member
Join Date: January 12, 2013
Posts: 88
|
How are they installed? I think all the Stevens ones are soldered, so unsolder, remove and solder the new ones in.
Jeff Sent from my XT1254 using Tapatalk |
August 9, 2018, 07:09 PM | #3 |
Member
Join Date: February 25, 2011
Posts: 31
|
Sorry for the delay, Jeff, while I was posting photos. Thw original sights are a bead with a 3 x 56 threaded stud, which can also be confirmed by locating the replacement part in Numrich.
|
August 9, 2018, 07:23 PM | #4 |
Senior Member
Join Date: June 20, 2007
Location: Rainbow City, Alabama
Posts: 7,167
|
If you are lucky, you could drill that broken stem and use a small EZ Out. However, I'm not sure I've ever seen one that small. That means carefully drilling the old one and chasing the threads to clean them up. That won't be easy. A slight miscalculation and you'll bugger up your threads requiring even more machining.
|
August 9, 2018, 07:52 PM | #5 |
Member
Join Date: February 25, 2011
Posts: 31
|
It's never easy is it? In this day and age of fiber optic sights, it may be easier just to make the front sight flush like the rear one and solder on a couple of beads...big fat ones!
|
August 10, 2018, 01:44 AM | #6 |
Senior Member
Join Date: February 13, 2006
Location: Washington state
Posts: 15,248
|
Most gunsmiths keep an assortment of shotgun beads on hand (I know I do!), so it should not be a major ordeal to find a replacement bead.
In order to replace the bead that broke off, it may be necessary to drill it out, or use a punch and walk it out. Then put a new bead in a pin vise and screw it in.
__________________
Never try to educate someone who resists knowledge at all costs. But what do I know? Summit Arms Services |
August 10, 2018, 06:29 AM | #7 |
Senior Member
Join Date: December 6, 2014
Posts: 6,440
|
Personally, I wouldn't worry about it as you shouldn't be looking at the beads anyway; more aggravation than it's worth.
__________________
"I believe that people have a right to decide their own destinies; people own themselves. I also believe that, in a democracy, government exists because (and only so long as) individual citizens give it a 'temporary license to exist'—in exchange for a promise that it will behave itself. In a democracy, you own the government—it doesn't own you."- Frank Zappa |
August 10, 2018, 09:29 PM | #8 |
Member
Join Date: February 25, 2011
Posts: 31
|
Thank you for all your suggestions. My father was a gunsmith and I have the bead kits and probably the tools to do the job, but I have a detached retina and glaucoma and can't see well enough to do it. For what I have in it and knowing what I can sell it for, I think it will have to stay as it is.
I appreciate everyone's input. |
August 11, 2018, 11:39 AM | #9 |
Senior Member
Join Date: February 13, 2002
Location: Canada
Posts: 12,453
|
It's not just another bead that you need. You need a broken screw extractor first.
"...can't see well enough to do it..." Take it to a smithy.
__________________
Spelling and grammar count! |
August 11, 2018, 07:40 PM | #10 |
Senior Member
Join Date: February 28, 2011
Posts: 218
|
Trip to a good gunsmith...
is the answer. A GOOD gunsmith will use a small center drill and spot drill the old bead, the drill with an undersized drill to remove the old bead shank. Then the correct tap drill can be used in a pin vise by hand to clear any remaining shank. Last the threads are refreshed with the correct tap and new beads installed.
I have been doing this for decades.... |
August 11, 2018, 08:19 PM | #11 |
Member
Join Date: February 25, 2011
Posts: 31
|
Thanks, jci54. That's exactly what I thought needed to be done. Here's my question: The nearest GOOD gunsmith is over 100 miles away. I have $195 in the gun and can only get about $300 for it in this area, repaired or not. By the time I add the charges for your work to my travel cost, does it make economic sense to do the repair?
|
August 11, 2018, 11:08 PM | #12 |
Junior member
Join Date: December 31, 2014
Location: Northwest Wisconsin
Posts: 285
|
No, you don't need a broken screw extractor. You need someone who has a #00 center drill to put a hole in the center of what's left of the bead screw. Then, it's much easier to remove.
Normally, and depending on the thread of the bead originally installed, a replacement in either silver ( aluminum ) or brass is easily replaced. |
Thread Tools | Search this Thread |
|
|